Ejemplo de código o demostración
TPA3255
Amplificador de audio estéreo de 315 W y mono de 600 W, Clase D, entrada analógica y alimentación de
Hoja de datos
TPA3255
- Differential Analog Inputs
- Total Output Power at 10%THD+N
- 315-W Stereo into 4 Ω in BTL Configuration
- 185-W Stereo into 8 Ω in BTL Configuration
- 600-W Mono into 2 Ω in PBTL Configuration
- Total Output Power at 1%THD+N
- 260-W Stereo into 4 Ω in BTL Configuration
- 150-W Stereo into 8 Ω in BTL Configuration
- 480-W Mono into 2 Ω in PBTL Configuration
- Advanced Integrated Feedback Design with High-speed Gate Driver Error Correction
(PurePath™ Ultra-HD)- Signal Bandwidth up to 100 kHz for High Frequency Content From HD Sources
- Ultra Low 0.006% THD+N at 1 W into 4 Ω and <0.01% THD+N to Clipping
- >65 dB PSRR (BTL, 1 kHz, No Input Signal)
- <85 µV (A-Weighted) Output Noise
- >111 dB (A Weighted) SNR
- Multiple Configurations Possible:
- Stereo, Mono, 2.1 and 4xSE
- Click and Pop Free Startup and Stop
- 90% Efficient Class-D Operation (4 Ω)
- Wide 18-V to 53.5V Supply Voltage Operation
- Self-Protection Design (Including Undervoltage, Overtemperature, Clipping, and Short Circuit Protection) With Error Reporting
- EMI Compliant When Used With Recommended System Design
TPA3255 is a high performance class-D power amplifier that enables true premium sound quality with class-D efficiency. It features an advanced integrated feedback design and proprietary high-speed gate driver error correction (PurePath™ Ultra-HD). This technology allows ultra low distortion across the audio band and superior audio quality. The device is operated in AD-mode, and can drive up to 2 x 315 W into 4-Ω load at 10% THD and 2 x 150 W unclipped into 8-Ω load and features a 2 VRMS analog input interface that works seamlessly with high performance DACs such as TI’s PCM5242. In addition to excellent audio performance, TPA3255 achieves both high power efficiency and very low power stage idle losses below 2.5W. This is achieved through the use of 85 mΩ MOSFETs and an optimized gate driver scheme that achieves significantly lower idle losses than typical discrete implementations.
Documentación técnica
No se encontraron resultados. Borre su búsqueda y vuelva a intentarlo.
Ver todo 14 Diseño y desarrollo
Para conocer los términos adicionales o los recursos necesarios, haga clic en cualquier título de abajo para ver la página de detalles cuando esté disponible.
Placa de evaluación
SIDEGIG-GUITAREVM — Módulo complementario Guitar SideGig
The TI Guitar SideGig plug-in module turns TI Audio Class-D amplifier EVM’s into a guitar, bass or musical instrument amplifier. The board features selectable “clean” and “drive” channels for traditional and overdriven guitar sounds. The clean channel offers volume, (...)
Guía del usuario: PDF
Placa de evaluación
SIDEGIG-PROTOEVM — Módulo complementario de audio prototipo
The TI Prototype Audio Plug-in Module turns TI Audio Class-D amplifier EVM’s into your sandbox. Need to prototype a pre-amplifier circuit or test an opamp with TI Class-D EVMs, then start with the DIY Audio Plug-in Module.
Start your prototype on the included breadboard or solder directly to the (...)
Start your prototype on the included breadboard or solder directly to the (...)
Guía del usuario: PDF
Placa de evaluación
SIDEGIG-XOVEREVM — Módulo complementario de audio cruzado activo analógico
The TI Analog, Active Crossover Audio Plug-in Module turns TI Audio Class-D amplifier EVM’s into a high quality, two-way speaker amplifier. The plug-in module makes it easy to remove the large and expensive passive crossover found in passive loudspeakers and create a biamped, two-way (...)
Guía del usuario: PDF
Herramienta de cálculo
LCFILTER-CALC-TOOL — Class-D LC Filter Designer
Calculate and design audio Class-D LC filters in minutes using the Class-D LC Filter Designer. Select from 4 different filter types based on Class-D output, switching topology and performance. Input corner frequency and quality (Q) factor to fine tune the audio frequency (...)
Productos y hardware compatibles
Productos
Amplificadores para altavoces
Desarrollo de hardware
Placa de evaluación
Software
Herramienta de diseño
Herramienta de simulación
PSPICE-FOR-TI — PSpice® para herramienta de diseño y simulación de TI
PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Diseños de referencia
PMP10215 — Diseño de referencia de entrada universal a 3,3 V, 12 V, 36 V, 200 W de potencia continua para ampli
This power module generates all voltages to supply a class-D audio amplifier. The main output voltage is 36V and delivers 200W continuously and 840W peak. The first stage is a power-factor corrected Boost. A Flyback converter supplies 12V on primary side as well as 12V@300mA and 3.3V@200mA on (...)
| Encapsulado | Pines | Símbolos CAD, huellas y modelos 3D |
|---|---|---|
| HTSSOP (DDV) | 44 | Ultra Librarian |
Pedidos y calidad
Información incluida:
- RoHS
- REACH
- Marcado del dispositivo
- Acabado de plomo/material de la bola
- Clasificación de nivel de sensibilidad a la humedad (MSL) / reflujo máximo
- Estimaciones de tiempo medio entre fallas (MTBF)/fallas en el tiempo (FIT)
- Contenido del material
- Resumen de calificaciones
- Monitoreo continuo de confiabilidad
Información incluida:
- Lugar de fabricación
- Lugar de ensamblaje
Los productos recomendados pueden tener parámetros, módulos de evaluación o diseños de referencia relacionados con este producto de TI.
Soporte y capacitación
Foros de TI E2E™ con asistencia técnica de los ingenieros de TI
El contenido lo proporcionan “tal como está” TI y los colaboradores de la comunidad y no constituye especificaciones de TI. Consulte los términos de uso.
Si tiene preguntas sobre la calidad, el paquete o el pedido de productos de TI, consulte el soporte de TI.