SPRAAU8A March   2008  – August 2017 TMS320F2801 , TMS320F2801 , TMS320F2801-Q1 , TMS320F2801-Q1 , TMS320F28015 , TMS320F28015 , TMS320F28016 , TMS320F28016 , TMS320F28016-Q1 , TMS320F28016-Q1 , TMS320F2802 , TMS320F2802 , TMS320F2802-Q1 , TMS320F2802-Q1 , TMS320F28044 , TMS320F28044 , TMS320F2806 , TMS320F2806 , TMS320F2806-Q1 , TMS320F2806-Q1 , TMS320F28062 , TMS320F28062 , TMS320F28062-Q1 , TMS320F28062-Q1 , TMS320F28062F , TMS320F28062F , TMS320F28062F-Q1 , TMS320F28062F-Q1 , TMS320F28063 , TMS320F28063 , TMS320F28064 , TMS320F28064 , TMS320F28065 , TMS320F28065 , TMS320F28066 , TMS320F28066 , TMS320F28066-Q1 , TMS320F28066-Q1 , TMS320F28067 , TMS320F28067 , TMS320F28067-Q1 , TMS320F28067-Q1 , TMS320F28068F , TMS320F28068F , TMS320F28068M , TMS320F28068M , TMS320F28069 , TMS320F28069 , TMS320F28069-Q1 , TMS320F28069-Q1 , TMS320F28069F , TMS320F28069F , TMS320F28069F-Q1 , TMS320F28069F-Q1 , TMS320F28069M , TMS320F28069M , TMS320F28069M-Q1 , TMS320F28069M-Q1 , TMS320F2808 , TMS320F2808 , TMS320F2808-Q1 , TMS320F2808-Q1 , TMS320F2809 , TMS320F2809 , TMS320F2810 , TMS320F2810 , TMS320F2810-Q1 , TMS320F2810-Q1 , TMS320F2811 , TMS320F2811 , TMS320F2811-Q1 , TMS320F2811-Q1 , TMS320F2812 , TMS320F2812 , TMS320F2812-Q1 , TMS320F2812-Q1 , TMS320F28232 , TMS320F28232 , TMS320F28232-Q1 , TMS320F28232-Q1 , TMS320F28234 , TMS320F28234 , TMS320F28234-Q1 , TMS320F28234-Q1 , TMS320F28235 , TMS320F28235 , TMS320F28235-Q1 , TMS320F28235-Q1 , TMS320F28332 , TMS320F28332 , TMS320F28333 , TMS320F28333 , TMS320F28334 , TMS320F28334 , TMS320F28335 , TMS320F28335 , TMS320F28335-Q1 , TMS320F28335-Q1

 

  1.   Copying Compiler Sections From Flash to RAM on the TMS320F28xxx DSCs
    1.     Trademarks
    2. 1 Introduction
    3. 2 Compiler Sections
    4. 3 Software
      1. 3.1 Description
        1. 3.1.1 Code_start and wd_disable
        2. 3.1.2 Copy_sections
        3. 3.1.3 Memory Allocation – Linker Command Files
      2. 3.2 Testing Example
        1. 3.2.1 Code Composer Studio Environment
        2. 3.2.2 Standalone Operation
      3. 3.3 Application Integration
        1. 3.3.1 Example Integration
    5. 4 Benchmarks, Limitations, and Suggestions
      1. 4.1 Memory Usage
      2. 4.2 Benchmarks
      3. 4.3 Limitations
      4. 4.4 Suggestions
    6. 5 Conclusion
    7. 6 References
  2.   Revision History

3.2.2 Standalone Operation

  1. Follow the procedures given in Section 3.2.1 to program the example to the eZdsp development board.
  2. Close Code Composer Studio and disconnect the USB cable.
  3. Configure SW1 for Boot to Flash mode. For more information, see the eZdsp™ F2808 USB Technical Reference (www.spectrumdigital.com).
  4. Remove power and reapply power to the eZdsp.

The LED on the eZdsp should be flashing to indicate that the program is running.