AEC-Q100 qualified with the following results:
- Device temperature grade 0: –40°C to +160°C ambient operating temperature
High resolution and accuracy of ≤ 1 degree at rotational speeds up to 480,000 RPM
Differential signal paths with sine and cosine outputs supporting a wide dynamic input range
Integrated analog front-end IC for contact-less, inductive position sensors for absolute rotary position from 0° to 360°
Supports operation in harsh environments; immune to stray magnetic fields, dirt, and contamination
No magnets required
Input supply operating modes: 5 V and 3.3 V
Operating current: 22 mA (maximum)
Integrated LC oscillator in the 2.4-MHz to 5-MHz band to excite the inductive sensor coil
Differential output drivers with high-voltage protection and large capacitive load capability
Automatic and manual gain control to maximize dynamic range of output drivers
Built-in sensor and supply diagnostics
Reverse voltage and overvoltage protection on input supply and output pins from –15 V to 30 V
For enhanced functional safety and diagnostics, see LDC5072-Q1
Supports redundant mode
Package: TSSOP-16 (5.00 mm x 4.40 mm)

AEC-Q100 qualified with the following results:
- Device temperature grade 0: –40°C to +160°C ambient operating temperature
High resolution and accuracy of ≤ 1 degree at rotational speeds up to 480,000 RPM
Differential signal paths with sine and cosine outputs supporting a wide dynamic input range
Integrated analog front-end IC for contact-less, inductive position sensors for absolute rotary position from 0° to 360°
Supports operation in harsh environments; immune to stray magnetic fields, dirt, and contamination
No magnets required
Input supply operating modes: 5 V and 3.3 V
Operating current: 22 mA (maximum)
Integrated LC oscillator in the 2.4-MHz to 5-MHz band to excite the inductive sensor coil
Differential output drivers with high-voltage protection and large capacitive load capability
Automatic and manual gain control to maximize dynamic range of output drivers
Built-in sensor and supply diagnostics
Reverse voltage and overvoltage protection on input supply and output pins from –15 V to 30 V
For enhanced functional safety and diagnostics, see LDC5072-Q1
Supports redundant mode
Package: TSSOP-16 (5.00 mm x 4.40 mm)

LDC5071-Q1 is a high-speed and accurate inductive sensor used for measuring absolute linear and rotary position in automotive and industrial applications. The device is designed to interface to three inductive sensing coils that are typically on the printed circuit board. One of the coils is connected to the exciter circuit of the LDC5071-Q1 and acts as a transmitter, and the other two secondary coils are used as receivers. The transmitter coil induces a voltage in the secondary coils, which is a function of the conductive target above the sensor coils. The demodulated signals which are produced during LDC5071-Q1 operation are then provided through the differential signal path with sine and cosine outputs.

The LDC5071-Q1 has multiple supply options, 5-V or 3.3-V, to suit different design options and can be connected to a microcontroller to calculate the rotary angle. The manual and automatic gain control (AGC) of the LDC5071-Q1 can be used to control and maximize the dynamic range of the outputs.

The device offers robust protection features to support and monitor signals and overall device operation for a seamless systems protection. The LDC5071-Q1 supports overvoltage, reverse battery and current protection on short to high voltage on output pins. In addition, the device provides immunity against motor noise and can filter out-of-band low- and high-frequency noise.

LDC5071-Q1 is a high-speed and accurate inductive sensor used for measuring absolute linear and rotary position in automotive and industrial applications. The device is designed to interface to three inductive sensing coils that are typically on the printed circuit board. One of the coils is connected to the exciter circuit of the LDC5071-Q1 and acts as a transmitter, and the other two secondary coils are used as receivers. The transmitter coil induces a voltage in the secondary coils, which is a function of the conductive target above the sensor coils. The demodulated signals which are produced during LDC5071-Q1 operation are then provided through the differential signal path with sine and cosine outputs.

The LDC5071-Q1 has multiple supply options, 5-V or 3.3-V, to suit different design options and can be connected to a microcontroller to calculate the rotary angle. The manual and automatic gain control (AGC) of the LDC5071-Q1 can be used to control and maximize the dynamic range of the outputs.

The device offers robust protection features to support and monitor signals and overall device operation for a seamless systems protection. The LDC5071-Q1 supports overvoltage, reverse battery and current protection on short to high voltage on output pins. In addition, the device provides immunity against motor noise and can filter out-of-band low- and high-frequency noise.

filter

Andere Induktive Sensor-AFEs suchen

Herunterladen Video mit Transkript ansehen Video

Technische Dokumentation

star

=Von TI ausgewählte Top-Empfehlungen für dieses Produkt

Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.

Alle anzeigen 1

	Typ	Titel		Datum
*	Data sheet	LDC5071-Q1Inductive Position Sensor Front-End With Sin/Cos Interface datasheet	PDF \| HTML	06 Dez 2023

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Evaluierungsplatine

LDC5072Q1EVM — LDC5072–Q1 Evaluierungsmodul für induktive Positionssensorschnittstelle mit Sinus-/Kosinus-Ausgängen

Das Evaluierungsmodul (EVM) LDC5072-Q1 unterstützt Entwickler bei der Evaluierung des Betriebs und der Leistung des induktiven Positionssensors LDC5072-Q1. Das EVM enthält alle für den LDC5072-Q1 erforderlichen passiven Bauelemente und kann schnell in einem System evaluiert werden. Eine (...)

Benutzerhandbuch: PDF

Nicht verfügbar auf TI.com

Gehäuse	Pins	CAD-Symbole, Footprints und 3D-Modelle
TSSOP (PW)	16	Ultra Librarian

Es gelten die allgemeinen Geschäftsbedingungen von TI für Evaluierungsartikel.

LDC5071-Q1

Induktiver Positionssensor AFE mit Sinus/Cosinus-Schnittstelle für die Automobilindustrie

LDC5071-Q1

Produktdetails

Technische Dokumentation

Design und Entwicklung

LDC5072Q1EVM — LDC5072–Q1 Evaluierungsmodul für induktive Positionssensorschnittstelle mit Sinus-/Kosinus-Ausgängen

Bestellen & Qualität

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Videoreihe

Videos