SPRACY5 July   2021 AM67 , AM67 , AM67A , AM67A , AM68 , AM68 , AM68A , AM68A , AM69 , AM69 , AM69A , AM69A , DRA821U , DRA821U , DRA821U-Q1 , DRA821U-Q1 , DRA829J , DRA829J , DRA829J-Q1 , DRA829J-Q1 , DRA829V , DRA829V , DRA829V-Q1 , DRA829V-Q1 , TDA4AEN-Q1 , TDA4AEN-Q1 , TDA4AH-Q1 , TDA4AH-Q1 , TDA4AL-Q1 , TDA4AL-Q1 , TDA4AP-Q1 , TDA4AP-Q1 , TDA4VE-Q1 , TDA4VE-Q1 , TDA4VEN-Q1 , TDA4VEN-Q1 , TDA4VH-Q1 , TDA4VH-Q1 , TDA4VL-Q1 , TDA4VL-Q1 , TDA4VM , TDA4VM , TDA4VM-Q1 , TDA4VM-Q1 , TDA4VP-Q1 , TDA4VP-Q1

 

  1.   Trademarks
  2. 1Introduction to Flashing Tools
    1. 1.1 Trace32/Lauterbach
    2. 1.2 CCS-Based Flash Writer
    3. 1.3 Other Software Tools
  3. 2Flash Devices on TDA4
    1. 2.1 Flashing OSPI and eMMC RAW Sectors
    2. 2.2 Flashing eMMC User Partition
  4. 3Prerequisites for Flashing TDA4
    1. 3.1 Boot Switch Settings
    2. 3.2 How to Generate a Tiny File System
    3. 3.3 Generating the eMMC tisdk-tiny-image.img
    4. 3.4 Running Until u-boot
      1. 3.4.1 UART Boot Mode
      2. 3.4.2 DFU Boot
      3. 3.4.3 SD Boot or any Other Boot Mode
    5. 3.5 Configuring Boot0 Partition and Partitioning eMMC
  5. 4OSPI Flashing
    1. 4.1 Flashing Bootloader Binaries
      1. 4.1.1 TI UNIFLASH Tool
        1. 4.1.1.1 Flashing Instructions
        2. 4.1.1.2 Linux Boot Binaries
        3. 4.1.1.3 RTOS Boot Binaries
    2. 4.2 dfu-util
      1. 4.2.1 Flashing Instructions
    3. 4.3 CCS/JTAG
      1. 4.3.1 Flashing Instructions
    4. 4.4 Trace32/Lauterbach
      1. 4.4.1 Flashing Instructions
    5. 4.5 u-boot
      1. 4.5.1 Flashing Instructions
  6. 5eMMC flashing
    1. 5.1 Flashing Bootloader Binaries
      1. 5.1.1 TI UNIFLASH Tool
        1. 5.1.1.1 Flashing Instructions
      2. 5.1.2 Trace32/Lauterbach
        1. 5.1.2.1 Flashing Instructions
      3. 5.1.3 dfu-util
        1. 5.1.3.1 Flashing Instructions
    2. 5.2 u-boot
      1. 5.2.1 Flashing Instructions
    3. 5.3 eMMC UDA Partition Flashing With tinyrootfs
      1. 5.3.1 dfu-util
      2. 5.3.2 u-boot + CCS/JTAG
        1. 5.3.2.1 Flashing Instructions

CCS-Based Flash Writer

Some custom boards only have a JTAG interface along with OSPI/QSPI flash. In absence of Trace32/Lauterbach, there is a Code Composer Studio™-based software flash writer application to flash the on-board flashes.

The solution provides an application that runs on MCU R5 and then provides a user-friendly menu to write and erase to the OSPI/QSPI flash.

GUID-20210624-CA0I-3V75-WBCG-KW5HXWQNSJNK-low.gif Figure 1-2 CCS-Based Flash Writer Flashing