BQ24153A

Name: BQ24153A
Brand: TI
SKU: BQ24153A
Price: 2.45 USD

활성

OTG 및 Vovp=6.5V를 지원하는 I2C 1셀 1.55A 벅 배터리 충전기

지금 주문

데이터 시트

document-pdfAcrobat bq2415x Fully Integrated Switch-Mode One-Cell Li-Ion Charger With Full USB Compliance and USB-OTG Support datasheet (Rev. D) (영어) PDF | HTML

BQ24153A

활성

데이터 시트

지금 주문

제품 상세 정보

Number of series cells

1

Charge current (max) (A)

1.25

Vin (max) (V)

6

Cell chemistry

Li-Ion/Li-Polymer

Battery charge voltage (min) (V)

3.5

Battery charge voltage (max) (V)

4.44

Absolute max Vin (max) (V)

20

Control topology

Switch-Mode Buck

Control interface

I2C

Features

BAT temp thermistor monitoring (hot/cold profile)

Vin (min) (V)

4

Rating

Catalog

Operating temperature range (°C)

-40 to 85

Number of series cells

1

Charge current (max) (A)

1.25

Vin (max) (V)

6

Cell chemistry

Li-Ion/Li-Polymer

Battery charge voltage (min) (V)

3.5

Battery charge voltage (max) (V)

4.44

Absolute max Vin (max) (V)

20

Control topology

Switch-Mode Buck

Control interface

I2C

Features

BAT temp thermistor monitoring (hot/cold profile)

Vin (min) (V)

4

Rating

Catalog

Operating temperature range (°C)

-40 to 85

DSBGA (YFF)

20

3.96 mm² 1.8 x 2.2

Charge Faster than Linear Chargers
High-Accuracy Voltage and Current Regulation
- Input Current Regulation Accuracy: ±5% (100
  mA and 500 mA)
- Charge Voltage Regulation Accuracy: ±0.5%
  (25°C), ±1% (0°C to 125°C)
- Charge Current Regulation Accuracy: ±5%
Input Voltage Based Dynamic Power
Management (VIN DPM)
Bad Adaptor Detection and Rejection
Safety Limit Register for Maximum Charge
Voltage and Current Limiting
High-Efficiency Mini-USB/AC Battery Charger for
Single-Cell Li-Ion and Li-Polymer Battery Packs
20-V Absolute Maximum Input Voltage Rating
9-V Maximum Operating Input Voltage-
bq24156A/9
6-V Maximum Operating Input Voltage-
bq24153A/8
Built-In Input Current Sensing and Limiting
Integrated Power FETs for Up To 1.55-A Charge
Rate
Programmable Charge Parameters through I²C
Compatible Interface (up to 3.4 Mbps):
- Input Current Limit
- VIN DPM Threshold
- Fast-Charge/Termination Current
- Charge Regulation Voltage (3.5 V to 4.44 V)
- Low Charge Current Mode Enable/Disable
- Safety Timer with Reset Control
- Termination Enable/Disable
Support up to 1.55 A Charge Current Using 55-
mΩ Sensing Resistor
Synchronous Fixed-Frequency PWM Controller
Operating at 3 MHz With 0% to 99.5% Duty Cycle
Automatic High Impedance Mode for Low Power
Consumption
Robust Protection
- Reverse Leakage Protection Prevents Battery
  Drainage
- Thermal Regulation and Protection
- Input/Output Overvoltage Protection
Status Output for Charging and Faults
USB Friendly Boot-Up Sequence
Automatic Charging
Power Up System without Battery bq24158/9
Boost Mode Operation for USB OTG:
(bq24153A/8 only)
- Input Voltage Range (from Battery): 2.5 V to
  4.5 V
- Output for V_BUS: 5.05 V/ 200 mA
2.1 mm × 2 mm 20-Pin WCSP Package

