首頁 電池管理 IC 電池充電器 IC
首頁
電池管理 IC
電池充電器 IC

LM3658

現行

適用可攜式應用的雙來源 USB/AC 化學充電器 IC

立即訂購
產品規格表

LM3658

現行
產品規格表 立即訂購

產品詳細資料

Number of series cells 1 Charge current (max) (A) 1 Vin (max) (V) 6 Cell chemistry Li-Ion/Li-Polymer Battery charge voltage (min) (V) 4.2 Battery charge voltage (max) (V) 4.2 Absolute max Vin (max) (V) 6.5 Control topology Linear Control interface Standalone (RC-Settable) Features BAT temp thermistor monitoring (hot/cold profile), IC thermal regulation Vin (min) (V) 4.5 Rating Catalog Operating temperature range (°C) -40 to 85
Number of series cells 1 Charge current (max) (A) 1 Vin (max) (V) 6 Cell chemistry Li-Ion/Li-Polymer Battery charge voltage (min) (V) 4.2 Battery charge voltage (max) (V) 4.2 Absolute max Vin (max) (V) 6.5 Control topology Linear Control interface Standalone (RC-Settable) Features BAT temp thermistor monitoring (hot/cold profile), IC thermal regulation Vin (min) (V) 4.5 Rating Catalog Operating temperature range (°C) -40 to 85
WSON (DSC) 10 9 mm² 3 x 3
  • Integrated power FETs with thermal regulation
  • Charges from either an AC wall adapter or USB power source with automatic source selection
  • 50 mA to 1000 mA charge currents using AC wall adapter
  • Pin-selectable USB charge currents of 100 mA or 500 mA
  • LDO mode with 1A of source current is automatically invoked when the battery is absent and the AC wall adapter is connected
  • Continuous battery temperature monitoring
  • Built-in multiple safety timers
  • Charge status indication
  • Continuous over-current and temperature protection
  • Near-depleted battery pre-conditioning
  • Sleep mode with ultra low quiescent current
  • On-board Kelvin-sensing achieves ±0.35% termination accuracy
  • Maintenance mode with automatic recharge
  • Thermally enhanced 3 mm x 3 mm LLP package
    •
  • Integrated power FETs with thermal regulation
  • Charges from either an AC wall adapter or USB power source with automatic source selection
  • 50 mA to 1000 mA charge currents using AC wall adapter
  • Pin-selectable USB charge currents of 100 mA or 500 mA
  • LDO mode with 1A of source current is automatically invoked when the battery is absent and the AC wall adapter is connected
  • Continuous battery temperature monitoring
  • Built-in multiple safety timers
  • Charge status indication
  • Continuous over-current and temperature protection
  • Near-depleted battery pre-conditioning
  • Sleep mode with ultra low quiescent current
  • On-board Kelvin-sensing achieves ±0.35% termination accuracy
  • Maintenance mode with automatic recharge
  • Thermally enhanced 3 mm x 3 mm LLP package
    •

    The LM3658 is a single chip charger IC designed for handheld applications. It can safely charge and maintain a single cell Li-Ion/Polymer battery operating from an AC wall adapter or USB power source. Input power source selection of USB/AC is automatic. With both power sources present, the AC power source has priority. Charge current is programmed through an external resistor when operating from an AC wall adapter allowing charge currents from 50 mA to 1000 mA. When the battery is charged using USB power, charge currents of 100 mA or 500 mA are pin-selectable. The termination voltage is controlled to within ±0.35% of 4.2V.

    The LM3658 requires few external components and integrates internal power FETs, reverse current protection and current sensing. The internal power FETs are thermally regulated to obtain the most efficient charging rate for a given ambient temperature.

    The LM3658 operates in five modes: pre-qualification mode, constant-current mode, constant-voltage mode, top-off mode and maintenance mode. Additionally, the charger IC operates as a linear regulator in “LDO mode”, when the AC wall adapter is connected and no battery is present. Optimal battery management is obtained through thermal regulation, battery temperature measurement and multiple safety timers. The LM3658 provides two open-drain outputs for LED status indication or connection to GPIOs.

    The LM3658 is a single chip charger IC designed for handheld applications. It can safely charge and maintain a single cell Li-Ion/Polymer battery operating from an AC wall adapter or USB power source. Input power source selection of USB/AC is automatic. With both power sources present, the AC power source has priority. Charge current is programmed through an external resistor when operating from an AC wall adapter allowing charge currents from 50 mA to 1000 mA. When the battery is charged using USB power, charge currents of 100 mA or 500 mA are pin-selectable. The termination voltage is controlled to within ±0.35% of 4.2V.

    The LM3658 requires few external components and integrates internal power FETs, reverse current protection and current sensing. The internal power FETs are thermally regulated to obtain the most efficient charging rate for a given ambient temperature.

    The LM3658 operates in five modes: pre-qualification mode, constant-current mode, constant-voltage mode, top-off mode and maintenance mode. Additionally, the charger IC operates as a linear regulator in “LDO mode”, when the AC wall adapter is connected and no battery is present. Optimal battery management is obtained through thermal regulation, battery temperature measurement and multiple safety timers. The LM3658 provides two open-drain outputs for LED status indication or connection to GPIOs.

    filter 尋找其它 電池充電器 IC
    下載 觀看有字幕稿的影片 影片

    您可能會感興趣的類似產品

    open-in-new 比較替代產品
    功能與所比較的裝置相似
    BQ24079 現行 獨立式 1 芯 1.5-A 線性電池充電器、電源路徑和 4.1-V VBAT This product is a standalone 1-cell 1.5-A linear battery charger with PowerPath

    技術文件

    star =TI 所選的此產品重要文件
    找不到結果。請清除您的搜尋條件，然後再試一次。
    檢視所有 2
    類型 標題 日期
    * Data sheet LM3658 Dual Source USB/AC Li Chemistry Charger IC for Portable Applications datasheet (Rev. E) 2007年 3月 10日
    User guide AN-1517 LM3658 Evaluation Kit (Rev. E) 2013年 4月 30日

    設計與開發

    如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

    開發板

    LM3658SD-AEV — 適用於可攜式應用的雙來源 USB AC 鋰化學充電器 IC

    Recommended tool:
    bq24040 is the recommended alternative to the LM3658 devices. Please refer to the bq24040EVM for new device evaluation.

    The LM3658 is a single chip charger IC designed for hand-held applications. The LM3658 can safely charge and maintain a single cell Li-Ion/Polymer battery (...)

    使用指南: PDF
    TI.com 無法提供
    封裝 針腳 CAD 符號、佔位空間與 3D 模型
    WSON (DSC) 10 Ultra Librarian
    適用 TI 的評估品項標準條款與條件。

    訂購與品質

    內含資訊：
    • RoHS
    • REACH
    • 產品標記
    • 鉛塗層/球物料
    • MSL 等級/回焊峰值
    • MTBF/FIT 估算值
    • 材料內容
    • 認證摘要
    • 進行中持續性的可靠性監測
    內含資訊：
    • 晶圓廠位置
    • 組裝地點

    建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

    支援與培訓

    內含 TI 工程師技術支援的 TI E2E™ 論壇

    以英文檢視所有論壇主題

    內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

    若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

    影片