Soporte de software
BQ25150
Cargador de batería lineal de 500 mA controlado por I2C con ruta de alimentación, bajo Iq, LDO integ
Hoja de datos
BQ25150
- Linear battery charger with 1.25-mA to 500-mA fast charge current range
- 0.5% Accurate I 2C programmable battery regulation voltage ranging from 3.6 V to 4.6 V in 10-mV steps
- Configurable termination current supporting down to 0.5 mA
- 20-V Tolerant input with typical 3.4-V to 5.5-V input voltage operating range
- Programmable thermal charging profile, fully configurable hot, warm, cool and cold thresholds
- Power path management for powering system and charging battery
- Dynamic power path management optimizes charging from weak adapters
- Advanced I 2C control allows host to disconnect the battery or adapter as needed
- I 2C Configurable load switch or up to 150-mA LDO output
- Programmable range from 0.6 V to 3.7 V in 100-mV steps
- Ultra low Iddq for extended battery life
- 10-nA Ship mode battery Iq
- 400-nA Iq While powering the system (PMID and VDD on)
- One push-button wake-up and reset input with adjustable timers
- Supports system power cycle and HW reset
- 16-Bit ADC
- Monitoring of charge current, battery thermistor and battery, input and system (PMID) voltages
- General purpose ADC input
- Always on 1.8-V VDD LDO supporting loads up to 10 mA
- 20-Pin 2-mm x 1.6-mm CSP package
- 12-mm 2 Total solution size
The BQ25150 is a highly integrated battery charge management IC that integrates the most common functions for wearable devices, namely a charger, an output voltage rail, ADC for battery and system monitoring, and push-button controller.
The BQ25150 IC integrates a linear charger that enables quick and accurate charging for small batteries. The device supports charge current up to 500 mA and supports termination current down to 0.5 mA for maximum charge. The battery is charged using a standard Li-Ion charge profile with three phases: pre-charge, constant current and constant voltage regulation.
The device integrates advanced power path management and control that allows the device to provide power to the system while charging the battery even with poor adapters. The host may also control the power path through I 2C allowing it to disconnect the input adapter and/or battery without physically removing them. The single push-button input eliminates the need of a separate button controller IC reducing the total solution footprint. The push-button input can be used for wake functions or to reset the system. A 12-bit effective ADC enables accurate battery voltage monitoring and can be used to enable a low Iq gauging to monitor battery health. It can also be used to measure the battery temperature using a thermistor connected to the TS pin as well as external system signals through the ADCIN pin. The low quiescent current during operation and shutdown enables maximum battery life. The input current limit, charge current, LDO output voltage, and other parameters are programmable through the I 2C interface making the BQ25150 a very flexible charging solution. A voltage-based JEITA compatible (or standard HOT/COLD) battery pack thermistor monitoring input (TS) is included that monitors battery temperature and automatically changes charge parameters to prevent the battery from charging outside of its safe temperature range. The temperature thresholds are also programable through I 2C allowing the host to customize the thermal charging profile. The charger is optimized for 5-V USB input, with 20-V absolute maximum tolerance to withstand line transients. The device also integrates a linear regulator to provide a quiet rail for radios or processors and can be independently sourced and controlled through I 2C.
Productos similares que pueden interesarle
Pin por pin con la misma funcionalidad que el dispositivo comparado
Documentación técnica
No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 9 | Tipo | Título | Fecha | ||
|---|---|---|---|---|
| * | Data sheet | BQ25150 I2C Controlled 1-Cell 500-mA Linear Charger with 10-nA Ship Mode, Advanced Power Path Management and Control, ADC, and LDO datasheet (Rev. C) | PDF | HTML | 26 abr 2023 |
| Application note | Implementing 2-V Charge Inhibition | PDF | HTML | 31 may 2023 | |
| Application note | High-Efficiency Charging for TWS Using a 2-Pin Interface Application Report (Rev. A) | PDF | HTML | 16 may 2023 | |
| Application note | State of Charge Estimation Using Smart Battery Charger | PDF | HTML | 11 oct 2021 | |
| Application note | Battery Discharge Implementation in Warm or Hot Temperatures | 02 jul 2019 | ||
| Application note | BQ2515x Setup Guide | 18 jun 2019 | ||
| EVM User's guide | BQ2515xEVM User's Guide (Rev. A) | 13 jun 2019 | ||
| Technical article | Pull the tab: How to implement ship mode in your lithium-ion battery design | PDF | HTML | 20 feb 2019 | |
| User guide | Small Form Factor Design for BQ25150 | 24 jul 2018 |
Diseño y desarrollo
Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.
Placa de evaluación
BQ25150EVM — Solución avanzada de gestión de carga y ruta de alimentación de bajo IQ para módulo de evaluación de
The bq25150EVM evaluation module is an integrated battery charge management IC that integrates the most common functions for wearables devices: Linear charger, regulated output, load switch, manual reset with timer, ADC, ship mode and advanced power path. The low quiescent current during operation (...)
Guía del usuario: PDF
Adaptador de interfaz
EV2400 — Módulo de evaluación de placa de interfaz de PC basada en USB para indicador de combustible (gas) de
The EV2400 EVM interface board enables an IBM-compatible or other type PC (with the required driver for its particular platform) to communicate with the Texas Instruments SMBus or I2C interface gas gauges via a Universal Serial Bus (USB) port. In addition to this board, PC software is required to (...)
Guía del usuario: PDF
Software de aplicación y estructura
BQSTUDIO — Software Battery Management Studio (bqStudio)
Battery Management Studio (bqStudio) ofrece un conjunto completo de herramientas robustas para ayudar con el proceso de evaluación, diseño, configuración, prueba o utilización de productos de gestión de baterías de TI. Esto incluye funciones que (...)
Controlador o biblioteca
BQ2515XSW-LINUX — Controlador Linux para BQ2515X
The Linux driver supports the BQ25155 I2C controlled, 1-cell, 500-mA linear charger. The Linux driver supports communication through the I2C bus and interfaces with the power supply sub-system.
Available through git.ti.com: no
Linux Mainline Status
Available in Linux Main line: YesAvailable through git.ti.com: no
Supported (...)
Diseños de referencia
PMP21884 — Diseño de referencia de fuente de alimentación CC-CC diminuta y de muy baja IQ con carga de batería
This is a highly-integrated power supply reference design for smartwatches and fitness trackers enabling ultra-low IQ that is ultra-small (48 sq mm). Supply includes seven power rails including battery charger, LDO, DC/DC buck converters and integrated boost converter for heart rate monitor, AFE (...)
| Encapsulado | Pines | Símbolos CAD, huellas y modelos 3D |
|---|---|---|
| DSBGA (YFP) | 20 | Ultra Librarian |
Pedidos y calidad
Información incluida:
- RoHS
- REACH
- Marcado del dispositivo
- Acabado de plomo/material de la bola
- Clasificación de nivel de sensibilidad a la humedad (MSL) / reflujo máximo
- Estimaciones de tiempo medio entre fallas (MTBF)/fallas en el tiempo (FIT)
- Contenido del material
- Resumen de calificaciones
- Monitoreo continuo de confiabilidad
Información incluida:
- Lugar de fabricación
- Lugar de ensamblaje
Los productos recomendados pueden tener parámetros, módulos de evaluación o diseños de referencia relacionados con este producto de TI.
Soporte y capacitación
Foros de TI E2E™ con asistencia técnica de los ingenieros de TI
El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.
Si tiene preguntas sobre la calidad, el paquete o el pedido de productos de TI, consulte el soporte de TI.