APPLICATIONS

Mobile and Smart Phones
MP3 Players
Handheld Devices

Charge Faster than Linear Chargers
High-Accuracy Voltage and Current Regulation
- Input Current Regulation Accuracy: ±5% (100
  mA and 500 mA)
- Charge Voltage Regulation Accuracy: ±0.5%
  (25°C), ±1% (0°C to 125°C)
- Charge Current Regulation Accuracy: ±5%
Input Voltage Based Dynamic Power
Management (VIN DPM)
Bad Adaptor Detection and Rejection
Safety Limit Register for Maximum Charge
Voltage and Current Limiting
High-Efficiency Mini-USB/AC Battery Charger for
Single-Cell Li-Ion and Li-Polymer Battery Packs
20-V Absolute Maximum Input Voltage Rating
9-V Maximum Operating Input Voltage-
bq24156A/9
6-V Maximum Operating Input Voltage-
bq24153A/8
Built-In Input Current Sensing and Limiting
Integrated Power FETs for Up To 1.55-A Charge
Rate
Programmable Charge Parameters through I²C
Compatible Interface (up to 3.4 Mbps):
- Input Current Limit
- VIN DPM Threshold
- Fast-Charge/Termination Current
- Charge Regulation Voltage (3.5 V to 4.44 V)
- Low Charge Current Mode Enable/Disable
- Safety Timer with Reset Control
- Termination Enable/Disable
Support up to 1.55 A Charge Current Using 55-
mΩ Sensing Resistor
Synchronous Fixed-Frequency PWM Controller
Operating at 3 MHz With 0% to 99.5% Duty Cycle
Automatic High Impedance Mode for Low Power
Consumption
Robust Protection
- Reverse Leakage Protection Prevents Battery
  Drainage
- Thermal Regulation and Protection
- Input/Output Overvoltage Protection
Status Output for Charging and Faults
USB Friendly Boot-Up Sequence
Automatic Charging
Power Up System without Battery bq24158/9
Boost Mode Operation for USB OTG:
(bq24153A/8 only)
- Input Voltage Range (from Battery): 2.5 V to
  4.5 V
- Output for V_BUS: 5.05 V/ 200 mA
2.1 mm × 2 mm 20-Pin WCSP Package

APPLICATIONS

Mobile and Smart Phones
MP3 Players
Handheld Devices

The bq24153A/6A/8/9 is a compact, flexible, high-efficiency, USB-friendly switch-mode charge management device for single-cell Li-ion and Li-polymer batteries used in a wide range of portable applications. The charge parameters can be programmed through an I²C interface. The IC integrates a synchronous PWM controller, power MOSFETs, input current sensing, high-accuracy current and voltage regulation, and charge termination, into a small WCSP package.

The IC charges the battery in three phases: conditioning, constant current and constant voltage. The input current is automatically limited to the value set by the host. Charge is terminated based on battery voltage and user-selectable minimum current level. A safety timer with reset control provides a safety backup for I²C interface. During normal operation, The IC automatically restarts the charge cycle if the battery voltage falls below an internal threshold and automatically enters sleep mode or high impedance mode when the input supply is removed. The charge status can be reported to the host using the I²C interface. During the charging process, the IC monitors its junction temperature (TJ) and reduces the charge current once TJ increases to about 125°C. To support USB OTG device, bq24153A/8 can provide VBUS (5.05 V) by boosting the battery voltage. The IC is available in 20-pin WCSP package.

The bq24153A/6A/8/9 is a compact, flexible, high-efficiency, USB-friendly switch-mode charge management device for single-cell Li-ion and Li-polymer batteries used in a wide range of portable applications. The charge parameters can be programmed through an I²C interface. The IC integrates a synchronous PWM controller, power MOSFETs, input current sensing, high-accuracy current and voltage regulation, and charge termination, into a small WCSP package.

