BQ25672
- High power density, high integration buck charger for 1-4 cell batteries
- Integrates switching MOSFETs, BATFET
- Integrates input and charging current sensing
- Highly efficient
- 750-kHz or 1.5-MHz switching frequencies
- 3-A charging current with 10-mA resolution
- 96.5% efficient: 16-V battery at 3A from 20V
- Supports a wide range of input sources
- Autonomously sampled open circuit voltage (V OC) maximum power point tracking (MPPT) for charging from a photovoltaic panel
- 3.6-V to 24-V wide input operating voltage range with 30-V absolute maximum rating
- Maximum power tracking with input voltage dynamic power management (VINDPM) up to 22 V and input current dynamic power management (IINDPM) up to 3.3 A
- Detects USB BC1.2, HVDCP and non-standard adapters
- Dual-input power mux controller (optional) for source selection
- Narrow voltage DC (NVDC) power path
- Powers USB port from battery (USB OTG)
- 5-V to 12-V OTG buck-boost output voltage with 10-mV resolution
- OTG output current regulation up to 2 A with 40-mA resolution
- Flexible autonomous and I 2C mode for optimal system performance
- Integrated 16-bit ADC for voltage, current, and temperature monitoring
- Low battery quiescent current
- 17 µA for battery only operation
- 500 nA in Charger Shutdown Mode
- High accuracy
- -0.25% to +0.65% charge voltage regulation for 2S batteries
- ±5% charge current regulation
- ±5% input current regulation
- Safety
- Thermal regulation and thermal shutdown
- Input/battery OVP and OCP
- Converter MOSFETs OCP
- Charging safety timer
- Package
- 29-Pin 4 mm × 4 mm QFN
The BQ25672 is a fully integrated switch-mode buck charger for 1-4 cell Li-ion batteries and Li-polymer batteries. The BQ25672 is also capable of producing a buck-boost, 5 V to 12 V, output voltage on VBUS when operating in OTG Mode. The integration includes the switching MOSFETs, input and charging current sensing circuits, the battery FET and all the loop compensation of the converter. It uses NVDC power path management, regulating the system not dropping below a configurable minimum system voltage. When system power exceeds the input source rating, battery supplement mode supports the system without overloading the input source. also maximizes power from photovoltaic panels using its built-in V OC scaling MPPT algorithm.
技術文件
設計與開發
如需其他條款或必要資源,請按一下下方的任何標題以檢視詳細頁面 (如有)。
BQ25672EVM — 適用 I²C 控制、1 至 4 芯、3-A 降壓充電器與雙輸入和 MPPT 的 BQ25672 評估模組
TI-CHARGER-GUI — 適於與 USB2ANY 和電池充電搭配使用的 GUI 軟體評估模組
封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
---|---|---|
VQFN-HR (RQM) | 29 | Ultra Librarian |
訂購與品質
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 認證摘要
- 進行中持續性的可靠性監測
- 晶圓廠位置
- 組裝地點
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。