CD4059A
- Synchronous Programmable
N Counter:
N = 3 to 9999 or 15,999 - Presettable down-counter
- Fully static operation
- Mode-select control of initial decade counting function (
10,8,5,4,2)
- T2L drive capability
- Master preset initialization
- Latchable
N output
- Quiescent current specified to 15 volts
- Max. input leakage current of 1 µA at 15 volts, full package-temperature range
- 1 volt noise margin, full package-temperature range
- 5-V and 10-V parametric ratings
- Applications
- Communications digital frequency synthesizers: VHF, UHF, FM, AM, etc.
- Fixed or programmable frequency division
- "Time out" timer for consumer-application industrial controls
- Companion Application Note, ICAN-6374, "Application of the CMOS CD4059A Programmable Divide-by-N Counter in FM and Citizens Band Transceiver Digital Tuners"
Data sheet acquired from Harris Semiconductor.
CD4059 standard "A" Series types are divide-by-N down-counters that can be programmed to divide an input frequency by any number "N" from 3 to 15,999. The output signal is a pulse one clock-cycle wide occurring at a rate equal to the input frequency divided by N. This single output has TTL drive capability. The down-counter is preset by means of 16 jam inputs.
The three Mode-Select Inputs Ka, Kb, and Kc determine the modulus ("divide-by" number) of the first and last counting
sections in accordance with the truth table shown in Table 1. Every time the first (fastest) counting section goes through
one cycle, it reduces by 1 the number that has been preset (jammed) into the three decades of the intermediate counting
section and into the last counting section, which consists of flip-flops that are not needed for operating the first counting
section. For example, in the 2 mode, only one flip-flop is needed in the first counting
section. Therefore the last counting section has three flip-flops that can be preset to a maximum count of seven with a place
value of thousands. If
10 is desired for the first section, Ka is set 1, Kb to 1, and Kc
to 0. Jam Inputs J1, J2, J3, and J4 are used to preset the first counting section and there is no last counting section. The
intermediate counting section consists of three cascaded BCD decade (
10) counters
presettable by means of Jam Inputs J5 through J16.
The Mode-Select Inputs permit frequency-synthesizer channel separations of 10, 12.5, 20, 25, or 50 parts. These inputs set the maximum value of N at 9999 (when the first counting section divides by 5 or 10) or 15,999 (when the first counting section divides by 8, 4, or 2).
The three decades of the intermediate counting section can be preset to a binary 15 instead of a binary 9, while their
place values are still 1, 10, and 100, multiplied by the number of the N mode. For
example in the
8 mode, the number from which counting-down begins can be preset to:
- 3rd decade: 1500
- 2nd decade: 150
- 1st decade: 15
- Last counting section 1000
The total of these numbers (2665) times 8 equals 21,320. The first counting section can be preset to 7. Therefore,
21,327 is the maximum possible count in the 8 mode.
The highest count of the various modes is shown in the column entitled Extended Counter Range of Table 1. Control inputs Kb and Kc can be used to initiate and lock the counter in the "master preset" state. In this condition the flip-flops in the counter are preset in accordance with the jam inputs and the counter remains in that state as long as Kb and Kc both remain low. The counter begins to count down from the preset state when a counting mode other than the master preset mode is selected.
The counter should always be put in the master preset mode before the 5 mode is selected.
Whenever the master preset mode is used, control signals Kb=0 and Kc=0 must be applied for at least 3 full clock pulses.
After the Master Preset Mode inputs have been changed to one of the modes, the next
positive-going clock transition changes an internal flip-flop so that the countdown can begin at the second positive-going
clock transition. Thus, after an MP (Master Preset) mode, there is always one extra count before the output goes high.
Fig. 1 illustrates a total count of 3 (
8 mode). If the Master Preset mode is started
two clock cycles or less before an output pulse, the output pulse will appear at the time due. If the Master Preset Mode
is not used the counter jumps back to the "JAM" count when the output pulse appears.
A "1" on the Latch Enable input will cause the counter output to remain high once an output pulse occurs, and to remain in the high state until the latch input returns to "0". If the Latch Enable is "0", the output pulse will remain high for only 1 cycle of the clock-input signal.
As illustrated in the sample applications, this device is particularly advantageous in communication digital frequency synthesis (VHF, UHF, FM, AM, etc.) where programmable divide-by-"N" counters are an integral part of the synthesizer phase-locked-loop sub-system. The CD4059A can also be used to perform the synthesizer "Fixed Divide-by-R" counting function. It is also useful in general-purpose counters for instrumentation functions such as totalizers, production counters, and "time out" timers.
The CD4059B-series types are supplied in 24-lead dual-in-line plastic packages (E suffix), and 24-lead small-outline packages (M and M96 suffixes).
您可能會感興趣的類似產品
功能與所比較的裝置相似
技術文件
類型 | 標題 | 日期 | ||
---|---|---|---|---|
* | Data sheet | CD4059A TYPES datasheet (Rev. B) | 2003年 6月 20日 | |
Selection guide | Logic Guide (Rev. AB) | 2017年 6月 12日 | ||
Application note | Understanding and Interpreting Standard-Logic Data Sheets (Rev. C) | 2015年 12月 2日 | ||
User guide | LOGIC Pocket Data Book (Rev. B) | 2007年 1月 16日 | ||
Application note | Semiconductor Packing Material Electrostatic Discharge (ESD) Protection | 2004年 7月 8日 | ||
User guide | Signal Switch Data Book (Rev. A) | 2003年 11月 14日 | ||
Application note | Understanding Buffered and Unbuffered CD4xxxB Series Device Characteristics | 2001年 12月 3日 |
設計與開發
如需其他條款或必要資源,請按一下下方的任何標題以檢視詳細頁面 (如有)。
14-24-LOGIC-EVM — 適用於 14 針腳至 24 針腳 D、DB、DGV、DW、DYY、NS 和 PW 封裝的邏輯產品通用評估模組
14-24-LOGIC-EVM 評估模組 (EVM) 設計用於支援任何 14 針腳至 24 針腳 D、DW、DB、NS、PW、DYY 或 DGV 封裝的任何邏輯裝置。
封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
---|---|---|
SOIC (DW) | 24 | Ultra Librarian |
訂購與品質
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 認證摘要
- 進行中持續性的可靠性監測
- 晶圓廠位置
- 組裝地點