1.8GHz 전류 피드백 증폭기

THS3201은(는) 새 설계에 권장하지 않습니다
이 제품은 이전 설계를 지원하기 위해 계속 생산 중이지만 새로운 설계에 사용하는 것은 권장하지 않습니다. 다음 대안 중 하나를 고려하십시오.
open-in-new 대안 비교
비교 대상 장치와 유사한 기능
THS3491 활성 900MHz 고전력 출력 전류 피드백 증폭기 This current feedback amplifier (CFA) provides a new level of performance for applications requiring the lowest distortion at high output power levels from DC through values greater than 100 MHz at 100-Ω loads

제품 상세 정보

Architecture Current FB Number of channels 1 GBW (typ) (MHz) 1800 BW at Acl (MHz) 1800 Acl, min spec gain (V/V) 1 Slew rate (typ) (V/µs) 6700 Vn at flatband (typ) (nV√Hz) 1.65 Vn at 1 kHz (typ) (nV√Hz) 1.65 Iq per channel (typ) (mA) 14 Vos (offset voltage at 25°C) (max) (mV) 3 Rail-to-rail No Rating Catalog Operating temperature range (°C) -40 to 85 CMRR (typ) (dB) 71 Input bias current (max) (pA) 35000000 Offset drift (typ) (µV/°C) 10 Iout (typ) (mA) 115 2nd harmonic (dBc) 69 3rd harmonic (dBc) 75 Frequency of harmonic distortion measurement (MHz) 10
Architecture Current FB Number of channels 1 GBW (typ) (MHz) 1800 BW at Acl (MHz) 1800 Acl, min spec gain (V/V) 1 Slew rate (typ) (V/µs) 6700 Vn at flatband (typ) (nV√Hz) 1.65 Vn at 1 kHz (typ) (nV√Hz) 1.65 Iq per channel (typ) (mA) 14 Vos (offset voltage at 25°C) (max) (mV) 3 Rail-to-rail No Rating Catalog Operating temperature range (°C) -40 to 85 CMRR (typ) (dB) 71 Input bias current (max) (pA) 35000000 Offset drift (typ) (µV/°C) 10 Iout (typ) (mA) 115 2nd harmonic (dBc) 69 3rd harmonic (dBc) 75 Frequency of harmonic distortion measurement (MHz) 10
HVSSOP (DGN) 8 14.7 mm² 3 x 4.9 SOIC (D) 8 29.4 mm² 4.9 x 6 SOT-23 (DBV) 5 8.12 mm² 2.9 x 2.8
  • Unity-Gain Bandwidth: 1.8 GHz
  • High Slew Rate: 6700 V/µs (G = 2 V/V, RL = 100 , 10-V Step)
  • IMD3: -78 dBc at 20 MHz: (G = 10 V/V, RL = 100 , 2-VPP Envelope)
  • Noise Figure: 11 dB (G = 10 V/V, RG = 28 , RF = 255 )
  • Input-Referred Noise (f >10 MHz)
    • Voltage Noise: 1.65 nV/Hz
    • Noninverting Current Noise: 13.4 pA/Hz
    • Inverting Current Noise: 20 pA/Hz
  • Output Drive: 100 mA
  • Power-Supply Voltage Range: ±3.3 V to ±7.5 V
  • APPLICATIONS
    • Test and Measurement
    • ATE
    • High-Resolution, High-Sampling Rate ADC Drivers
    • High-Resolution, High-Sampling Rate DAC Output Buffers

PowerPAD is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.

  • Unity-Gain Bandwidth: 1.8 GHz
  • High Slew Rate: 6700 V/µs (G = 2 V/V, RL = 100 , 10-V Step)
  • IMD3: -78 dBc at 20 MHz: (G = 10 V/V, RL = 100 , 2-VPP Envelope)
  • Noise Figure: 11 dB (G = 10 V/V, RG = 28 , RF = 255 )
  • Input-Referred Noise (f >10 MHz)
    • Voltage Noise: 1.65 nV/Hz
    • Noninverting Current Noise: 13.4 pA/Hz
    • Inverting Current Noise: 20 pA/Hz
  • Output Drive: 100 mA
  • Power-Supply Voltage Range: ±3.3 V to ±7.5 V
  • APPLICATIONS
    • Test and Measurement
    • ATE
    • High-Resolution, High-Sampling Rate ADC Drivers
    • High-Resolution, High-Sampling Rate DAC Output Buffers

PowerPAD is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.

The THS3201 is a wideband, high-speed current-feedback amplifier, designed to operate over a wide supply range of ±3.3 V to ±7.5 V for today's high performance applications.

The wide supply range, combined with low distortion and high slew rate, makes the THS3201 ideally suited for arbitrary waveform driver applications. The distortion performance also enables driving high-resolution and high-sampling rate analog-to-digital converters (ADCs).

