SLAT163 July   2024 AFE43902-Q1 , AFE439A2 , AFE53902-Q1 , AFE539A4 , AFE539F1-Q1 , AFE639D2 , DAC43204 , DAC43401 , DAC43401-Q1 , DAC43701 , DAC43701-Q1 , DAC43901-Q1 , DAC43902-Q1 , DAC53001 , DAC53002 , DAC53004 , DAC53004W , DAC53202 , DAC53204 , DAC53204-Q1 , DAC53204W , DAC53401 , DAC53401-Q1 , DAC53701-Q1 , DAC539E4W , DAC539G2-Q1 , DAC63001 , DAC63002 , DAC63004 , DAC63004W , DAC63202 , DAC63202W , DAC63204 , DAC63204-Q1 , DAC63204W

 

  1.   1
  2.   Abstract
  3.   Trademarks
  4. 1What is a Smart DAC?
  5. 2What is a Smart Analog Front End (AFE)?
  6. 3Smart DAC selection guide
  7. 4Smart AFE Selection Guide
  8. 5Applications
    1. 5.1 Lightning
      1. 5.1.1 Light Emitting Diode (LED) Biasing and Linear Fade-In Fade-Out
      2. 5.1.2 LED Biasing With LED Driver
      3. 5.1.3 Analog Thermal Foldback
        1. 5.1.3.1 Single Slope Thermal Foldback
        2. 5.1.3.2 Multi-Slope Thermal Foldback
      4. 5.1.4 Logarithmic Fade-In/Fade-Out
      5. 5.1.5 LED Sequencing
    2. 5.2 Control
      1. 5.2.1 Voltage Margining and Scaling With Voltage Output Smart DAC
      2. 5.2.2 Thermoelectric Cooling (TEC) Control
        1. 5.2.2.1 TEC Control Using DC/DC Driver
        2. 5.2.2.2 TEC control using h-Bridge driver
      3. 5.2.3 Analog Power Control (APC) of a Laser
      4. 5.2.4 Constant Power Control
    3. 5.3 Microcontroller Independent Fault Management and Communication
      1. 5.3.1 Programmable Comparator Using Smart DAC
      2. 5.3.2 GPI-to-PWM
      3. 5.3.3 If-Then-Else Logic
    4. 5.4 Driver
      1. 5.4.1 Lens Positioning Control for Camera Module Auto-Focus and Image Stabilization
      2. 5.4.2 Laser Drive
    5. 5.5 Miscellaneous Smart DAC Applications
      1. 5.5.1 Software-less Medical Alarm Generation
      2. 5.5.2 555 Timer

5.1.5 LED Sequencing

Smart DAC is able to create sequencing animation for LED or an array of LEDs for applications such as a turn indicator. Turn indicator requires the LED arrays to light up with a specific delay and then to turn off after certain time. Normally to set up this behavior the software is utilized. Smart DAC can implement such application without the need for any software.

AFE43901-Q1 (2 PWM channels) or AFE43902-Q1 (4 PWM channels) control the LED driver. After receiving a trigger signal, each PWM channel gets activated with a predefined delay. The delay is completely customizable through the device internal registers. In cases where more PWM channels are desired, the AFE43902-Q1 can be cascaded by connecting TRIG-OUT pin to TRIG-IN pin of the next device. All of the configurations can be stored in the device non-volatile memory for software free operation.

Table 5-6 Design Implementation
Hardware Block DiagramFigure 5-6 Hardware Block Diagram
Design BenefitsSuggested device
  • Professor-less logarithmic fading of LED
  • Fading trigger
  • Slew rate to control the speed
  • PWM or voltage output
  • Non-volatile memory to store all configurations
End EquipmentDesign help
  • Indication LED
  • Turn indicator