首頁 馬達驅動器 有刷 DC (BDC) 馬達驅動器
首頁
馬達驅動器
有刷 DC (BDC) 馬達驅動器

DRV8876-Q1

現行

具有整合電流感測和電流感測回饋的車用 40-V、3.5-A H 橋馬達驅動器

立即訂購
產品規格表

DRV8876-Q1

現行
產品規格表 立即訂購

產品詳細資料

Number of full bridges 1 Vs (min) (V) 4.5 Vs ABS (max) (V) 40 Peak output current (A) 3.5 RDS(ON) (HS + LS) (mΩ) 700 Sleep current (µA) 0.75 Control mode Independent 1/2-Bridge, PH/EN, PWM Control interface Hardware (GPIO) Features Current sense Amplifier, Integrated Current Sensing Rating Automotive TI functional safety category Functional Safety-Capable Operating temperature range (°C) -40 to 125
Number of full bridges 1 Vs (min) (V) 4.5 Vs ABS (max) (V) 40 Peak output current (A) 3.5 RDS(ON) (HS + LS) (mΩ) 700 Sleep current (µA) 0.75 Control mode Independent 1/2-Bridge, PH/EN, PWM Control interface Hardware (GPIO) Features Current sense Amplifier, Integrated Current Sensing Rating Automotive TI functional safety category Functional Safety-Capable Operating temperature range (°C) -40 to 125
HTSSOP (PWP) 16 32 mm² 5 x 6.4
  • AEC-Q100 qualified for automotive applications:
    • Temperature grade 1: –40°C to +125°C, TA
  • Functional Safety-Capable
  • N-channel H-bridge motor driver
    • Drives one bidirectional brushed DC motor
    • Two unidirectional brushed DC motors
    • Other resistive and inductive loads
  • 4.5-V to 37-V operating supply voltage range
  • Pin to pin RDS(on) variants
    • DRV8874-Q1: 200-mΩ (High-Side + Low-Side)
    • DRV8876-Q1: 700-mΩ (High-Side + Low-Side)
  • High output current capability
  • Integrated current sensing and regulation
  • Proportional current output (IPROPI)
  • Selectable current regulation (IMODE)
    • Cycle-by-cycle or fixed off time
  • Selectable input control modes (PMODE)
    • PH/EN and PWM H-bridge control modes
    • Independent half-bridge control mode
  • Supports 1.8-V, 3.3-V, and 5-V logic inputs
  • Ultra low-power sleep mode
    • <1-µA @ VVM = 24-V, TJ = 25°C
  • Spread spectrum clocking for low electromagnetic interference (EMI)
  • Integrated protection features
    • Undervoltage lockout (UVLO)
    • Charge pump undervoltage (CPUV)
    • Overcurrent protection (OCP)
      • Automatic retry or outputs latched off (IMODE)
    • Thermal shutdown (TSD)
    • Automatic fault recovery
    • Fault indicator pin (nFAULT)
  • AEC-Q100 qualified for automotive applications:
    • Temperature grade 1: –40°C to +125°C, TA
  • Functional Safety-Capable
  • N-channel H-bridge motor driver
    • Drives one bidirectional brushed DC motor
    • Two unidirectional brushed DC motors
    • Other resistive and inductive loads
  • 4.5-V to 37-V operating supply voltage range
  • Pin to pin RDS(on) variants
    • DRV8874-Q1: 200-mΩ (High-Side + Low-Side)
    • DRV8876-Q1: 700-mΩ (High-Side + Low-Side)
  • High output current capability
  • Integrated current sensing and regulation
  • Proportional current output (IPROPI)
  • Selectable current regulation (IMODE)
    • Cycle-by-cycle or fixed off time
  • Selectable input control modes (PMODE)
    • PH/EN and PWM H-bridge control modes
    • Independent half-bridge control mode
  • Supports 1.8-V, 3.3-V, and 5-V logic inputs
  • Ultra low-power sleep mode
    • <1-µA @ VVM = 24-V, TJ = 25°C
  • Spread spectrum clocking for low electromagnetic interference (EMI)
  • Integrated protection features
    • Undervoltage lockout (UVLO)
    • Charge pump undervoltage (CPUV)
    • Overcurrent protection (OCP)
      • Automatic retry or outputs latched off (IMODE)
    • Thermal shutdown (TSD)
    • Automatic fault recovery
    • Fault indicator pin (nFAULT)

The DRV8876-Q1 is an integrated motor driver with N-channel H-bridge, charge pump, current sensing and proportional output, current regulation, and protection circuitry. The charge pump improves efficiency by supporting N-channel MOSFET half bridges and 100% duty cycle driving. The family of devices come in pin-to-pin RDS(on) variants to support different loads with minimal design changes.

