首頁 邏輯和電壓轉換 電壓轉換器及電平移位器 固定方向電壓轉換器
首頁
邏輯和電壓轉換
電壓轉換器及電平移位器
固定方向電壓轉換器
最新

TXV0106-Q1

現行

Automotive dual-supply fixed-direction six-channel voltage translator

立即訂購
產品規格表

TXV0106-Q1

現行
產品規格表 立即訂購

產品詳細資料

Technology family AVC Applications GPIO, JTAG, RGMII, SPI, UART Bits (#) 6 High input voltage (min) (V) 1.08 High input voltage (max) (V) 3.6 Vout (min) (V) 1.65 Vout (max) (V) 3.6 Data rate (max) (Mbps) 250 IOH (max) (mA) -12 IOL (max) (mA) 12 Supply current (max) (µA) 16 Features Output enable, Overvoltage tolerant inputs, Partial power down (Ioff), Vcc isolation Input type Standard CMOS Output type 3-State, Balanced CMOS, Push-Pull Rating Automotive Operating temperature range (°C) -40 to 125
Technology family AVC Applications GPIO, JTAG, RGMII, SPI, UART Bits (#) 6 High input voltage (min) (V) 1.08 High input voltage (max) (V) 3.6 Vout (min) (V) 1.65 Vout (max) (V) 3.6 Data rate (max) (Mbps) 250 IOH (max) (mA) -12 IOL (max) (mA) 12 Supply current (max) (µA) 16 Features Output enable, Overvoltage tolerant inputs, Partial power down (Ioff), Vcc isolation Input type Standard CMOS Output type 3-State, Balanced CMOS, Push-Pull Rating Automotive Operating temperature range (°C) -40 to 125
WQFN (BQB) 16 8.75 mm² 3.5 x 2.5

  • Configurable design allows each port to operate with a power supply range from 1.14V to 3.6V

  • Supports up to 500Mbps for 1.65V to 3.6V
  • AEC-Q100 qualified for automotive applications
  • Meets RGMII 2.0 timing specifications:
    • < 750ps rise and fall time
    • < ± 5 % duty cycle distortion
    • < ± 400ps channel to channel skew
    • Up to 250Mbps/channel
  • Integrated 10Ω damping output resistor to minimize signal reflections
  • High drive strength (up to 12mA at 3.6V)
  • Fully configurable symmetric dual-rail design
  • Optimal signal integrity performance with 390ps peak-to-peak jitter for 1.8V to 3.3V
  • Features VCC isolation and VCC disconnect
  • Ioff supports partial-power-down mode operation
  • Latch-up performance exceeds 100mA per JESD 78, Class II
  • ESD protection exceeds JESD 22:
    • 2000V Human-Body Model
    • 1000V Charged-Device Model
  • Low power consumption:
    • 10µA maximum (25°C)
    • 20µA maximum (–40°C to 125°C)
  • Operating temperature from –40°C to +125°C
  • Available in wettable flank WQFN (BQB) package

  • Configurable design allows each port to operate with a power supply range from 1.14V to 3.6V

  • Supports up to 500Mbps for 1.65V to 3.6V
  • AEC-Q100 qualified for automotive applications
  • Meets RGMII 2.0 timing specifications:
    • < 750ps rise and fall time
    • < ± 5 % duty cycle distortion
    • < ± 400ps channel to channel skew
    • Up to 250Mbps/channel
  • Integrated 10Ω damping output resistor to minimize signal reflections
  • High drive strength (up to 12mA at 3.6V)
  • Fully configurable symmetric dual-rail design
  • Optimal signal integrity performance with 390ps peak-to-peak jitter for 1.8V to 3.3V
  • Features VCC isolation and VCC disconnect
  • Ioff supports partial-power-down mode operation
  • Latch-up performance exceeds 100mA per JESD 78, Class II
  • ESD protection exceeds JESD 22:
    • 2000V Human-Body Model
    • 1000V Charged-Device Model
  • Low power consumption:
    • 10µA maximum (25°C)
    • 20µA maximum (–40°C to 125°C)
  • Operating temperature from –40°C to +125°C
  • Available in wettable flank WQFN (BQB) package

The TXV0106-Q1 is a 6-bit, dual-supply fixed-direction low-skew, low jitter voltage translation device. This device can be used for redriving, voltage translation and power isolation when implementing skew sensitive interface, such as RGMII between Ethernet MAC and PHY. The Ax I/O pins and enable pin (OE) are referenced to VCCA logic levels, and Bx I/O pins are referenced to VCCB logic levels. This device has improved channel-to-channel skew, duty cycle distortion and symmetric rise or fall timing for applications requiring strict timing conditions.

