首頁 音訊 音訊放大器 喇叭放大器
首頁
音訊
音訊放大器
喇叭放大器

TAS6422E-Q1

現行

車用 75W、2MHz、2 通道 4.5V 至 26.4V 數位輸入 D 類音訊放大器

立即訂購
產品規格表

TAS6422E-Q1

現行
產品規格表 立即訂購

產品詳細資料

Audio input type Digital Input Architecture Class-D Speaker channels (max) Stereo Rating Automotive Power stage supply (max) (V) 26.4 Power stage supply (min) (V) 4.5 Load (min) (Ω) 2 Output power (W) 75 THD + N at 1 kHz (%) 0.02 Iq (typ) (mA) 84 Control interface I2C Closed/open loop Closed Analog supply (min) (V) 4.5 Analog supply voltage (max) (V) 26.4 Sampling rate (max) (kHz) 96 PSRR (dB) 75 Operating temperature range (°C) -40 to 125
Audio input type Digital Input Architecture Class-D Speaker channels (max) Stereo Rating Automotive Power stage supply (max) (V) 26.4 Power stage supply (min) (V) 4.5 Load (min) (Ω) 2 Output power (W) 75 THD + N at 1 kHz (%) 0.02 Iq (typ) (mA) 84 Control interface I2C Closed/open loop Closed Analog supply (min) (V) 4.5 Analog supply voltage (max) (V) 26.4 Sampling rate (max) (kHz) 96 PSRR (dB) 75 Operating temperature range (°C) -40 to 125
HSSOP (DKQ) 56 190.647 mm² 18.42 x 10.35
  • AEC-Q100 Qualified for automotive applications
    • Temperature grade 1: –40°C to +125°C TA
  • Advanced load diagnostics
    • DC Diagnostics run without input clocks
    • AC Diagnostic for tweeter detection with impedance and phase response
  • Easily meets CISPR25-L5 EMC specifications
  • Audio inputs
    • 2 Channel I2S or 4/8-channel TDM input
    • Input sample rates: 44.1 kHz, 48 kHz, 96 kHz
    • Input formats: 16-bit to 32-bit I2S, and TDM
  • Audio Outputs
    • Two-channel bridge-tied load (BTL)
    • Single-channel parallel BTL (PBTL)
    • Up to 2.1 MHz output switching frequency
    • 45 W, 10% THD+N Into 2 Ω at 14.4 V BTL
    • 75 W, 10% THD+N Into 4 Ω at 25 V BTL
    • 150W, 10% THD+N Into 2 Ω at 25V PBTL
  • Audio performance into 4 Ω at 14.4 V BTL
    • THD+N < 0.02% at 1 W
    • 42 µVRMS output noise
    • –90 dB crosstalk
  • Load diagnostics
    • Output open and shorted load
    • Output-to-battery or ground shorts
    • Line output detection up to 6 kΩ
    • Host-independent operation
  • Protection
    • Output current limiting and short protection
    • 40 V Load dump
    • Open ground and power tolerant
    • DC offset
    • Over-temperature
    • Undervoltage and overvoltage
  • General Operation
    • 4.5 V to 18 V supply voltage
    • I2C Control with 4 address options
    • Latched & Non-Latched Clip Detect
    • Enhanced EMI Management
  • AEC-Q100 Qualified for automotive applications
    • Temperature grade 1: –40°C to +125°C TA
  • Advanced load diagnostics
    • DC Diagnostics run without input clocks
    • AC Diagnostic for tweeter detection with impedance and phase response
  • Easily meets CISPR25-L5 EMC specifications
  • Audio inputs
    • 2 Channel I2S or 4/8-channel TDM input
    • Input sample rates: 44.1 kHz, 48 kHz, 96 kHz
    • Input formats: 16-bit to 32-bit I2S, and TDM
  • Audio Outputs
    • Two-channel bridge-tied load (BTL)
    • Single-channel parallel BTL (PBTL)
    • Up to 2.1 MHz output switching frequency
    • 45 W, 10% THD+N Into 2 Ω at 14.4 V BTL
    • 75 W, 10% THD+N Into 4 Ω at 25 V BTL
    • 150W, 10% THD+N Into 2 Ω at 25V PBTL
  • Audio performance into 4 Ω at 14.4 V BTL
    • THD+N < 0.02% at 1 W
    • 42 µVRMS output noise
    • –90 dB crosstalk
  • Load diagnostics
    • Output open and shorted load
    • Output-to-battery or ground shorts
    • Line output detection up to 6 kΩ
    • Host-independent operation
  • Protection
    • Output current limiting and short protection
    • 40 V Load dump
    • Open ground and power tolerant
    • DC offset
    • Over-temperature
    • Undervoltage and overvoltage
  • General Operation
    • 4.5 V to 18 V supply voltage
    • I2C Control with 4 address options
    • Latched & Non-Latched Clip Detect
    • Enhanced EMI Management