An internal current mirror architecture on the IPROPI pin implements current sensing and regulation. This eliminates the need for a large power shunt resistor, saving board area and reducing system cost. The IPROPI current-sense output allows a microcontroller to detect motor stall or changes in load conditions. Using the external voltage reference pin, VREF, these devices can regulate the motor current during start-up and high-load events without interaction from a microcontroller.

A low-power sleep mode achieves ultra-low quiescent current draw by shutting down most of the internal circuitry. Internal protection features include supply undervoltage lockout, charge pump undervoltage, output overcurrent, and device overtemperature. Fault conditions are indicated on nFAULT.

View our full portfolio of brushed motor drivers on ti.com.

The DRV8876-Q1 is an integrated motor driver with N-channel H-bridge, charge pump, current sensing and proportional output, current regulation, and protection circuitry. The charge pump improves efficiency by supporting N-channel MOSFET half bridges and 100% duty cycle driving. The family of devices come in pin-to-pin RDS(on) variants to support different loads with minimal design changes.

An internal current mirror architecture on the IPROPI pin implements current sensing and regulation. This eliminates the need for a large power shunt resistor, saving board area and reducing system cost. The IPROPI current-sense output allows a microcontroller to detect motor stall or changes in load conditions. Using the external voltage reference pin, VREF, these devices can regulate the motor current during start-up and high-load events without interaction from a microcontroller.

A low-power sleep mode achieves ultra-low quiescent current draw by shutting down most of the internal circuitry. Internal protection features include supply undervoltage lockout, charge pump undervoltage, output overcurrent, and device overtemperature. Fault conditions are indicated on nFAULT.

View our full portfolio of brushed motor drivers on ti.com.
filter 尋找其它 有刷 DC (BDC) 馬達驅動器
下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
引腳對引腳且具備與所比較裝置相同的功能
DRV8874-Q1 現行 具整合電流感測和電流感測回饋的車用 40-V、6-A 全橋馬達驅動器 Pin-to-pin compatible but higher current
功能相同，但引腳輸出與所比較的裝置不同
DRV8243-Q1 現行 具有整合式電流感測與回饋的車用 40-V、12-A 全橋驅動器 Higher current capabilities
DRV8873-Q1 現行 Automotive, current sensing 40V, 10A H-bridge motor driver with integrated current feedback Higher current capabilities

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 11
類型 標題 日期
* Data sheet DRV8876-Q1 H-Bridge Motor Driver With Integrated Current Sense and Regulation datasheet (Rev. B) PDF | HTML 2020年 12月 16日
Application brief Advantages of Integrated Current Sensing (Rev. B) PDF | HTML 2022年 6月 20日
Application note Using DRV to Drive Solenoids (Rev. A) PDF | HTML 2022年 4月 24日
Application note Methods to Configure Current Regulation for Brushed and Stepper Motors (Rev. B) PDF | HTML 2021年 1月 19日
Technical article How analog integration simplifies automotive body motor controller designs PDF | HTML 2020年 10月 23日
Technical article How to efficiently drive 12-V and 24-V engine loads in automotive systems PDF | HTML 2020年 7月 9日
Functional safety information DRV8876-Q1 Functional Safety, FIT Rate, Failure Mode Distribution and Pin FMA PDF | HTML 2020年 5月 28日
User guide DRV8876/74-Q1 Evaluation Module (Rev. C) 2019年 12月 6日
Application note Protecting Automotive Motor Drive Systems from Reverse Polarity Conditions (Rev. A) 2019年 2月 19日
Application note PowerPAD™ Thermally Enhanced Package (Rev. H) 2018年 7月 6日
Application brief PowerPAD™ Made Easy (Rev. B) 2004年 5月 12日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

DRV8876-Q1EVM — DRV8876-Q1 單全橋馬達驅動器評估模組

The DRV8876-Q1 evaluation module (EVM) allows easy evaluation of the DRV8876-Q1 device. The DRV8876-Q1 device is an integrated H-bridge driver for brushed DC and solenoid applications. The evaluation module allows the device to be configured for PWM, phase/enable, or independent half-bridge control (...)

使用指南: PDF
TI.com 無法提供
模擬型號

DRV8876-Q1 PSpice Transient Simulation (Rev. A)

SLVMCQ2A.ZIP (113 KB) - PSpice Model
下載
封裝 針腳 CAD 符號、佔位空間與 3D 模型
HTSSOP (PWP) 16 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片