This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, thus preventing damaging current backflow through the device when it is powered down.

The VCC isolation feature is designed so that if either VCC supply is at or near 0V both ports will switch to a high-impedance state. This feature enables power isolation for communications across multiple MACs and PHYs, and is beneficial in situations where MACs and PHYs are powered up asynchronously preventing current backflow between devices.

The TXV0106-Q1 transmits data in a fixed direction from the A bus to the B bus. When OE is set to High, both Ax and Bx pins will be forced into a high-impedance state. See Device Functional Modes for a summary of the operation of the control logic.

The TXV0106-Q1 is a 6-bit, dual-supply fixed-direction low-skew, low jitter voltage translation device. This device can be used for redriving, voltage translation and power isolation when implementing skew sensitive interface, such as RGMII between Ethernet MAC and PHY. The Ax I/O pins and enable pin (OE) are referenced to VCCA logic levels, and Bx I/O pins are referenced to VCCB logic levels. This device has improved channel-to-channel skew, duty cycle distortion and symmetric rise or fall timing for applications requiring strict timing conditions.

This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, thus preventing damaging current backflow through the device when it is powered down.

The VCC isolation feature is designed so that if either VCC supply is at or near 0V both ports will switch to a high-impedance state. This feature enables power isolation for communications across multiple MACs and PHYs, and is beneficial in situations where MACs and PHYs are powered up asynchronously preventing current backflow between devices.

The TXV0106-Q1 transmits data in a fixed direction from the A bus to the B bus. When OE is set to High, both Ax and Bx pins will be forced into a high-impedance state. See Device Functional Modes for a summary of the operation of the control logic.
filter 尋找其它 固定方向電壓轉換器
下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
功能相同，但引腳輸出與所比較的裝置不同
最新 TXV0108-Q1 現行 車用雙電源方向控制八通道電壓轉換器 8 channel direction controlled version

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 11
類型 標題 日期
* Data sheet TXV0106-Q1 Automotive 6-Bit Fix Direction Low-Skew, Low-Jitter Voltage Translator or Buffer datasheet (Rev. B) PDF | HTML 2024年 4月 12日
Application note Schematic Checklist - A Guide to Designing With Fixed or Direction Control Translators PDF | HTML 2024年 10月 2日
Application note Schematic Checklist - A Guide to Designing with Auto-Bidirectional Translators PDF | HTML 2024年 7月 12日
Application note Understanding Transient Drive Strength vs. DC Drive Strength in Level-Shifters (Rev. A) PDF | HTML 2024年 7月 3日
Application brief Enabling AI Accelerators with Voltage Level Translation PDF | HTML 2024年 5月 1日
EVM User's guide TXV010xEVM Evaluation Module User's Guide PDF | HTML 2024年 2月 5日
Functional safety information TXV0106-Q1 Functional Safety, FIT Rate, Failure Mode Distribution and Pin FMA PDF | HTML 2024年 2月 1日
Application note Overcoming Design Challenges - Implementing High Performance Interfaces PDF | HTML 2023年 12月 12日
Application brief Solving Power Sequencing Challenges for Ethernet RGMII Communications PDF | HTML 2023年 10月 27日
Application brief Supporting Time and Skew Sensitive Interfaces with TI's TXV Level-Shifter PDF | HTML 2023年 10月 27日
Application brief Enabling Industrial and Automotive Ethernet RGMII Interfaces with Voltage Transl PDF | HTML 2023年 8月 2日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

14-24-NL-LOGIC-EVM — 適用於 14 針腳至 24 針腳無引線封裝的邏輯產品通用評估模組

14-24-NL-LOGIC-EVM 是一款靈活的評估模組 (EVM)，設計用途可支援任何具有 14 針腳至 24 針腳 BQA、BQB、RGY、RSV、RJW 或 RHL 封裝的邏輯或轉換裝置。

使用指南: PDF | HTML
TI.com 無法提供
開發板

TXV0106-EVM — TXV0106 評估模組

TXV0106 評估模組 (EVM) 是一個易於使用的平台，用於評估 TXV0106 產品的功能與性能。此 EVM 具有選用電路和跨接器，可針對不同應用來配置產品。此產品提供固定與方向控制低偏斜、低抖動電壓轉換的選項。輸出可透過專屬的輸出啟用 (OE) 控制功能來啟用及停用。
使用指南: PDF | HTML
TI.com 無法提供
模擬型號

TXV0106 IBIS Model

SCEM797.ZIP (44 KB) - IBIS Model
下載
封裝 針腳 CAD 符號、佔位空間與 3D 模型
WQFN (BQB) 16 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片