SPRACZ7 January   2022 TMS320F28075 , TMS320F28075-Q1 , TMS320F28076 , TMS320F28232 , TMS320F28232-Q1 , TMS320F28234 , TMS320F28234-Q1 , TMS320F28235 , TMS320F28235-Q1 , TMS320F28332 , TMS320F28333 , TMS320F28334 , TMS320F28335 , TMS320F28335-Q1 , TMS320F28374D , TMS320F28374S , TMS320F28375D , TMS320F28375S , TMS320F28375S-Q1 , TMS320F28376D , TMS320F28376S , TMS320F28377D , TMS320F28377D-EP , TMS320F28377D-Q1 , TMS320F28377S , TMS320F28377S-Q1 , TMS320F28378D , TMS320F28378S , TMS320F28379D , TMS320F28379D-Q1 , TMS320F28379S

 

  1.   Trademarks
  2. 1 Introduction
    1. 1.1 Abbreviations
  3. 2 Central Processing Unit (CPU)
  4. 3 Development Tools
    1. 3.1 Driver Library (Driverlib)
    2. 3.2 Embedded Application Binary Interface (EABI) Support
  5. 4 Package and Pinout
  6. 5 Operating Frequency and Power Management
  7. 6 Power Sequencing
  8. 7 Input Clock Options
  9. 8 Memory Map
  10. 9 Flash and OTP
    1. 9.1 Size and Number of Sectors
    2. 9.2 Flash Parameters
    3. 9.3 Flash Programming
    4. 9.4 Entry Point into Flash
    5. 9.5 Dual Code Security Module (DCSM) and Password Locations
    6. 9.6 OTP
  11. 10Boot ROM
    1. 10.1 Boot ROM Reserved RAM
    2. 10.2 Boot Mode Selection
    3. 10.3 Bootloaders
  12. 11Architectural Enhancements
    1. 11.1 Clock Sources and Domains
    2. 11.2 Watchdog Timer
    3. 11.3 Peripheral Interrupt Expansion (PIE)
    4. 11.4 Lock Protection Registers
    5. 11.5 General-Purpose Input/Output (GPIO)
    6. 11.6 External Interrupts
    7. 11.7 Crossbar (X-BAR)
  13. 12Peripherals
    1. 12.1 New Peripherals
      1. 12.1.1 Analog Subsystem Interconnect
      2. 12.1.2 Comparator Subsystem (CMPSS)
      3. 12.1.3 Control Law Accelerator (CLA)
    2. 12.2 Control Peripherals
      1. 12.2.1 Enhanced Pulse Width Modulator (ePWM)
      2. 12.2.2 Enhanced Capture Module (eCAP)
      3. 12.2.3 Enhanced Quadrature Encode Pulse Module (eQEP)
      4. 12.2.4 Sigma-Delta Filter Module (SDFM)
    3. 12.3 Analog Peripherals
      1. 12.3.1 Analog-to-Digital Converter (ADC)
    4. 12.4 Communication Peripherals
      1. 12.4.1 SPI
      2. 12.4.2 SCI
      3. 12.4.3 USB
      4. 12.4.4 I2C
      5. 12.4.5 CAN
  14. 13Configurable Logic Block (CLB)
  15. 14Device Comparison Summary
  16. 15References

11.1 Clock Sources and Domains

There are numerous enhancement and changes to the clock sources and additional clock domains on the F2837xD/S/07x device. These major enhancements and changes include:

  • Increase in the number of Peripheral Clock Gating Register to handle the additional and new peripherals
  • INTOSC2 is the primary internal clock source and is the default system clock at reset
  • INTOSC1 is a backup clock source which normally only clocks the watchdog timers and missing clock detection circuit (MCD)
  • External Clock Source (XTAL) can be used as the main system and CAN bit clock source; frequency limits and timing requirements can be found in the datasheets
  • External Clock Output (XCLKOUT) can be routed to GPIO73, and the available clock sources are PLLSYSCLK, PLLRAWCLK, CPU1.SYSCLK, CPU2.SYSCLK, AUXPLLRAWCLK, INTOSC1, and INTOSC2.
  • SYSPLL Integer Multiplier (IMULT) can vary from 1 to 127. SYSPLL Fractional Multiplier (FMULT) supports four different values: 0, 0.25, 0.5 and 0.75.
  • PLLSYSCLK Divide Select (PLLSYSCLKDIV) can be a value of either 1 or an even value up to 126
  • XCLKOUT Divide Select (XCLKOUTDIV) has /8 (default on reset) in addition to /1, /2, and /4