首頁 音訊 音訊放大器 喇叭放大器
首頁
音訊
音訊放大器
喇叭放大器

TAS6584-Q1

現行

具電流感測功能的車用 45-V、10-A 數位輸入、四通道 D 類音訊放大器

立即訂購
產品規格表

現在提供此產品的更新版本

open-in-new 比較替代產品
可直接投入的替代產品，相較於所比較的裝置，具備升級功能
最新 TAS6684-Q1 現行 具電流感測功能的車用、45V、13A、數位輸入、四通道 D 類音訊放大器 13A/ch version

TAS6584-Q1

現行
產品規格表 立即訂購

產品詳細資料

Audio input type Digital Input Architecture Class-D Speaker channels (max) 4 Rating Automotive Power stage supply (max) (V) 45 Power stage supply (min) (V) 4.5 Load (min) (Ω) 2 Output power (W) 215 SNR (dB) 111 THD + N at 1 kHz (%) 0.03 Iq (typ) (mA) 120 Control interface I2C Closed/open loop Closed Analog supply (min) (V) 4.5 Analog supply voltage (max) (V) 45 Sampling rate (max) (kHz) 192 PSRR (dB) 75 Operating temperature range (°C) -40 to 125
Audio input type Digital Input Architecture Class-D Speaker channels (max) 4 Rating Automotive Power stage supply (max) (V) 45 Power stage supply (min) (V) 4.5 Load (min) (Ω) 2 Output power (W) 215 SNR (dB) 111 THD + N at 1 kHz (%) 0.03 Iq (typ) (mA) 120 Control interface I2C Closed/open loop Closed Analog supply (min) (V) 4.5 Analog supply voltage (max) (V) 45 Sampling rate (max) (kHz) 192 PSRR (dB) 75 Operating temperature range (°C) -40 to 125
HTQFP (PHD) 64 256 mm² 16 x 16
  • AEC-Q100 qualified for automotive applications
    • Temperature grade 1: –40°C to +125°C, TA
  • General operation
    • 4.5-V to 45-V supply voltage, 50-V load dump
    • Support for 1.8-V and 3.3-V I/O’s
    • I2C control with 8 address options
    • <2-W idle power loss at 14.4 V, <8-uA max VBAT+PVDD shutdown loss
  • Integrated DSP processing
    • Class-H supply voltage control
    • Thermal monitoring and foldback
    • Clip detection, PVDD monitoring and foldback
  • Output current sensing by channel via I2S/TDM
    • No need for external circuitry
  • Real-time load diagnostics
    • Monitor output conditions while playing audio
    • Open load, Shorted load, Short-to-power, Short-to-ground detection
  • DC and AC Standby load diagnostics
  • Audio inputs
    • 2-4 channel I2S or 4-16 channel TDM input
    • Input sample rates: 44.1, 48, 96, 192 kHz
    • Secondary low latency path, >70% reduced signal delay at 48 kHz
  • Audio outputs
    • 4-channel bridge-tied load (BTL), configurable 2-channel parallel BTL (PBTL)
    • 384-kHz to 2.1-MHz configurable output switching frequency
    • Up to 10-A channel output current
    • 400-VA peak BTL output power
    • 118 W (45 V, 8 Ω, 1% THD, BTL)
    • 215 W (45 V, 4 Ω, 1% THD, BTL)
  • Audio Performance
    • THD+N 0.03% (8 Ω, 1 W, 1 kHz)
    • 111 dB SNR
    • 37 µV (14.4 V), 80 µV (45 V) output noise
  • Protection
    • Output short protection
    • DC offset, undervoltage and overvoltage
    • Configurable overtemperature warning and individual channel shutdown
    • I2C temperature and supply voltage readout
  • Easily meet CISPR25-L5 EMC specification
    • Advanced spread-spectrum
  • AEC-Q100 qualified for automotive applications
    • Temperature grade 1: –40°C to +125°C, TA
  • General operation
    • 4.5-V to 45-V supply voltage, 50-V load dump
    • Support for 1.8-V and 3.3-V I/O’s
    • I2C control with 8 address options
    • <2-W idle power loss at 14.4 V, <8-uA max VBAT+PVDD shutdown loss
  • Integrated DSP processing
    • Class-H supply voltage control
    • Thermal monitoring and foldback
    • Clip detection, PVDD monitoring and foldback
  • Output current sensing by channel via I2S/TDM
    • No need for external circuitry
  • Real-time load diagnostics
    • Monitor output conditions while playing audio
    • Open load, Shorted load, Short-to-power, Short-to-ground detection
  • DC and AC Standby load diagnostics
  • Audio inputs
    • 2-4 channel I2S or 4-16 channel TDM input
    • Input sample rates: 44.1, 48, 96, 192 kHz
    • Secondary low latency path, >70% reduced signal delay at 48 kHz
  • Audio outputs
    • 4-channel bridge-tied load (BTL), configurable 2-channel parallel BTL (PBTL)
    • 384-kHz to 2.1-MHz configurable output switching frequency
    • Up to 10-A channel output current
    • 400-VA peak BTL output power
    • 118 W (45 V, 8 Ω, 1% THD, BTL)
    • 215 W (45 V, 4 Ω, 1% THD, BTL)
  • Audio Performance
    • THD+N 0.03% (8 Ω, 1 W, 1 kHz)
    • 111 dB SNR
    • 37 µV (14.4 V), 80 µV (45 V) output noise
  • Protection
    • Output short protection
    • DC offset, undervoltage and overvoltage
    • Configurable overtemperature warning and individual channel shutdown
    • I2C temperature and supply voltage readout
  • Easily meet CISPR25-L5 EMC specification
    • Advanced spread-spectrum

