產品詳細資料

Number of full bridges 2 Vs ABS (max) (V) 70 Full-scale current (A) 3 RDS(ON) (HS + LS) (mΩ) 300 Control mode STEP/DIR Control interface Hardware (GPIO), SPI Microstepping levels 256 Features Current Regulation, Integrated Current Sensing, Open-Load Detection, Smart Tune, Stall Detection Rating Catalog Operating temperature range (°C) -40 to 125
Number of full bridges 2 Vs ABS (max) (V) 70 Full-scale current (A) 3 RDS(ON) (HS + LS) (mΩ) 300 Control mode STEP/DIR Control interface Hardware (GPIO), SPI Microstepping levels 256 Features Current Regulation, Integrated Current Sensing, Open-Load Detection, Smart Tune, Stall Detection Rating Catalog Operating temperature range (°C) -40 to 125
HTSSOP (DDW) 44 113.4 mm² 14 x 8.1 HTSSOP (PWP) 28 62.08 mm² 9.7 x 6.4
  • Stepper Motor Driver
    • SPI or H/W Interface with STEP/DIR pins
    • Up to 1/256 Microstepping Indexer
  • 4.5 V to 65 V Operating Supply Voltage Range
    • Supports standard 24 V, 36 V and 48 V rails
  • Low R DS(ON): 300 mΩ HS + LS at 24 V, 25°C

  • High Current Capacity Per Bridge:
    • 3 A full-scale, 2.1 A RMS
  • DDW package pin-to-pin compatible with -
  • PWP package pin-to-pin compatible with -
  • Integrated current sensing and regulation
    • ± 6% full-scale current accuracy
  • Smart tune and mixed decay regulation options
  • Silent step Decay mode for silent operation at standstill and low speed
  • Automatic Microstepping mode for step frequency interpolation
  • Customizable microstepping indexer table
  • Auto-torque for load dependent current control
  • Standstill Power Saving mode
  • Supports 1.8-V, 3.3-V, 5.0-V logic inputs
  • Low-current sleep mode (2.5 µA)
  • Separate logic supply voltage ( VCC)
  • Protection and Diagnostic features
    • Sensorless Stall Detection
    • VM undervoltage lockout (UVLO)
    • Open-load Detection (OL)
    • Overcurrent protection (OCP)
    • Thermal shutdown (OTSD)
    • Fault condition output (nFAULT)
    • Indexer zero position output ( nHOME)
  • Stepper Motor Driver
    • SPI or H/W Interface with STEP/DIR pins
    • Up to 1/256 Microstepping Indexer
  • 4.5 V to 65 V Operating Supply Voltage Range
    • Supports standard 24 V, 36 V and 48 V rails
  • Low R DS(ON): 300 mΩ HS + LS at 24 V, 25°C

  • High Current Capacity Per Bridge:
    • 3 A full-scale, 2.1 A RMS
  • DDW package pin-to-pin compatible with -
  • PWP package pin-to-pin compatible with -
  • Integrated current sensing and regulation
    • ± 6% full-scale current accuracy
  • Smart tune and mixed decay regulation options
  • Silent step Decay mode for silent operation at standstill and low speed
  • Automatic Microstepping mode for step frequency interpolation
  • Customizable microstepping indexer table
  • Auto-torque for load dependent current control
  • Standstill Power Saving mode
  • Supports 1.8-V, 3.3-V, 5.0-V logic inputs
  • Low-current sleep mode (2.5 µA)
  • Separate logic supply voltage ( VCC)
  • Protection and Diagnostic features
    • Sensorless Stall Detection
    • VM undervoltage lockout (UVLO)
    • Open-load Detection (OL)
    • Overcurrent protection (OCP)
    • Thermal shutdown (OTSD)
    • Fault condition output (nFAULT)
    • Indexer zero position output ( nHOME)

The DRV8461 is a wide-voltage, high-power, high-performance stepper motor driver. The device supports up to 65-V supply voltage, and integrated MOSFETs with 300 mΩ HS + LS on-resistance allow up to 3-A current.

The auto-torque feature boosts efficiency by adjusting the coil current according to load torque. Standstill power saving mode reduces power loss during motor holding condition. Silent step decay mode delivers noiseless operation at low speeds and standstill. The internal current sense eliminates the need for sense resistors, saving PCB area and system cost. Built-in indexer supports up to 1/256 microstepping, and the automatic microstepping mode interpolates the input STEP signal to reduce overhead on the controller. Sensorless stall detection eliminates end stops from the system. The device supports other protection and diagnostic features for robust and reliable operation.

The DRV8461 requires minimal tuning to configure the advanced features. The DRV8461 supports higher power density compared to external FET drivers, with a smaller PCB area. High energy efficiency with precise, noiseless operation makes the DRV8461 an ideal choice for high-performance stepper systems.

The DRV8461 is a wide-voltage, high-power, high-performance stepper motor driver. The device supports up to 65-V supply voltage, and integrated MOSFETs with 300 mΩ HS + LS on-resistance allow up to 3-A current.