The TAS6422E-Q1 device is a two-channel digital-input Class-D audio amplifier that implements a 2.1 MHz PWM switching frequency enabling a cost-optimized solution in a very small PCB size, full operation down to 4.5 V for start/stop events, and exceptional sound quality with up to 40 kHz audio bandwidth.

The devices adds EMI management features including spread-spectrum to assist in system level EMI challenges.

The output switching frequency can be set either above the AM band, which eliminates AM-band interferences and reduces output filtering and cost, or below the AM band to optimize efficiency.

The device has a built-in load diagnostic function for detecting and diagnosing misconnected outputs as well as detection of AC-coupled tweeters to help to reduce test time during the manufacturing process.

The TAS6422E-Q1 Class-D audio amplifier is designed for use in automotive head units and external amplifier modules. For pin compatible one, two and four-channel devices see the the Device Options table.

The TAS6422E-Q1 device is a two-channel digital-input Class-D audio amplifier that implements a 2.1 MHz PWM switching frequency enabling a cost-optimized solution in a very small PCB size, full operation down to 4.5 V for start/stop events, and exceptional sound quality with up to 40 kHz audio bandwidth.

The devices adds EMI management features including spread-spectrum to assist in system level EMI challenges.

The output switching frequency can be set either above the AM band, which eliminates AM-band interferences and reduces output filtering and cost, or below the AM band to optimize efficiency.

The device has a built-in load diagnostic function for detecting and diagnosing misconnected outputs as well as detection of AC-coupled tweeters to help to reduce test time during the manufacturing process.

The TAS6422E-Q1 Class-D audio amplifier is designed for use in automotive head units and external amplifier modules. For pin compatible one, two and four-channel devices see the the Device Options table.
filter 尋找其它 喇叭放大器
下載 觀看有字幕稿的影片 影片

索取更多資訊

提供 PurePath™ Console 3、TAS6422E-Q1 GUI 和其他設計資源。立即索取

您可能會感興趣的類似產品

open-in-new 比較替代產品
可直接投入的替代產品，相較於所比較的裝置，具備升級功能
TAS6421-Q1 現行 具有負載突降的車用 75W、2MHz、單通道 4.5 至 26.4V 數位輸入 D 類音訊放大器 TAS6421-Q1 is our 1-channel automotive Class-D digital input amplifier which implements 2.1-MHz switching frequency.
TAS6424E-Q1 現行 汽車、75-W、2-MHz、四通道、4.5 至 26.4-V 數位輸入 D 類音訊放大器 TAS6424E-Q1 is our 4-channel automotive Class-D digital input amplifier which implements 2.1MHz switching frequency.

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 2
類型 標題 日期
* Data sheet TAS6422E-Q1 45-W, 2-MHz Digital Input 2-Channel Automotive Class-D Audio Amplifi datasheet (Rev. A) 2020年 11月 16日
EVM User's guide TAS6422E-Q1 EVM User's Guide (Rev. A) 2021年 2月 1日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TAS6422EQ1EVM — 具有 I2C 診斷評估模組的 2MHz 2 通道數位輸入 D 類音訊放大器

TAS6422EQ1EVM 評估模組 (EVM) 展示了用於車載資訊娛樂系統的 2MHz、4 通道數位輸入 D 類音訊解決方案。TAS6422E 的 2.1MHz 切換頻率可讓使用者能夠大幅減小電感器尺寸，並將整體系統成本最佳化。TAS6422E 為每通道提供 25W (10% THD+N)，在 14.4V 電源時為 4Ω，且其 4.5V 至 26V 的廣泛供應電壓能力適用於音響主機和外部放大器系統，同時在啟停低電壓瞬態事件期間提供一流的效能。TAS6422E 採用展頻技術，符合 CISPR25 Class 5 EMI 規範標準，並整合了 I2C 診斷和保護。
使用指南: PDF
TI.com 無法提供
模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
要求
封裝 針腳 CAD 符號、佔位空間與 3D 模型
HSSOP (DKQ) 56 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片