The TAS6584-Q1 is a four-channel, digital-input, high-voltage, Class-D audio amplifier that supports up to 45-V supply voltage. In combination with up to 10-A output current, this device delivers maximum output power and high fidelity audio in high and low impedance loads. The device provides four channels at 118 W (45 V, 8 Ω, 1% THD, BTL) and 215 W (45 V, 4 Ω, 1% THD, BTL).

The TAS6584-Q1 integrates DC and AC load diagnostics to determine the status of the connected loads before enabling the output stage. During audio playback, the status can be monitored through output current sense which is available for each channel and reports the measurement to a host processor through TDM with minimal delay. The device monitors the output load condition while playing audio using real-time load diagnostics which operate independent from host and audio input.

To optimize system efficiency, the integrated DSP of the TAS6584-Q1 enables Class-H envelope tracking control, eliminating the need for development of complex tracking software and making local boost voltage control possible without the need for an external microcontroller.

The TAS6584-Q1 device features an additional low-latency signal path for each channel, providing up to 70% faster signal processing at 48 kHz which enables time-sensitive Active Noise Cancellation (ANC), Road Noise Cancellation (RNC) applications.

The device is offered in a 64-pin QFP package with the exposed thermal pad up.

The TAS6584-Q1 is a four-channel, digital-input, high-voltage, Class-D audio amplifier that supports up to 45-V supply voltage. In combination with up to 10-A output current, this device delivers maximum output power and high fidelity audio in high and low impedance loads. The device provides four channels at 118 W (45 V, 8 Ω, 1% THD, BTL) and 215 W (45 V, 4 Ω, 1% THD, BTL).

The TAS6584-Q1 integrates DC and AC load diagnostics to determine the status of the connected loads before enabling the output stage. During audio playback, the status can be monitored through output current sense which is available for each channel and reports the measurement to a host processor through TDM with minimal delay. The device monitors the output load condition while playing audio using real-time load diagnostics which operate independent from host and audio input.

To optimize system efficiency, the integrated DSP of the TAS6584-Q1 enables Class-H envelope tracking control, eliminating the need for development of complex tracking software and making local boost voltage control possible without the need for an external microcontroller.

The TAS6584-Q1 device features an additional low-latency signal path for each channel, providing up to 70% faster signal processing at 48 kHz which enables time-sensitive Active Noise Cancellation (ANC), Road Noise Cancellation (RNC) applications.

The device is offered in a 64-pin QFP package with the exposed thermal pad up.
filter 尋找其它 喇叭放大器
下載 觀看有字幕稿的影片 影片
索取更多資訊

提供完整產品規格表、PurePath™ Console 3、TAS6584-Q1 GUI和其他設計資源。立即索取

您可能會感興趣的類似產品

open-in-new 比較替代產品
引腳對引腳且具備與所比較裝置相同的功能
TAS6582-Q1 預覽 具電流感測的車用、45-V、10-A 數位輸入雙通道 D 類音訊放大器 TAS6582-Q1 is the 2 channel version of the 4 channel TAS6584-Q1