The auto-torque feature boosts efficiency by adjusting the coil current according to load torque. Standstill power saving mode reduces power loss during motor holding condition. Silent step decay mode delivers noiseless operation at low speeds and standstill. The internal current sense eliminates the need for sense resistors, saving PCB area and system cost. Built-in indexer supports up to 1/256 microstepping, and the automatic microstepping mode interpolates the input STEP signal to reduce overhead on the controller. Sensorless stall detection eliminates end stops from the system. The device supports other protection and diagnostic features for robust and reliable operation.

The DRV8461 requires minimal tuning to configure the advanced features. The DRV8461 supports higher power density compared to external FET drivers, with a smaller PCB area. High energy efficiency with precise, noiseless operation makes the DRV8461 an ideal choice for high-performance stepper systems.

下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
可直接投入的替代產品,相較於所比較的裝置,具備升級功能
DRV8462 現行 具有智慧型微調、熄火偵測和自動扭矩的 65V、10A 雙全橋步進馬達驅動器 Optimized for higher current applications (10-A FS)
引腳對引腳且具備與所比較裝置相同的功能
DRV8452 現行 具智慧型微調、熄火偵測和自動扭矩的 50-V、5-A 雙全橋步進馬達驅動器 Optimized for lower voltage applications (50 V abs max)
功能與所比較的裝置相似
DRV8262 現行 具整合式電流感測和穩壓功能的 65-V 單或雙全橋馬達驅動器 Single or dual H-bridge motor driver with PH/EN or PWM interface
DRV8962 現行 具電流感測輸出的 65-V 四通道半橋驅動器 Four channel driver with independent half-bridge control

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件,然後再試一次。
檢視所有 2
類型 標題 日期
* Data sheet DRV8461: 65 V, 3 A Stepper Motor Driver for High Efficiency and Noiseless Operation datasheet (Rev. A) PDF | HTML 2023年 9月 13日
Certificate DRV8461EVM EU RoHS Declaration of Conformity (DoC) 2022年 12月 13日

設計與開發

如需其他條款或必要資源,請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

DRV8461EVM — 適用 DDW 封裝的 DRV8461 評估模組

DRV8461 EVM 評估模組展示 DRV8461DDWR. 的功能和性能。

DRV8461 是完整整合的工業應用步進馬達驅動器。本裝置可透過 4.5-V 至 65-V 供電範圍運作,並可驅動高達 3-A 全刻度電流。

使用指南: PDF | HTML
TI.com 無法提供
支援軟體

DRV84XX-DRV89X2-DRV82X2-EVM-SOFTWARE EVM GUI and device firmware for DRV84XX_DRV89X2_DRV82X2 family

Zipped folder containing manifests and installers for both the GUI and the firmware of the DRV84XX_DRV89X2_DRV82X2 family of devices. Detailed instructions on how to use the GUI can be found in the User's Guide of the DRV84XX-DRV89X2-DRV82X2-EVM.
支援產品和硬體

支援產品和硬體

產品
有刷 DC (BDC) 馬達驅動器
DRV8952 具電流感測輸出的 50-V 四通道半橋驅動器 DRV8962 具電流感測輸出的 65-V 四通道半橋驅動器 DRV8262 具整合式電流感測和穩壓功能的 65-V 單或雙全橋馬達驅動器
步進馬達驅動器
DRV8462 具有智慧型微調、熄火偵測和自動扭矩的 65V、10A 雙全橋步進馬達驅動器 DRV8452 具智慧型微調、熄火偵測和自動扭矩的 50-V、5-A 雙全橋步進馬達驅動器 DRV8461 具智慧型微調、熄火偵測和自動扭矩的 65-V、3-A 雙全橋步進馬達驅動器
硬體開發
開發板
DRV8462EVM 具自動微步進、適用於步進馬達驅動器的 DRV8462 評估模組 DRV8262EVM 採用 DDW 封裝且適用於單或雙全橋馬達驅動器的 DRV8262 評估模組 DRV8962EVM 適用於具電流感測輸出之四路半橋馬達驅動器的 DRV8962 評估模組 DRV8461EVM 適用 DDW 封裝的 DRV8461 評估模組 DRV8462VEVM 採用 DDV 封裝的步進馬達驅動器 DRV8462 評估模組 DRV8262VEVM 採用 DDV 封裝且適用於單或雙全橋馬達驅動器的 DRV8262 評估模組 DRV8962VEVM 適用於採用 DDV 封裝的四路半橋馬達驅動器的 DRV8962 評估模組
啟動 下載選項
封裝 針腳 CAD 符號、佔位空間與 3D 模型
HTSSOP (DDW) 44 Ultra Librarian
HTSSOP (PWP) 28 Ultra Librarian

訂購與品質

內含資訊:
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊:
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

內容係由 TI 和社群貢獻者依「現狀」提供,且不構成 TI 規範。檢視使用條款

若有關於品質、封裝或訂購 TI 產品的問題,請參閱 TI 支援。​​​​​​​​​​​​​​

影片