The IC charges the battery in three phases: conditioning, constant current and constant voltage. The input current is automatically limited to the value set by the host. Charge is terminated based on battery voltage and user-selectable minimum current level. A safety timer with reset control provides a safety backup for I²C interface. During normal operation, The IC automatically restarts the charge cycle if the battery voltage falls below an internal threshold and automatically enters sleep mode or high impedance mode when the input supply is removed. The charge status can be reported to the host using the I²C interface. During the charging process, the IC monitors its junction temperature (TJ) and reduces the charge current once TJ increases to about 125°C. To support USB OTG device, bq24153A/8 can provide VBUS (5.05 V) by boosting the battery voltage. The IC is available in 20-pin WCSP package.

filter

기타 배터리 충전기 IC 찾기

다운로드 스크립트와 함께 비디오 보기 동영상

기술 자료

star

=TI에서 선정한 이 제품의 인기 문서

검색된 결과가 없습니다. 검색어를 지우고 다시 시도하십시오.

3개 모두 보기

	유형	직함		날짜
*	Data sheet	bq2415x Fully Integrated Switch-Mode One-Cell Li-Ion Charger With Full USB Compliance and USB-OTG Support datasheet (Rev. D)	PDF \| HTML	2014/01/28
	User guide	bq24153A/56A/57/58/59EVM Fully Integrated, Switch-Mode, One-Cell, Li-Ion Chgr (Rev. C)		2014/05/12
	Application note	Building your own Battery Simulator		2013/10/14

설계 및 개발

추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.

드라이버 또는 라이브러리

BQ2415XSW-LINUX — BQ2415X용 Linux 드라이버

Linux 드라이버는 완전 통합 스위치 모드 1셀 리튬-이온 충전기들로 구성된 BQ2415x 시리즈를 지원합니다. Linux 드라이버는 I2C 버스를 통한 통신을 지원하고 전원 공급 장치 서브 시스템과의 인터페이스를 제공합니다.

Linux 메인라인 상태

Linux 메인라인에서 사용 가능: 예
git.ti.com에서 구입 가능: 해당 없음

Linux 소스 파일

이 장치와 연계된 파일:

drivers/power/supply/bq2415x_charger.c
(...)

View Options

지원 소프트웨어

BQ24153A_6A_7B_8_9EVM_SW — BQ24153A_9 EVM v1.4.0.1

With either the bq24153AEVM-697, bq24156AEVM-697, bq24157BEVM, bq24158EVM-697 or BQ24159EVM-697 connected to a Windows PC via the USB-TO-GPIO box, this software provides a PC-based GUI interface so that you can communicate with the IC using the I2C communication protocol.

지원되는 제품 및 하드웨어

제품

배터리 충전기 IC

BQ24153A — OTG 및 Vovp=6.5V를 지원하는 I2C 1셀 1.55A 벅 배터리 충전기

BQ24156A — I2C 1셀 1.55A 벅 배터리 충전기

BQ24158 — OTG를 지원하며 전원을 켤 때 배터리가 없으면 감지하는 I2C 1셀 1.25A 벅 배터리 충전기

BQ24159 — USB와 완벽하게 호환되는 완전히 통합된 스위치 모드 싱글 셀 리튬 이온 충전기

하드웨어 개발

평가 보드

BQ24157EVM-697 — BQ24157EVM-697 평가 모듈

BQ24158EVM-697 — BQ24158 완전 통합 스위치 모드 1셀 리튬 이온 충전기용 평가 모듈

다운로드

패키지	핀	CAD 기호, 풋프린트 및 3D 모델
DSBGA (YFF)	20	Ultra Librarian

TI의 평가 항목에 대한 표준 약관이 적용됩니다.

BQ24153A

OTG 및 Vovp=6.5V를 지원하는 I2C 1셀 1.55A 벅 배터리 충전기

BQ24153A

제품 상세 정보

기술 자료

설계 및 개발

BQ2415XSW-LINUX — BQ2415X용 Linux 드라이버

BQ24153A_6A_7B_8_9EVM_SW — BQ24153A_9 EVM v1.4.0.1

지원되는 제품 및 하드웨어

제품

배터리 충전기 IC

하드웨어 개발

평가 보드

주문 및 품질

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

비디오 시리즈

동영상

옵션 다운로드

BQ24153A_6A_7B_8_9EVM_SW — BQ24153A_9 EVM v1.4.0.1

배터리 충전기 IC

하드웨어 개발

출시 정보