比較対象デバイスと類似の機能
SN65MLVD205
- Low-Voltage Differential 30- up to 100 Mbps
- Power Dissipation at 100 Mbps
- Driver: 50 mW Typical
- Receiver: 30 mW Typical
- Meets or Exceeds Current Revision of M-LVDS Standard TIA/EIA–899 for Multipoint Data Interchange
- Controlled Driver Output Voltage Transition Times for Improved Signal Quality
- –1-V to 3.4-V Common-Mode Voltage Range Allows Data Transfer With up to 2 V of Ground Noise
- Type-1 Receivers Incorporate 25 mV of Hysteresis
- Type-2 Receivers Provide an Offset (100 mV) Threshold to Detect Open-Circuit and Idle-Bus Conditions
- Operates From a Single 3.3-V Supply
- Propagation Delay Times Typically 2.3 ns for Drivers and 5 ns for Receivers
- Power-Up/Down Glitch-Free Driver
- Driver Handles Operation Into a Continuous Short Circuit Without Damage
- Bus Pins High Impedance When Disabled or VCC ≤ 1.5V
- 200-Mbps Devices Available (SN65MLVD201, 203, 206, and 207)
The signaling rate of a line is the number of voltage transitions that are made per second expressed in bps (bits per second) units.
This series of SN65MLVD20x devices are low-voltage differential line drivers and receivers complying with the proposed multipoint low-voltage differential signaling (M-LVDS) standard (TIA/EIA899). These circuits are similar to their TIA/EIA-644 standard compliant LVDS counterparts, with added features to address multipoint applications. Driver output current has been increased to support doubly-terminated, 50- load multipoint applications. Driver output slew rates are optimized for signaling rates up to 100 Mbps.
Types 1 and 2 receivers are available. Both types of receivers operate over a common-mode voltage range of 1 V to 3.4 V to provide increased noise immunity in harsh electrical environments. Type-1 receivers have their differential input voltage thresholds near zero volts (±50 mV), and include 25 mV of hysteresis to prevent output oscillations in the presence of noise. Type-2 receivers include an offset threshold to detect open-circuit, idle-bus, and other fault conditions, and provide a known output state under these conditions.
The intended application of these devices is in half-duplex or multipoint baseband data transmission over controlled impedance media of approximately 100- characteristic impedance. The transmission media may be printed circuit board traces, backplanes, or cables. (Note: The ultimate rate and distance of data transfer is dependent upon the attenuation characteristics of the media, the noise coupling to the environment, and other application-specific characteristics).
These devices are characterized for operation from 40°C to 85°C.
技術資料
種類 | タイトル | 最新の英語版をダウンロード | 日付 | |||
---|---|---|---|---|---|---|
* | データシート | SN65MLVD200/2/4/5: Multipoint-LVDS Line Drivers and Receivers データシート (Rev. E) | 2003年 4月 25日 | |||
アプリケーション・ノート | Introduction to M-LVDS (TIA/EIA-899) (Rev. A) | 2013年 1月 3日 | ||||
ユーザー・ガイド | Multipoint-Low Voltage Differential Signaling (M-LVDS) EVM (Rev. B) | 2004年 4月 5日 | ||||
アプリケーション・ノート | M-LVDS Signaling Rate Versus Distance | 2003年 4月 9日 | ||||
アプリケーション・ノート | Interoperability of M-LVDS and BusLVDS | 2003年 2月 6日 | ||||
ユーザー・ガイド | 200 Mbps Multipoint-Low Voltage Differential Signaling (M-LVDS) EVM (Rev. A) | 2002年 12月 20日 | ||||
アプリケーション・ノート | Wired-Logic Signaling with M-LVDS | 2002年 10月 31日 | ||||
ユーザー・ガイド | Multipoint-Low Voltage Differential Signaling (M-LVDS) Evaluation Module | 2002年 3月 4日 | ||||
アプリケーション・ノート | TIA/EIA-485 and M-LVDS, Power and Speed Comparison | 2002年 2月 20日 |
設計および開発
その他のアイテムや必要なリソースを参照するには、以下のタイトルをクリックして詳細ページをご覧ください。
PSPICE-FOR-TI — TI Design / シミュレーション・ツール向け PSpice®
設計とシミュレーション向けの環境である PSpice for TI (...)
TINA-TI — SPICE ベースのアナログ・シミュレーション・プログラム
TINA-TI をインストールするには、約 500MB が必要です。インストールは簡単です。必要に応じてアンインストールも可能です。(そのようなことはないと思いますが)
TINA は DesignSoft (...)
パッケージ | ピン数 | CAD シンボル、フットプリント、および 3D モデル |
---|---|---|
SOIC (D) | 14 | Ultra Librarian |
購入と品質
- RoHS
- REACH
- デバイスのマーキング
- リード端子の仕上げ / ボールの原材料
- MSL 定格 / ピーク リフロー
- MTBF/FIT 推定値
- 使用原材料
- 認定試験結果
- 継続的な信頼性モニタ試験結果
- ファブの拠点
- 組み立てを実施した拠点