AFE4410
- Accurate, Continuous Heart-Rate Monitoring:
- Up to 100-dB Dynamic Range for Accurate Heart-Rate Detection
- Low Current for Continuous Operation on a Wearable Device With a Typical Value:
- 30 µA for an LED, 25 µA for the Receiver
- Transmitter:
- 4 LEDs in Common Anode Configurations
- 8-Bit Programmable LED Current to 200 mA
- Mode to Fire Two LEDs in Parallel
- Programmable LED On-Time
- Simultaneous Support of 3 LEDs for Optimized SpO2, HRM, or Multiwavelength HRM
- Average Current of 30 µA Adequate for a Typical Heart-Rate Monitoring Scenario:
- 20-mA Setting, 60-µs Pulse Duration,
25-Hz Sampling Rate
- 20-mA Setting, 60-µs Pulse Duration,
- Receiver:
- Supports 3 Time-Multiplexed PD Inputs
- 24-Bit Representation of Current Input From PD in Two’s-Complement Format
- Individual DC Offset Subtraction DAC
(Up to ±127-µA Range) at TIA Input for Each LED, Ambient - Digital Ambient Subtraction at ADC Output
- Transimpedance Gain: 10 kΩ to 2 MΩ
- Noise Filtering With Programmable Bandwidth
- Receiver Operates at Approximately 1-µA/Hz Sampling Rate (Example, 25 µA at 25 Hz)
- Hardware Power-Down Mode: Approximately 0-µA Current
- Flexible Pulse Sequencing and Timing Control
- Clocking Via External Clock or Internal Oscillator
- FIFO With 128-Sample Depth:
- Programmable Partitioning Across Phases
- Pin-Selectable I2C, SPI Interface
- Operating Temperature Range: –20°C to +70°C
- 2.6-mm × 2.1-mm, 0.4-mm Pitch DSBGA Package
- Supplies:
- Tx: 3 V to 5.25 V
- Rx: 1.8 V to 1.9 V (LDO Bypass),
2.0 V to 3.6 V (LDO Enabled) - IO: 1.7 V to Rx_SUP
TheAFE4410is an analog front-end for optical biosensing applications, such as heart rate monitoring (HRM). The device supports a maximum of four switching light-emitting diodes (LEDs) and a maximum of three photodiodes (PDs). The electrical current from the photodiode is converted into voltage by the transimpedance amplifier (TIA) and digitized using an analog-to-digital converter (ADC). The ADC code is stored in a 128-sample first-in, first-out block (FIFO) with programmable depth. The FIFO can be read out using either an I2C interface or a serial peripheral interface (SPI). The AFE also has a fully integrated LED driver with 8-bit current control. The device has high dynamic range transmit-and-receive circuitry offering a dynamic range of up to 100 dB that enables accurate heart ratesensing. The AFE achieves extremely low current levels by operating an ultralow power (ULP) mode set by using the ENABLE_ULP register bit.
![](https://www.ti.com/content/dam/ticom/images/icons/illustrative-icons/resources/information-icon.png)
추가 정보
NDA에 따라 전체 데이터시트 및 기타 설계 리소스를 사용할 수 있습니다. 지금 요청
기술 자료
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
AFE4403EVM — 심박수 모니터 및 펄스 옥시미터를 위한 AFE4403 통합 AFE 평가 모듈
The AFE4403EVM is intended for evaluating the AFE4403 device. The fully integrated AFE is ideally suited for Pulse Oximeter and Heart rate monitoring applications and consists of low noise receive channel, the LED transmit section and diagnostics for sensor and LED fault detection. The AFE4403 has (...)
AFE4410EVM — 웨어러블 광학 심박수 모니터링을 위한 FIFO가 포함된 AFE4410 통합 AFE 평가 모듈
AFE4410은 HRM(심박수 모니터링), SpO2(주변 모세혈관 산소포화도) 등과 같은 광학 바이오센싱 애플리케이션을 위한 AFE(아날로그 프론트 엔드)입니다. 이 장치는 스위칭 LED(발광 다이오드) 4개와 포토다이오드 3개를 지원합니다. 포토다이오드의 전류는 TIA(트랜스임피던스 증폭기)를 통해 전압으로 변환된 후 ADC(아날로그-디지털 컨버터)를 사용하여 디지털화됩니다. ADC 코드는 프로그래밍 가능한 깊이를 지원하는 128샘플 FIFO에 저장할 수 있습니다. 저장해야 하는 위상을 수용하도록 FIFO 깊이를 분할할 수 (...)
AFE4490SPO2EVM — 펄스 옥시미터를 위한 AFE4490 통합 아날로그 프론트 엔드(AFE) 평가 모듈
The AFE44x0SPO2EVM is intended for evaluating AFE4400 and AFE4490 devices. The family of devices are fully integrated AFE ideally suited for Pulse Oximeter applications and consist of low noise receive channel, the LED transmit section and diagnostics for sensor and LED fault detection. The (...)
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
---|---|---|
DSBGA (YZ) | 30 | Ultra Librarian |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.