Its high voltage operation capabilities make the THS3201 especially suitable for many test, measurement, and ATE applications where lower voltage devices do not offer enough voltage swing capability. Output rise and fall times are nearly independent of step size (to first-order approximation), making the THS3201 ideal for buffering small to large step pulses with excellent linearity in high dynamic systems.

The THS3201 is offered in a 5-pin SOT-23, 8-pin SOIC, and an 8-pin MSOP with PowerPAD™ packages.

The THS3201 is a wideband, high-speed current-feedback amplifier, designed to operate over a wide supply range of ±3.3 V to ±7.5 V for today's high performance applications.

The wide supply range, combined with low distortion and high slew rate, makes the THS3201 ideally suited for arbitrary waveform driver applications. The distortion performance also enables driving high-resolution and high-sampling rate analog-to-digital converters (ADCs).

Its high voltage operation capabilities make the THS3201 especially suitable for many test, measurement, and ATE applications where lower voltage devices do not offer enough voltage swing capability. Output rise and fall times are nearly independent of step size (to first-order approximation), making the THS3201 ideal for buffering small to large step pulses with excellent linearity in high dynamic systems.

The THS3201 is offered in a 5-pin SOT-23, 8-pin SOIC, and an 8-pin MSOP with PowerPAD™ packages.

다운로드 스크립트와 함께 비디오 보기 동영상

기술 자료

star =TI에서 선정한 이 제품의 인기 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하십시오.
5개 모두 보기
유형 직함 날짜
* Data sheet THS3201: 1.8-GHz, Low Distortion, Current-Feedback Amplifiers datasheet (Rev. C) 2009/05/29
Application note Load Sharing Concepts: Implementation for Large-Signal Applications 2011/10/05
Application note Large-Signal Specifications for High-Voltage Line Drivers 2011/06/30
Application note Video Designs Using High-Speed Amplifiers (Rev. A) 2005/02/03
Application note Noise Analysis for High Speed Op Amps (Rev. A) 2005/01/17

설계 및 개발

추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.

평가 보드

THS3201EVM — THS3201 평가 모듈

The THS3201EVM provides a platform for evaluating the THS3201 high-speed current-feedback amplifier. The user needs only power, input signal, and test instruments to operate the EVM. The gain can be changed by changing the feedback and gain resistors. For a list of recommended resistor values, see (...)

TI.com에서 구매 불가
시뮬레이션 모델

THS3201 ADS Model

SLOJ176.ZIP (12 KB) - Spice Model
시뮬레이션 모델

THS3201 PSpice Model

SLOC004.ZIP (5 KB) - PSpice Model
계산 툴

ANALOG-ENGINEER-CALC — 아날로그 엔지니어의 계산기

The Analog Engineer’s Calculator is designed to speed up many of the repetitive calculations that analog circuit design engineers use on a regular basis. This PC-based tool provides a graphical interface with a list of various common calculations ranging from setting op-amp gain with feedback (...)
계산 툴

VOLT-DIVIDER-CALC — Voltage divider calculation tool

The voltage divider calculation tool (VOLT-DIVIDER-CALC) quickly determines a set of resistors for a voltage divider. This KnowledgeBase JavaScript utility can be used to find a set of resistors for a voltage divider to achieve the desired output voltage. VOLT-DIVIDER-CALC can also be used to (...)
시뮬레이션 툴

PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®

TI용 PSpice®는 아날로그 회로의 기능을 평가하는 데 사용되는 설계 및 시뮬레이션 환경입니다. 완전한 기능을 갖춘 이 설계 및 시뮬레이션 제품군은 Cadence®의 아날로그 분석 엔진을 사용합니다. 무료로 제공되는 TI용 PSpice에는 아날로그 및 전력 포트폴리오뿐 아니라 아날로그 행동 모델에 이르기까지 업계에서 가장 방대한 모델 라이브러리 중 하나가 포함되어 있습니다.

TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
시뮬레이션 툴

TINA-TI — SPICE 기반 아날로그 시뮬레이션 프로그램

TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
사용 설명서: PDF
패키지 CAD 기호, 풋프린트 및 3D 모델
HVSSOP (DGN) 8 Ultra Librarian
SOIC (D) 8 Ultra Librarian
SOT-23 (DBV) 5 Ultra Librarian

주문 및 품질

포함된 정보:
  • RoHS
  • REACH
  • 디바이스 마킹
  • 납 마감/볼 재질
  • MSL 등급/피크 리플로우
  • MTBF/FIT 예측
  • 물질 성분
  • 인증 요약
  • 지속적인 신뢰성 모니터링
포함된 정보:
  • 팹 위치
  • 조립 위치

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

콘텐츠는 TI 및 커뮤니티 기고자에 의해 "있는 그대로" 제공되며 TI의 사양으로 간주되지 않습니다. 사용 약관을 참조하십시오.

품질, 패키징, TI에서 주문하는 데 대한 질문이 있다면 TI 지원을 방문하세요. ​​​​​​​​​​​​​​

동영상