LM3914

最終購入段階

ドットまたはバーのディスプレイ・ドライバ

ご注文はこちら

データシート

document-pdfAcrobat LM3914 Dot/Bar Display Driver データシート (Rev. B) (英語)

LM3914 は生産中止予定です

この製品は、生産中止予定です。新規設計では代替品をご検討ください。

open-in-new

代替品と比較

比較対象デバイスと類似の機能

LP3944

アクティブ

RGB / 白 / 青の LED を 8 つ駆動する楽しい照明ドライバ This product is an LED controller for RGB/color/white LEDs with an I2C interface.

LP5012

アクティブ

12 チャネル、I2C、定電流 RGB LED ドライバ Newer device with more outputs, larger current and smaller Iq

LM3914

最終購入段階

データシート

ご注文はこちら

製品詳細

Number of channels

10

LED current per channel (mA)

10

Vin (min) (V)

3

Vin (max) (V)

15

Shutdown current (ISD) (typ) (µA)

2.4

Operating temperature range (°C)

0 to 70

Rating

Catalog

Number of channels

10

LED current per channel (mA)

10

Vin (min) (V)

3

Vin (max) (V)

15

Shutdown current (ISD) (typ) (µA)

2.4

Operating temperature range (°C)

0 to 70

Rating

Catalog

PLCC (FN)

20

98.01 mm² 9.9 x 9.9

Drives LEDs, LCDs or Vacuum Fluorescents
Bar or Dot Display Mode Externally Selectable by User
Expandable to Displays of 100 Steps
Internal Voltage Reference from 1.2V to 12V
Operates with Single Supply of Less than 3V
Inputs Operate Down to Ground
Output Current Programmable from 2 mA to 30 mA
No Multiplex Switching or Interaction Between Outputs
Input Withstands ±35V without Damage or False Outputs
LED Driver Outputs are Current Regulated, Open-collectors
Outputs can Interface with TTL or CMOS Logic
The Internal 10-step Divider is Floating and can be Referenced to a Wide Range of Voltages

All trademarks are the property of their respective owners.

Drives LEDs, LCDs or Vacuum Fluorescents
Bar or Dot Display Mode Externally Selectable by User
Expandable to Displays of 100 Steps
Internal Voltage Reference from 1.2V to 12V
Operates with Single Supply of Less than 3V
Inputs Operate Down to Ground
Output Current Programmable from 2 mA to 30 mA
No Multiplex Switching or Interaction Between Outputs
Input Withstands ±35V without Damage or False Outputs
LED Driver Outputs are Current Regulated, Open-collectors
Outputs can Interface with TTL or CMOS Logic
The Internal 10-step Divider is Floating and can be Referenced to a Wide Range of Voltages

All trademarks are the property of their respective owners.

The LM3914 is a monolithic integrated circuit that senses analog voltage levels and drives 10 LEDs, providing a linear analog display. A single pin changes the display from a moving dot to a bar graph. Current drive to the LEDs is regulated and programmable, eliminating the need for resistors. This feature is one that allows operation of the whole system from less than 3V.

The circuit contains its own adjustable reference and accurate 10-step voltage divider. The low-bias-current input buffer accepts signals down to ground, or V⁻, yet needs no protection against inputs of 35V above or below ground. The buffer drives 10 individual comparators referenced to the precision divider. Indication non-linearity can thus be held typically to ½%, even over a wide temperature range.

Versatility was designed into the LM3914 so that controller, visual alarm, and expanded scale functions are easily added on to the display system. The circuit can drive LEDs of many colors, or low-current incandescent lamps. Many LM3914s can be “chained” to form displays of 20 to over 100 segments. Both ends of the voltage divider are externally available so that 2 drivers can be made into a zero-center meter.

The LM3914 is very easy to apply as an analog meter circuit. A 1.2V full-scale meter requires only 1 resistor and a single 3V to 15V supply in addition to the 10 display LEDs. If the 1 resistor is a pot, it becomes the LED brightness control. The simplified block diagram illustrates this extremely simple external circuitry.

When in the dot mode, there is a small amount of overlap or “fade” (about 1 mV) between segments. This assures that at no time will all LEDs be “OFF”, and thus any ambiguous display is avoided. Various novel displays are possible.

Much of the display flexibility derives from the fact that all outputs are individual, DC regulated currents. Various effects can be achieved by modulating these currents. The individual outputs can drive a transistor as well as a LED at the same time, so controller functions including “staging” control can be performed. The LM3914 can also act as a programmer, or sequencer.

The LM3914 is rated for operation from 0°C to +70°C. The LM3914N-1 is available in an 18-lead PDIP (NFK) package.

The following typical application illustrates adjusting of the reference to a desired value, and proper grounding for accurate operation, and avoiding oscillations.