BQ24153A

Name: BQ24153A
Brand: TI
SKU: BQ24153A
Price: 2.45 USD

現行

具 OTG 和 Vovp=6.5V 的 I2C 1 芯 1.55A 降壓電池充電器

立即訂購

產品規格表

document-pdfAcrobat bq2415x Fully Integrated Switch-Mode One-Cell Li-Ion Charger With Full USB Compliance and USB-OTG Support datasheet (Rev. D) (英文) PDF | HTML

BQ24153A

現行

產品規格表

立即訂購

產品詳細資料

Number of series cells

1

Charge current (max) (A)

1.25

Vin (max) (V)

6

Cell chemistry

Li-Ion/Li-Polymer

Battery charge voltage (min) (V)

3.5

Battery charge voltage (max) (V)

4.44

Absolute max Vin (max) (V)

20

Control topology

Switch-Mode Buck

Control interface

I2C

Features

BAT temp thermistor monitoring (hot/cold profile)

Vin (min) (V)

4

Rating

Catalog

Operating temperature range (°C)

-40 to 85

Number of series cells

1

Charge current (max) (A)

1.25

Vin (max) (V)

6

Cell chemistry

Li-Ion/Li-Polymer

Battery charge voltage (min) (V)

3.5

Battery charge voltage (max) (V)

4.44

Absolute max Vin (max) (V)

20

Control topology

Switch-Mode Buck

Control interface

I2C

Features

BAT temp thermistor monitoring (hot/cold profile)

Vin (min) (V)

4

Rating

Catalog

Operating temperature range (°C)

-40 to 85

DSBGA (YFF)

20

3.96 mm² 1.8 x 2.2

Charge Faster than Linear Chargers
High-Accuracy Voltage and Current Regulation
- Input Current Regulation Accuracy: ±5% (100
  mA and 500 mA)
- Charge Voltage Regulation Accuracy: ±0.5%
  (25°C), ±1% (0°C to 125°C)
- Charge Current Regulation Accuracy: ±5%
Input Voltage Based Dynamic Power
Management (VIN DPM)
Bad Adaptor Detection and Rejection
Safety Limit Register for Maximum Charge
Voltage and Current Limiting
High-Efficiency Mini-USB/AC Battery Charger for
Single-Cell Li-Ion and Li-Polymer Battery Packs
20-V Absolute Maximum Input Voltage Rating
9-V Maximum Operating Input Voltage-
bq24156A/9
6-V Maximum Operating Input Voltage-
bq24153A/8
Built-In Input Current Sensing and Limiting
Integrated Power FETs for Up To 1.55-A Charge
Rate
Programmable Charge Parameters through I²C
Compatible Interface (up to 3.4 Mbps):
- Input Current Limit
- VIN DPM Threshold
- Fast-Charge/Termination Current
- Charge Regulation Voltage (3.5 V to 4.44 V)
- Low Charge Current Mode Enable/Disable
- Safety Timer with Reset Control
- Termination Enable/Disable
Support up to 1.55 A Charge Current Using 55-
mΩ Sensing Resistor
Synchronous Fixed-Frequency PWM Controller
Operating at 3 MHz With 0% to 99.5% Duty Cycle
Automatic High Impedance Mode for Low Power
Consumption
Robust Protection
- Reverse Leakage Protection Prevents Battery
  Drainage
- Thermal Regulation and Protection
- Input/Output Overvoltage Protection
Status Output for Charging and Faults
USB Friendly Boot-Up Sequence
Automatic Charging
Power Up System without Battery bq24158/9
Boost Mode Operation for USB OTG:
(bq24153A/8 only)
- Input Voltage Range (from Battery): 2.5 V to
  4.5 V
- Output for V_BUS: 5.05 V/ 200 mA
2.1 mm × 2 mm 20-Pin WCSP Package

APPLICATIONS

Mobile and Smart Phones
MP3 Players
Handheld Devices

Charge Faster than Linear Chargers
High-Accuracy Voltage and Current Regulation
- Input Current Regulation Accuracy: ±5% (100
  mA and 500 mA)
- Charge Voltage Regulation Accuracy: ±0.5%
  (25°C), ±1% (0°C to 125°C)
- Charge Current Regulation Accuracy: ±5%
Input Voltage Based Dynamic Power
Management (VIN DPM)
Bad Adaptor Detection and Rejection
Safety Limit Register for Maximum Charge
Voltage and Current Limiting
High-Efficiency Mini-USB/AC Battery Charger for
Single-Cell Li-Ion and Li-Polymer Battery Packs
20-V Absolute Maximum Input Voltage Rating
9-V Maximum Operating Input Voltage-
bq24156A/9
6-V Maximum Operating Input Voltage-
bq24153A/8
Built-In Input Current Sensing and Limiting
Integrated Power FETs for Up To 1.55-A Charge
Rate
Programmable Charge Parameters through I²C
Compatible Interface (up to 3.4 Mbps):
- Input Current Limit
- VIN DPM Threshold
- Fast-Charge/Termination Current
- Charge Regulation Voltage (3.5 V to 4.44 V)
- Low Charge Current Mode Enable/Disable
- Safety Timer with Reset Control
- Termination Enable/Disable
Support up to 1.55 A Charge Current Using 55-
mΩ Sensing Resistor
Synchronous Fixed-Frequency PWM Controller
Operating at 3 MHz With 0% to 99.5% Duty Cycle
Automatic High Impedance Mode for Low Power
Consumption
Robust Protection
- Reverse Leakage Protection Prevents Battery
  Drainage
- Thermal Regulation and Protection
- Input/Output Overvoltage Protection
Status Output for Charging and Faults
USB Friendly Boot-Up Sequence
Automatic Charging
Power Up System without Battery bq24158/9
Boost Mode Operation for USB OTG:
(bq24153A/8 only)
- Input Voltage Range (from Battery): 2.5 V to
  4.5 V
- Output for V_BUS: 5.05 V/ 200 mA
2.1 mm × 2 mm 20-Pin WCSP Package

APPLICATIONS

Mobile and Smart Phones
MP3 Players
Handheld Devices

The bq24153A/6A/8/9 is a compact, flexible, high-efficiency, USB-friendly switch-mode charge management device for single-cell Li-ion and Li-polymer batteries used in a wide range of portable applications. The charge parameters can be programmed through an I²C interface. The IC integrates a synchronous PWM controller, power MOSFETs, input current sensing, high-accuracy current and voltage regulation, and charge termination, into a small WCSP package.

