SN65LVDS95-EP
- Controlled Baseline
- One Assembly/Test Site, One Fabrication Site
- Enhanced Diminishing Manufacturing
Sources (DMS) Support - Enhanced Product-Change Notification
- Qualification Pedigree
- 21:3 Data Channel Compression at up to
1.36 Gigabits per Second Throughput - Suited for Point-to-Point Subsystem
Communication With Very Low EMI - 21 Data Channels Plus Clock in
Low-Voltage TTL and 3 Data Channels Plus
Clock Out Low-Voltage Differential - Operates From a Single 3.3-V Supply and
250 mW (Typ) - 5-V Tolerant Data Inputs
- ’LVDS95 Has Rising Clock Edge Triggered Inputs
- Bus Pins Tolerate 6-kV HBM ESD
- Packaged in Thin Shrink Small-Outline
Package With 20 Mil Terminal Pitch - Consumes <1 mW When Disabled
- Wide Phase-Lock Input Frequency Range
20 MHz to 68 MHz - No External Components Required for PLL
- Inputs Meet or Exceed the Requirements of
ANSI EIA/TIA-644 Standard - Industrial Temperature Qualified
TA = –40°C to 85°C - Replacement for the National DS90CR215
Component qualification in accordance with JEDEC and industry standards to ensure reliable operation over an extended temperature range. This includes, but is not limited to, Highly Accelerated Stress Test (HAST) or biased 85/85, temperature cycle, autoclave or unbiased HAST, electromigration, bond intermetallic life, and mold compound life. Such qualification testing should not be viewed as justifying use of this component beyond specified performance and environmental limits.
The SN65LVDS95 LVDS serdes (serializer/deserializer) transmitter contains three 7-bit parallel-load serial-out shift registers, a 7× clock synthesizer, and four low-voltage differential signaling (LVDS) line drivers in a single integrated circuit. These functions allow 21 bits of single-ended LVTTL data to be synchronously transmitted over 4 balanced-pair conductors for receipt by a compatible receiver, such as the SN65LVDS96.
When transmitting, data bits D0 through D20 are each loaded into registers of the SN65LVDS95 on the rising edge of the input clock signal (CLKIN). The frequency of CLKIN is multiplied seven times and then used to serially unload the data registers in 7-bit slices. The three serial streams and a phase-locked clock (CLKOUT) are then output to LVDS output drivers. The frequency of CLKOUT is the same as the input clock, CLKIN.
The SN65LVDS95 requires no external components and little or no control. The data bus appears the same at the input to the transmitter and output of the receiver with data transmission transparent to the user(s). The only user intervention is the possible use of the shutdown/clear (SHTDN) active-low input to inhibit the clock and shut off the LVDS output drivers for lower power consumption. A low level on this signal clears all internal registers to a low level.
기술 자료
| 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | SN65LVDS95-EP LVDS SERDES Transmitter datasheet (Rev. A) | 2009/09/24 | |
| * | VID | SN65LVDS95-EP VID V6204643 | 2016/06/21 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
TINA-TI — SPICE 기반 아날로그 시뮬레이션 프로그램
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| TSSOP (DGG) | 48 | Ultra Librarian |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치