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 7
類型 標題 日期
* Data sheet TAS6584-Q1 - 45-V​​​, 10-A Digital Input 4-Channel Automotive Class-D Audio Amplifier with Current Sense and Real-time Load Diagnostics datasheet (Rev. A) PDF | HTML 2022年 3月 28日
Application note TAS6x84-Q1 LC Filter Selection Guide PDF | HTML 2024年 10月 15日
Application brief TAS6584-Q1 in Personal Electronics PDF | HTML 2022年 11月 23日
Application brief 實時負載診斷 PDF | HTML 2022年 3月 7日
Product overview 車用 D 類音訊放大器 PDF | HTML 2022年 3月 7日
Technical article Creating an immersive automotive audio experience with higher output power and Cla PDF | HTML 2022年 2月 22日
Application note Inductor Selection Guide for 2.1 MHz Class-D Amplifiers (Rev. A) 2019年 9月 5日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TAS6584Q1EVM — 適用於 45V、10A 數位輸入、四通道 D 類音訊放大器的 TAS6584-Q1 評估模組

TAS6584Q1EVM 評估模組 (EVM)，展示具有電流感測和即時負載診斷功能的 TAS6584-Q1、45V、10A 數位輸入四通道車用、D 類音訊放大器。EVM 也配備適用於 GUI 驅動 EVM 評估的板載 USB-I²C 控制器。TAS6584-Q1 車用 D 類放大器，可幫助打造身臨其境的音訊體驗，同時在音訊播放期間支援即時喇叭診斷。TAS6584-Q1 可為每通道提供 213W (1% THD+N)，在 45V 電源時為 4Ω。TAS6584-Q1 裝置擁有從 4.5V 到 45V 的廣泛供應電壓功能，並整合 DC 與 AC (...)

要求
支援軟體

TAS6584-Q1-DESIGN — TAS6584-Q1 documents

TAS6584-Q1 full datasheet and related design documents.
支援產品和硬體

支援產品和硬體

產品
喇叭放大器
TAS6584-Q1 — 具電流感測功能的車用 45-V、10-A 數位輸入、四通道 D 類音訊放大器
硬體開發
開發板
TAS6584Q1EVM — 適用於 45V、10A 數位輸入、四通道 D 類音訊放大器的 TAS6584-Q1 評估模組
要求
支援軟體

TAS6584-SW — TAS6584-Q1 EVM software

TAS6584-Q1 EVM software
支援產品和硬體

支援產品和硬體

產品
喇叭放大器
TAS6584-Q1 — 具電流感測功能的車用 45-V、10-A 數位輸入、四通道 D 類音訊放大器
硬體開發
開發板
TAS6584Q1EVM — 適用於 45V、10A 數位輸入、四通道 D 類音訊放大器的 TAS6584-Q1 評估模組
要求
設計工具

TIDA-020033-TD-DESIGN — TIDA-020033 test documentation

支援產品和硬體

支援產品和硬體

產品
AC/DC 和 DC/DC 控制器 (外部 FET)
LM5123-Q1 — 2.2MHz 大範圍 VIN 低 IQ 同步升壓控制器 LM51231-Q1 — 具有輸出電壓追蹤功能的 2.2-MHz 大範圍 VIN、同步升壓控制器
類比電流感測放大器
INA302-Q1 — 具雙比較器的 AEC-Q100、36V、雙向、550kHz、4V/µs、高精度電流感測放大器
喇叭放大器
TAS6584-Q1 — 具電流感測功能的車用 45-V、10-A 數位輸入、四通道 D 類音訊放大器
理想二極體/ORing 控制器
LM7481-Q1 — 具有主動式整流驅動 B2B NFET 的車用理想二極體控制器
要求
模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
要求
參考設計

TIDA-020033 — 車用 H 類音訊與追蹤電源供應器參考設計

此參考設計展示 H 類音訊與追蹤電源供應音訊子系統。TAS6584-Q1 音訊放大器可追蹤數位音訊輸入的包絡線，並調整 LM5123-Q1 升壓輸出電壓以符合電源效率需求，無需使用外部微控制器。此參考設計可提升效率、熱性能，且總體積更小。此外，此參考設計也允許 H 類實作隨插即用，對汽車音訊架構的其他部分只有最少的軟體更動。
Design guide: PDF
封裝 針腳 CAD 符號、佔位空間與 3D 模型
HTQFP (PHD) 64 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片