제품 상세 정보

Vs (max) (V) 8 Vs (min) (V) 1.4 Operating temperature range (°C) -55 to 125 Rating Catalog
Vs (max) (V) 8 Vs (min) (V) 1.4 Operating temperature range (°C) -55 to 125 Rating Catalog
PDIP (P) 8 92.5083 mm² 9.81 x 9.43
  • Low Voltage Supply (3V–5.5V)
  • 22 mA Output Drive Current
  • No RFI Radiation
  • Adaptable to All Injector Current Levels
  • Highly Accurate Operation
  • TTL/CMOS Compatible Input Logic Levels
  • Short Circuit Protection
  • High Impedance Input
  • Externally Set Holding Current, IH
  • Internally Set Peak Current (4 × IH)
  • Externally Set Time-Out
  • Can be Modified for Full Switching Operation
  • Available in Plastic 8-Pin PDIP

All trademarks are the property of their respective owners.

  • Low Voltage Supply (3V–5.5V)
  • 22 mA Output Drive Current
  • No RFI Radiation
  • Adaptable to All Injector Current Levels
  • Highly Accurate Operation
  • TTL/CMOS Compatible Input Logic Levels
  • Short Circuit Protection
  • High Impedance Input
  • Externally Set Holding Current, IH
  • Internally Set Peak Current (4 × IH)
  • Externally Set Time-Out
  • Can be Modified for Full Switching Operation
  • Available in Plastic 8-Pin PDIP

All trademarks are the property of their respective owners.

The LM1949 linear integrated circuit serves as an excellent control of fuel injector drive circuitry in modern automotive systems. The IC is designed to control an external power NPN Darlington transistor that drives the high current injector solenoid. The current required to open a solenoid is several times greater than the current necessary to merely hold it open; therefore, the LM1949, by directly sensing the actual solenoid current, initially saturates the driver until the “peak” injector current is four times that of the idle or “holding” current (–). This guarantees opening of the injector. The current is then automatically reduced to the sufficient holding level for the duration of the input pulse. In this way, the total power consumed by the system is dramatically reduced. Also, a higher degree of correlation of fuel to the input voltage pulse (or duty cycle) is achieved, since opening and closing delays of the solenoid will be reduced.

Normally powered from a 5V ± 10% supply, the IC is typically operable over the entire temperature range (−55°C to +125°C ambient) with supplies as low as 3 volts. This is particularly useful under “cold crank” conditions when the battery voltage may drop low enough to deregulate the 5-volt power supply.

The LM1949 is available in the plastic PDIP, (contact factory for other package options).

The LM1949 linear integrated circuit serves as an excellent control of fuel injector drive circuitry in modern automotive systems. The IC is designed to control an external power NPN Darlington transistor that drives the high current injector solenoid. The current required to open a solenoid is several times greater than the current necessary to merely hold it open; therefore, the LM1949, by directly sensing the actual solenoid current, initially saturates the driver until the “peak” injector current is four times that of the idle or “holding” current (–). This guarantees opening of the injector. The current is then automatically reduced to the sufficient holding level for the duration of the input pulse. In this way, the total power consumed by the system is dramatically reduced. Also, a higher degree of correlation of fuel to the input voltage pulse (or duty cycle) is achieved, since opening and closing delays of the solenoid will be reduced.

Normally powered from a 5V ± 10% supply, the IC is typically operable over the entire temperature range (−55°C to +125°C ambient) with supplies as low as 3 volts. This is particularly useful under “cold crank” conditions when the battery voltage may drop low enough to deregulate the 5-volt power supply.

The LM1949 is available in the plastic PDIP, (contact factory for other package options).

다운로드 스크립트와 함께 비디오 보기 동영상

기술 자료

star =TI에서 선정한 이 제품의 인기 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하십시오.
2개 모두 보기
유형 직함 날짜
* Data sheet LM1949 Injector Drive Controller datasheet (Rev. C) 2013/03/20
More literature Die D/S LM1949 MDC Injector Drive Controller 2012/09/19

설계 및 개발

추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.

패키지 CAD 기호, 풋프린트 및 3D 모델
PDIP (P) 8 Ultra Librarian

주문 및 품질

포함된 정보:
  • RoHS
  • REACH
  • 디바이스 마킹
  • 납 마감/볼 재질
  • MSL 등급/피크 리플로우
  • MTBF/FIT 예측
  • 물질 성분
  • 인증 요약
  • 지속적인 신뢰성 모니터링
포함된 정보:
  • 팹 위치
  • 조립 위치

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

콘텐츠는 TI 및 커뮤니티 기고자에 의해 "있는 그대로" 제공되며 TI의 사양으로 간주되지 않습니다. 사용 약관을 참조하십시오.

품질, 패키징, TI에서 주문하는 데 대한 질문이 있다면 TI 지원을 방문하세요. ​​​​​​​​​​​​​​

동영상