Inicio Gestión de la energía Interruptores de potencia Fusibles electrónicos y controladores de intercambio en caliente
Inicio
Gestión de la energía
Interruptores de potencia
Fusibles electrónicos y controladores de intercambio en caliente

TPS25984

ACTIVO

Fusible electrónico apilable de 4,5 V a 16 V, 0,8 mΩ, 70 A con monitor de corriente preciso y rápido

Haga su pedido ahora
Hoja de datos

TPS25984

ACTIVO
Hoja de datos Haga su pedido ahora

Detalles del producto

FET Internal Ron (typ) (mΩ) 0.8 Vin (min) (V) 4.5 Vin (max) (V) 16 Vabsmax_cont (V) 20 Current limit (min) (A) 10 Current limit (max) (A) 55 Overcurrent response Circuit breaker Fault response Auto-retry, Latch-off Soft start Adjustable Overvoltage response Cut-off Features Current monitoring, Fault output, Over Current Protection, Overvoltage protection, Power good signal, Short-circuit protection, Soft-start, Thermal shutdown Rating Catalog Device type eFuses and hot swap controllers Operating temperature range (°C) -40 to 125 Function Adjustable current limit, Current monitoring, Inrush current control, Overvoltage protection, Power good signal, Short circuit protection, Thermal shutdown Quiescent current (Iq) (typ) (A) 0.004 Quiescent current (Iq) (max) (A) 0.00055
FET Internal Ron (typ) (mΩ) 0.8 Vin (min) (V) 4.5 Vin (max) (V) 16 Vabsmax_cont (V) 20 Current limit (min) (A) 10 Current limit (max) (A) 55 Overcurrent response Circuit breaker Fault response Auto-retry, Latch-off Soft start Adjustable Overvoltage response Cut-off Features Current monitoring, Fault output, Over Current Protection, Overvoltage protection, Power good signal, Short-circuit protection, Soft-start, Thermal shutdown Rating Catalog Device type eFuses and hot swap controllers Operating temperature range (°C) -40 to 125 Function Adjustable current limit, Current monitoring, Inrush current control, Overvoltage protection, Power good signal, Short circuit protection, Thermal shutdown Quiescent current (Iq) (typ) (A) 0.004 Quiescent current (Iq) (max) (A) 0.00055
WQFN-FCRLF (RZJ) 32 25 mm² 5 x 5
  • Input operating voltage range: 4.5 V to 16 V
    • Absolute maximum: 20 V
    • Withstands negative voltages up to –1 V at output
  • Integrated FET with ultra-low on-resistance: 0.8 mΩ (typical)
  • Rated for RMS current of 55 A and peak current of 70 A
  • Supports parallel connection of multiple eFuses for higher current support
    • Active device state synchronization and load sharing during start-up and steady-state
  • Robust overcurrent protection
    • Adjustable overcurrent threshold (I OCP): 10 A to 55 A with accuracy of ±5%
    • Circuit-breaker response during steady state operation with adjustable transient overcurrent timer (ITIMER) to support peak currents up to 2 × I OCP
    • Adjustable active current limit during start-up (I LIM)
  • Robust short-circuit protection
    • Fast-trip response (< 200 ns) to output short-circuit events
    • Adjustable threshold (2 × I OCP)
    • Immune to supply line transients — no nuisance tripping
  • Precise analog load current monitoring
    • Accuracy: ±1.4 %
    • Bandwidth: > 500 kHz
  • Fast overvoltage protection (fixed 16.7-V threshold)
  • Adjustable output slew rate control (dVdt) for inrush current protection
  • Active high enable input with adjustable undervoltage lockout (UVLO)
  • Overtemperature Protection (OTP) to ensure FET SOA
    • Guaranteed FET SOA: 10 W√s
  • Integrated FET health monitoring and reporting
  • Analog die temperature monitor output (TEMP)
  • Dedicated fault indication pin ( FLT)
  • Power-Good indication pin (PG)
  • Small footprint: QFN 5 mm × 5 mm
  • 100% Pb free
  • Input operating voltage range: 4.5 V to 16 V
    • Absolute maximum: 20 V
    • Withstands negative voltages up to –1 V at output
  • Integrated FET with ultra-low on-resistance: 0.8 mΩ (typical)
  • Rated for RMS current of 55 A and peak current of 70 A
  • Supports parallel connection of multiple eFuses for higher current support
    • Active device state synchronization and load sharing during start-up and steady-state
  • Robust overcurrent protection
    • Adjustable overcurrent threshold (I OCP): 10 A to 55 A with accuracy of ±5%
    • Circuit-breaker response during steady state operation with adjustable transient overcurrent timer (ITIMER) to support peak currents up to 2 × I OCP
    • Adjustable active current limit during start-up (I LIM)
  • Robust short-circuit protection
    • Fast-trip response (< 200 ns) to output short-circuit events
    • Adjustable threshold (2 × I OCP)
    • Immune to supply line transients — no nuisance tripping
  • Precise analog load current monitoring
    • Accuracy: ±1.4 %
    • Bandwidth: > 500 kHz
  • Fast overvoltage protection (fixed 16.7-V threshold)
  • Adjustable output slew rate control (dVdt) for inrush current protection
  • Active high enable input with adjustable undervoltage lockout (UVLO)
  • Overtemperature Protection (OTP) to ensure FET SOA
    • Guaranteed FET SOA: 10 W√s
  • Integrated FET health monitoring and reporting
  • Analog die temperature monitor output (TEMP)
  • Dedicated fault indication pin ( FLT)
  • Power-Good indication pin (PG)
  • Small footprint: QFN 5 mm × 5 mm
  • 100% Pb free

The TPS25984x is an integrated, high-current circuit protection and power management solution in a small package. The device provides multiple protection modes using very few external components and is a robust defense against overloads, short circuits, and excessive inrush current.

