TCA9548A-Q1
- AEC-Q100 (grade 1): Qualified for automotive applications
- Functional Safety-Capable
- 1-to-8 Bidirectional translating switches
- I 2C Bus and SMBus compatible
- Active-low reset input
- Three address pins, allowing up to eight TCA9548A-Q1 devices on the I 2C bus
- Channel selection through an I 2C Bus, in any combination
- Power up with all switch channels deselected
- Low R ON switches
- Allows voltage-level translation between 1.8 V, 2.5 V, 3.3 V, and 5 V buses
- No glitch on power up
- Supports hot insertion
- Low quiescent current
- Operating power-supply voltage range of 1.65 V to 5.25 V
- 5 V tolerant Inputs
- 0 to 400 kHz clock frequency
- Latch-up performance exceeds 100 mA per JESD 78, class II
The TCA9548A-Q1 device has eight bidirectional translating switches that can be controlled through the I 2C bus. The SCL/SDA upstream pair fans out to eight downstream pairs, or channels. Any individual SCn/SDn channel or combination of channels can be selected, determined by the contents of the programmable control register. These downstream channels can be used to resolve I 2C target address conflicts. For example, if eight identical digital temperature sensors are needed in the application, one sensor can be connected at each channel: 0-7.
The system controller can reset the TCA9548A-Q1 in the event of a time-out or other improper operation by asserting a low in the RESET input. Similarly, the power-on reset deselects all channels and initializes the I 2C/SMBus state machine. Asserting RESET causes the same reset and initialization to occur without powering down the part. This allows recovery should one of the downstream I 2C buses get stuck in a low state.
The pass gates of the switches are constructed so that the VCC pin can be used to limit the maximum high voltage, which is passed by the TCA9548A-Q1. Limiting the maximum high voltage allows the use of different bus voltages on each pair, so that 1.8 V, 2.5 V or 3.3 V parts can communicate with 5 V parts, without any additional protection. External pull-up resistors pull the bus up to the desired voltage level for each channel. All I/O pins are 5 V tolerant.
기술 자료
유형 | 직함 | 날짜 | ||
---|---|---|---|---|
* | Data sheet | TCA9548A-Q1 Automotive 8-Channel I2C Switch with Reset datasheet (Rev. C) | PDF | HTML | 2023/06/09 |
Application note | I2C Solutions for Hot Swap Applications (Rev. A) | 2023/01/31 | ||
Functional safety information | TCA9548A-Q1 Functional Safety, FIT Rate, Failure Mode Distribution and Pin FMA | PDF | HTML | 2021/02/22 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
TCA9548AEVM — TCA9548A I2C 1-8 양방향 변환 스위치 평가 모듈
The TCA9548AEVM is designed to evaluate and demonstrate the functionality of TI’s TCA954xA family of I2C switches. The TCA9548AEVM can be used as a standalone evaluation module to interface with an existing system or paired with the MSP430 Lauchpad which serves as the I2C master and power supply (...)
I2C-DESIGNER — I2C 디자이너 툴
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
TINA-TI — SPICE 기반 아날로그 시뮬레이션 프로그램
패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
---|---|---|
VQFN (RGE) | 24 | Ultra Librarian |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.