TAS6582-Q1
- AEC-Q100 qualified for automotive applications
- Temperature grade 1: –40°C to +125°C, T A
- General operation
- 4.5-V to 45-V supply voltage, 50-V load dump
- Support for 1.8-V and 3.3-V I/O’s
- I 2C control with 8 address options
- <1.3 W idle power loss at 14.4 V, <8-uA max VBAT+PVDD shutdown loss
- Integrated DSP processing
- Class-H supply voltage control
- Thermal monitoring and foldback
- Clip detection, PVDD monitoring and foldback
- Output current sensing by channel via I 2S/TDM
- No need for external circuitry
- Real-time load diagnostics
- Monitor output conditions while playing audio
- Open load, Shorted load, Short-to-power, Short-to-ground detection
- DC and AC Standby load diagnostics
- Audio inputs
- 2 channel I 2S or 4-16 channel TDM input
- Input sample rates: 44.1, 48, 96, 192 kHz
- Secondary low latency path, >70% reduced signal delay at 48 kHz
- Audio outputs
- 2-channel bridge-tied load (BTL), configurable 1-channel parallel BTL (PBTL)
- 384-kHz to 2.1-MHz configurable output switching frequency
- Up to 10-A channel output current
- 400-VA peak BTL output power
- 118 W (45 V, 8 Ω, 1% THD, BTL)
- 215 W (45 V, 4 Ω, 1% THD, BTL)
- Audio Performance
- THD+N 0.03% (8 Ω, 1 W, 1 kHz)
- 111 dB SNR
- 37 µV (14.4 V), 80 µV (45 V) output noise
- Protection
- Output short protection
- DC offset, undervoltage and overvoltage
- Configurable overtemperature warning and individual channel shutdown
- I 2C temperature and supply voltage readout
- Easily meet CISPR25-L5 EMC specification
- Advanced spread-spectrum
The TAS6582-Q1 is a two-channel, digital-input, high-voltage, Class-D audio amplifier that supports up to 45-V supply voltage. In combination with up to 10-A output current, this device delivers maximum output power and high fidelity audio in high and low impedance loads. The device provides two channels at 118 W (45 V, 8 Ω, 1% THD, BTL) and 215 W (45 V, 4 Ω, 1% THD, BTL).
The TAS6582-Q1 integrates DC and AC load diagnostics to determine the status of the connected loads before enabling the output stage. During audio playback, the status can be monitored through output current sense which is available for each channel and reports the measurement to a host processor through TDM with minimal delay. The device monitors the output load condition while playing audio using real-time load diagnostics which operate independent from host and audio input.
To optimize system efficiency, the integrated DSP of the TAS6582-Q1 enables Class-H envelope tracking control, eliminating the need for development of complex tracking software and making local boost voltage control possible without the need for an external microcontroller.
The TAS6582-Q1 device features an additional low-latency signal path for each channel, providing up to 70% faster signal processing at 48 kHz which enables time-sensitive Active Noise Cancellation (ANC), Road Noise Cancellation (RNC) applications.
The device is offered in a 64-pin QFP package with the exposed thermal pad up.
索取更多資訊：
提供完整產品規格表、PurePath™ Console 3、TAS6582-Q1 GUI和其他設計資源。立即索取
您可能會感興趣的類似產品
引腳對引腳且具備與所比較裝置相同的功能
技術文件
| 類型 | 標題 | 日期 | ||
|---|---|---|---|---|
| * | Data sheet | TAS6582-Q1 - 45-V, 10-A Digital Input 2-Channel Automotive Class-D Audio Amplifier with Current Sense and Real-time Load Diagnostics datasheet | PDF | HTML | 2023年 6月 12日 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| HTQFP (PHD) | 64 | Ultra Librarian |
訂購與品質
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 認證摘要
- 進行中持續性的可靠性監測
- 晶圓廠位置
- 組裝地點
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。