Firmware
TCA9535
Expansor de E/S I2C/SMBus de 1.65 V a 5.5 V de 16 bits con registros de interrupción y configuración
Hoja de datos
TCA9535
- I2C to Parallel port expander
- Wide power supply voltage range of 1.65 V to 5 V
- Low standby-current consumption
- Open-drain active-low interrupt output
- 5-V tolerant I/O ports
- 400-kHz Fast I2C bus
- Polarity inversion register
- Address by three hardware address pins for use of up to eight devices
- Latched outputs with high-current drive capability for directly driving LEDs
- Latch-up performance exceeds 100 mA per JESD 78, class II
- ESD protection exceeds JESD 22
- 2000-V Human-Body Model (A114-A)
- 1000-V Charged-Device Model (C101)
The TCA9535 is a 24-pin device that provides 16 bits of general purpose parallel input and output (I/O) expansion for the two-line bidirectional I2C bus or (SMBus) protocol. The device can operate with a power supply voltage ranging from 1.65 V to 5.5 V.
The TCA9535 consists of two 8-bit Configuration (input or output selection), Input Port, Output Port, and Polarity Inversion (active-high or active-low operation) registers. At power on, the I/Os are configured as inputs. The system controller can enable the I/Os as either inputs or outputs by writing to the I/O configuration bits.
The TCA9535 is identical to the TCA9555, except that the TCA9535 does not include the internal I/O pull-up resistor, which requires pull-ups and pull-downs on unused I/O pins when configured as an input and undriven.
Documentación técnica
No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 8 | Tipo | Título | Fecha | ||
|---|---|---|---|---|
| * | Data sheet | TCA9535 Low-Voltage 16-Bit I2C and SMBus Low-Power I/O Expander with Interrupt Output and Configuration Registers datasheet (Rev. E) | PDF | HTML | 06 may 2022 |
| Application note | Understanding Transient Drive Strength vs. DC Drive Strength in CMOS Output Buffers | PDF | HTML | 14 may 2024 | |
| Application note | I2C Dynamic Addressing | 25 abr 2019 | ||
| Application note | Choosing the Correct I2C Device for New Designs | PDF | HTML | 07 sep 2016 | |
| Application note | Understanding the I2C Bus | PDF | HTML | 30 jun 2015 | |
| Application note | Maximum Clock Frequency of I2C Bus Using Repeaters | 15 may 2015 | ||
| Application note | I2C Bus Pull-Up Resistor Calculation | PDF | HTML | 13 feb 2015 | |
| EVM User's guide | I/O Expander EVM User's Guide (Rev. A) | 25 jul 2014 |
Diseño y desarrollo
Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.
Placa de evaluación
IO-EXPANDER-EVM — IO-EXPANDER-EVM: Módulo de evaluación de expansión de E/S I2C y SMBus
El módulo de evaluación (EVM) de expansión de E/S le permite evaluar la cartera de dispositivos de la línea de expansión de E/S SMBus y I2C de TI . Tanto el TCA6424A como el TCA9539 están instalados en la placa. El formato TSSOP de 24 pines también admite TCA6408A, TCA6416A, TCA9534, TCA9534A, (...)
Guía del usuario: PDF
Herramienta de diseño
I2C-DESIGNER — Herramienta de diseño I2C
Use the I2C Designer tool to quickly resolve conflicts in addressing, voltage level and frequency in I2C based designs. Enter master and slave inputs to automatically generate an I2C tree or easily build a custom solution. This tool will help designers save time and comply with the I2C standard (...)
Herramienta de simulación
PSPICE-FOR-TI — PSpice® para herramienta de diseño y simulación de TI
PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Herramienta de simulación
TINA-TI — Programa de simulación analógica basado en SPICE
TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
Guía del usuario: PDF
Diseños de referencia
TIDA-00420 — Diseño de referencia de entrada binaria de CA/CC de 16 canales, entrada amplia, aislado digitalmente
This reference design showcases a cost-optimized and scalable ADC-based AC/DC binary input module (BIM) architecture with reinforced isolation. The 16 channels of a 10- or 12-bit SAR ADC are used for sensing multiple binary inputs. The op amps, in addition to keeping the cost per-channel low, (...)
Diseños de referencia
TIDM-CAPTOUCHEMCREF — Diseño de referencia de HMI táctil capacitiva y tolerante al ruido
The Noise Tolerant Capacitive Touch HMI design (TIDM-CAPTOUCHEMCREF) is a reference design for implementing noise tolerant capacitive touch human-machine interfaces (HMIs). It integrates TI's MSP430FR2633 microcontroller (MCU) featuring high performance CapTIvate™ touch technology with (...)
Diseños de referencia
TIDA-01579 — Diseño de referencia de fuente de alimentación de rizado de baja salida y alta eficiencia para aplic
The point-of-load power-tree on video surveillance systems is optimized with this reference design. This reference design has a high performance on key parameters such as output voltage accuracy, voltage ripple, and thermal dissipation. This high performance is possible with a small board area and (...)
Diseños de referencia
TIDA-00246 — Diseño de referencia del módulo del adaptador de captación de energía genérico para generadores term
This reference design aims at providing a generic solution for energy harvesting while giving a practical application application for thermoelectric generators (TEG). It is a fully programmable state-machine which runs at 60nA and can enable and disable key functions as they are needed by the (...)
Diseños de referencia
TIDA-00468 — Diseño de referencia del extremo frontal de detección de termopar de huella de memoria, potencia y l
The TIDA-00468 Reference design shows how to build an isolated thermocouple sensing front-end with optimized power-consumption for loop powered application while:
• reducing footprint from classical look-up table approach and
• keeping the fast response time of linear piece wise interpolation
• reducing footprint from classical look-up table approach and
• keeping the fast response time of linear piece wise interpolation
Diseños de referencia
TIDA-00168 — Termopar AFE con RTD o sensor de temperatura integrado para compensación de unión fría (CJC)
The sole objective of this reference design is to provide comprehensive details on how to design a simple, robust, and accurate analog front end (AFE) circuit for making precision temperature measurements with thermocouple sensors. TIDA-00168 explains the theory, operation, and complications (...)
| Encapsulado | Pines | Símbolos CAD, huellas y modelos 3D |
|---|---|---|
| SSOP (DB) | 24 | Ultra Librarian |
| TSSOP (PW) | 24 | Ultra Librarian |
| VQFN (RGE) | 24 | Ultra Librarian |
| WQFN (RTW) | 24 | Ultra Librarian |
Pedidos y calidad
Información incluida:
- RoHS
- REACH
- Marcado del dispositivo
- Acabado de plomo/material de la bola
- Clasificación de nivel de sensibilidad a la humedad (MSL) / reflujo máximo
- Estimaciones de tiempo medio entre fallas (MTBF)/fallas en el tiempo (FIT)
- Contenido del material
- Resumen de calificaciones
- Monitoreo continuo de confiabilidad
Información incluida:
- Lugar de fabricación
- Lugar de ensamblaje
Los productos recomendados pueden tener parámetros, módulos de evaluación o diseños de referencia relacionados con este producto de TI.
Soporte y capacitación
Foros de TI E2E™ con asistencia técnica de los ingenieros de TI
El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.
Si tiene preguntas sobre la calidad, el paquete o el pedido de productos de TI, consulte el soporte de TI.