BQ25125
- Increases system operation time between charges
- Configurable 300-mA buck regulator (1.8 V default)
- 700-nA (typical) Iq with buck converter enabled (No Load)
- Configurable load switch or 100-mA LDO output (1.8 V default)
- Up to 300-mA charge current for fast charging
- 0.5% Accurate battery voltage regulation (configurable from 3.6 V to 4.65 V in 10-mV steps)
- Configurable termination current down to 500 µA
- Simple voltage based battery monitor
- Watchdog timer enabled by default
- VDPPM Loop disabled
- VINDPM Disabled by default to support low voltage charging
- Highly integrated solution with small footprint
- 2.5 mm x 2.5 mm WCSP Package and 6 external components for minimal solution
- Push-button wake-up and reset with adjustable timers
- Power path management for powering the system and charging the battery
- Power path management enables <50 nA ship mode battery quiescent current for longest shelf life
- Battery charger operates from 3.4 V – 5.5 VIN (5.5-V OVP / 20-V tolerant)
- Dedicated pins for input current limit, charge current, termination current, and status output
- I2C Communication control
- Charge voltage and current
- Termination threshold
- Input current limit
- VINDPM Threshold
- Timer options
- Load switch control
- Controls for interrupts for faults and status
- System output voltage adjustment
- LDO Output voltage adjustment
- Safety-Related Certification:
- TUV IEC 62368-1 Certification
The BQ25125 is a highly integrated battery charge management IC that integrates the most common functions for wearable devices: Linear charger, regulated output, load switch, manual reset with timer, and battery voltage monitor. The integrated buck converter is a high efficiency, low IQ switcher using DCS-Control™ that extends light load efficiency down to 10-µA load currents.
The low quiescent current during operation and shutdown enables maximum battery life. The device supports charge currents from 5 mA to 300 mA. The input current limit, charge current, buck converter output voltage, LDO output voltage, and other parameters are programmable through the I2C interface.
The battery is charged using a standard Li-Ion charge profile with three phases: precharge, constant current and constant voltage. A voltage-based JEITA compatible battery pack thermistor monitoring input (TS) is included that monitors battery temperature and automatically changes charge parameters to prevent the battery from charging outside of its safe temperature range. The charger is optimized for 5-V USB input, with 20-V tolerance to withstand line transients. The buck converter is run from the input or battery. When in battery only mode, the device can run from a battery up to 4.65 V.
A configurable load switch allows system optimization by disconnecting infrequently used devices. The manual reset with timer allows multiple different configuration options for wake are reset optimization. A simple voltage based monitor provides battery level information to the host in 2% increments from 60% to 100% of the programmed V(BATREG).
기술 자료
| 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | BQ25125 Low IQ Highly Integrated Battery Charge Management Solution For Wearables and IoT datasheet (Rev. A) | PDF | HTML | 2021/01/20 |
| Technical article | 3 ways low-Iq technologies extend battery life without compromising system performance | PDF | HTML | 2024/01/05 | |
| Application note | Implementing 2-V Charge Inhibition | PDF | HTML | 2023/05/31 | |
| White paper | 저전력 애플리케이션의 저 IQ 문제점 극복 (Rev. B) | PDF | HTML | 2023/04/19 | |
| Application note | BQ2512x Frequently Asked Questions | 2021/11/22 | ||
| Technical article | When to use rechargeable batteries in small battery applications | PDF | HTML | 2019/10/01 | |
| Technical article | Pull the tab: How to implement ship mode in your lithium-ion battery design | PDF | HTML | 2019/02/20 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
BQ25120AEVM — 웨어러블 및 히어러블용 700nA 저 Iq 고집적 배터리 충전 관리 평가 모듈
EV2400 — 배터리 연료(가스) 게이지용 USB 기반 PC 인터페이스 평가 모듈
The EV2400 EVM interface board enables an IBM-compatible or other type PC (with the required driver for its particular platform) to communicate with the Texas Instruments SMBus or I2C interface gas gauges via a Universal Serial Bus (USB) port. In addition to this board, PC software is required to (...)
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| DSBGA (YFP) | 25 | Ultra Librarian |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.