Applications with particular inrush current requirements can set the output slew rate with a single external capacitor. Output current limit level can be set by user as per system needs. A user adjustable overcurrent blanking timer allows systems to support transient peaks in the load current without tripping the eFuse.

Multiple TPS25984x devices can be connected in parallel to increase the total current capacity for high power systems. All devices actively synchronize their operating state and share current during start-up as well as steady state to avoid over-stressing some of the devices which can result in premature or partial shutdown of the parallel chain.

An integrated fast and accurate sense analog load current monitor facilitates predictive maintenance and advanced dynamic platform power management techniques such as Intel PSYS and PROCHOT™ to maximize system throughput and power supply utilization.

The devices are characterized for operation over a junction temperature range of –40°C to +125°C.

The TPS25984x is an integrated, high-current circuit protection and power management solution in a small package. The device provides multiple protection modes using very few external components and is a robust defense against overloads, short circuits, and excessive inrush current.

Applications with particular inrush current requirements can set the output slew rate with a single external capacitor. Output current limit level can be set by user as per system needs. A user adjustable overcurrent blanking timer allows systems to support transient peaks in the load current without tripping the eFuse.

Multiple TPS25984x devices can be connected in parallel to increase the total current capacity for high power systems. All devices actively synchronize their operating state and share current during start-up as well as steady state to avoid over-stressing some of the devices which can result in premature or partial shutdown of the parallel chain.

An integrated fast and accurate sense analog load current monitor facilitates predictive maintenance and advanced dynamic platform power management techniques such as Intel PSYS and PROCHOT™ to maximize system throughput and power supply utilization.

The devices are characterized for operation over a junction temperature range of –40°C to +125°C.
filter Buscar otro/a Fusibles electrónicos y controladores de intercambio en caliente
Descargar Ver vídeo con transcripción Video

Documentación técnica

star =Principal documentación para este producto seleccionada por TI
No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 4
Tipo Título Fecha
* Data sheet TPS25984x 4.5 V – 16 V, 0.8-mΩ, 70-A Stackable eFuse With Accurate and Fast Current Monitor datasheet (Rev. A) PDF | HTML 12 oct 2023
Application note Implementation of PSYS Monitor Using TPS25984, TPS25985, or TPS25990 eFuses PDF | HTML 15 nov 2023
EVM User's guide TPS25984 Evaluation Module (EVM) (Rev. A) PDF | HTML 02 nov 2023
Certificate TPS25984EVM EU RoHS Declaration of Conformity (DoC) 11 nov 2022

Diseño y desarrollo

Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.

Placa de evaluación

TPS25984EVM — Módulo de evaluación TPS25984 para fusible electrónico de 4.5 V a 16 V 70 A 0.8 mΩ

La placa de evaluación TPS25984 de fusibles electrónicos permite la evaluación del circuito de referencia del TPS25984 de fusibles electrónicos. El dispositivo TPS25984 es un fusible electrónico de 4.5 V a 16 V 70 A con FET integrado de 0.8 mΩ. Incluye gestión de sobrecorriente y corriente de (...)

Guía del usuario: PDF | HTML
No disponible en TI.com
Herramienta de cálculo

TPS25984-CALC — TPS25984 design calculator

The design calculator allows customer to size the external peripheral components while designing with one or more TPS25984 eFuse.
Productos y hardware compatibles

Productos y hardware compatibles

Productos
Fusibles electrónicos y controladores de intercambio en caliente
TPS25984 — Fusible electrónico apilable de 4,5 V a 16 V, 0,8 mΩ, 70 A con monitor de corriente preciso y rápido
Descargar
Herramienta de cálculo

TVS-RECOMMENDATION-CALC — TVS diode recommendation tool

This tool suggests suitable TVS for given system parameters and abs max voltage rating of the device.
Productos y hardware compatibles

Productos y hardware compatibles

Este recurso de diseño es compatible con la mayoría de los productos de estas categorías.

Revise la página de detalles del producto para verificar la compatibilidad.
Descargar
Herramienta de simulación

PSPICE-FOR-TI — PSpice® para herramienta de diseño y simulación de TI

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Solicitar
Encapsulado Pines Símbolos CAD, huellas y modelos 3D
WQFN-FCRLF (RZJ) 32 Ultra Librarian
Se aplican los Términos y condiciones estándar de TI para los elementos de evaluación.

Pedidos y calidad

Información incluida:
  • RoHS
  • REACH
  • Marcado del dispositivo
  • Acabado de plomo/material de la bola
  • Clasificación de nivel de sensibilidad a la humedad (MSL) / reflujo máximo
  • Estimaciones de tiempo medio entre fallas (MTBF)/fallas en el tiempo (FIT)
  • Contenido del material
  • Resumen de calificaciones
  • Monitoreo continuo de confiabilidad
Información incluida:
  • Lugar de fabricación
  • Lugar de ensamblaje

Los productos recomendados pueden tener parámetros, módulos de evaluación o diseños de referencia relacionados con este producto de TI.

Soporte y capacitación

Foros de TI E2E™ con asistencia técnica de los ingenieros de TI

Ver todos los temas del foro en inglés

El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.

Si tiene preguntas sobre la calidad, el paquete o el pedido de productos de TI, consulte el soporte de TI. ​​​​​​​​​​​​​​

Videos