The IC charges the battery in three phases: conditioning, constant current and constant voltage. The input current is automatically limited to the value set by the host. Charge is terminated based on battery voltage and user-selectable minimum current level. A safety timer with reset control provides a safety backup for I²C interface. During normal operation, The IC automatically restarts the charge cycle if the battery voltage falls below an internal threshold and automatically enters sleep mode or high impedance mode when the input supply is removed. The charge status can be reported to the host using the I²C interface. During the charging process, the IC monitors its junction temperature (TJ) and reduces the charge current once TJ increases to about 125°C. To support USB OTG device, bq24153A/8 can provide VBUS (5.05 V) by boosting the battery voltage. The IC is available in 20-pin WCSP package.

The bq24153A/6A/8/9 is a compact, flexible, high-efficiency, USB-friendly switch-mode charge management device for single-cell Li-ion and Li-polymer batteries used in a wide range of portable applications. The charge parameters can be programmed through an I²C interface. The IC integrates a synchronous PWM controller, power MOSFETs, input current sensing, high-accuracy current and voltage regulation, and charge termination, into a small WCSP package.

The IC charges the battery in three phases: conditioning, constant current and constant voltage. The input current is automatically limited to the value set by the host. Charge is terminated based on battery voltage and user-selectable minimum current level. A safety timer with reset control provides a safety backup for I²C interface. During normal operation, The IC automatically restarts the charge cycle if the battery voltage falls below an internal threshold and automatically enters sleep mode or high impedance mode when the input supply is removed. The charge status can be reported to the host using the I²C interface. During the charging process, the IC monitors its junction temperature (TJ) and reduces the charge current once TJ increases to about 125°C. To support USB OTG device, bq24153A/8 can provide VBUS (5.05 V) by boosting the battery voltage. The IC is available in 20-pin WCSP package.

filter

尋找其它電池充電器 IC

下載觀看有字幕稿的影片影片

技術文件

star

=TI 所選的此產品重要文件

找不到結果。請清除您的搜尋條件，然後再試一次。

檢視所有 3

	類型	標題		日期
*	Data sheet	bq2415x Fully Integrated Switch-Mode One-Cell Li-Ion Charger With Full USB Compliance and USB-OTG Support datasheet (Rev. D)	PDF \| HTML	2014年 1月 28日
	User guide	bq24153A/56A/57/58/59EVM Fully Integrated, Switch-Mode, One-Cell, Li-Ion Chgr (Rev. C)		2014年 5月 12日
	Application note	Building your own Battery Simulator		2013年 10月 14日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

驅動程式或資料庫

BQ2415XSW-LINUX — 適用於 BQ2415X 的 Linux 驅動程式

The Linux driver supports the BQ2415x series of fully integrated switch-mode one-cell Li-ion chargers. The Linux driver supports communication through the I2C bus and interfaces with the power supply sub-system.

Linux mainline status

Available in Linux mainline: Yes
Available through git.ti.com: (...)

View Options

支援軟體

BQ24153A_6A_7B_8_9EVM_SW — BQ24153A_9 EVM v1.4.0.1

With either the bq24153AEVM-697, bq24156AEVM-697, bq24157BEVM, bq24158EVM-697 or BQ24159EVM-697 connected to a Windows PC via the USB-TO-GPIO box, this software provides a PC-based GUI interface so that you can communicate with the IC using the I2C communication protocol.

支援產品和硬體

產品

電池充電器 IC

BQ24153A — 具 OTG 和 Vovp=6.5V 的 I2C 1 芯 1.55A 降壓電池充電器

BQ24156A — I2C 1 芯 1.55A 降壓電池充電器

BQ24158 — 開機時具 OTG 與無電池偵測的 I2C 1 芯 1.25A 降壓電池充電器

BQ24159 — 完全整合的切換模式單芯鋰離子充電器，完全符合 USB 規範。

硬體開發

開發板

BQ24157EVM-697 — BQ24157EVM-697 評估模組

BQ24158EVM-697 — 用於 BQ24158 完全整合切換模式單芯鋰離子充電器的評估模組

下載

封裝	針腳	CAD 符號、佔位空間與 3D 模型
DSBGA (YFF)	20	Ultra Librarian

適用 TI 的評估品項標準條款與條件。

BQ24153A

具 OTG 和 Vovp=6.5V 的 I2C 1 芯 1.55A 降壓電池充電器

BQ24153A

產品詳細資料

技術文件

設計與開發

BQ2415XSW-LINUX — 適用於 BQ2415X 的 Linux 驅動程式

BQ24153A_6A_7B_8_9EVM_SW — BQ24153A_9 EVM v1.4.0.1

支援產品和硬體

產品

電池充電器 IC

硬體開發

開發板

訂購與品質

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

影片系列

影片

下載選項

BQ24153A_6A_7B_8_9EVM_SW — BQ24153A_9 EVM v1.4.0.1

電池充電器 IC

硬體開發

版本資訊