TPS61261
- Input Voltage Range from 0.8 V to 4.0 V
- Up to 95% Efficiency
- 100 mA Output Current at 3.3 Vout (VIN > 1 V)
- Fixed and Adjustable Output Voltage Options from 1.8 V to 4.0 V
- Programmable Average Output Current from 10 mA to 100 mA
- Adjustable Output Current Limit for Smallest Inductor
- Power Save Mode for Improved Efficiency at Low Output Power
- 29-µA Quiescent Current
- Advanced Softstart
- Quasi Fixed Frequency Operation at 2.5 MHz
- Output Overvoltage Protection
- Load Disconnect During Shutdown
- Undervoltage Lockout
- Available in a 2.00 × 2.00 mm, 6-Pin WSON Package
The TPS6126x devices provide a power supply solution for products powered by either single or dual cell alkaline, NiCd, or NiMH batteries. Its unique advanced softstart makes it also suitable for products powered by high output impedance battery types, like coin cells. Output currents can go as high as 100 mA while using a single cell alkaline battery, and discharge it down to 0.8 V or lower.
The boost converter is based on a quasi fixed frequency, pulse-width-modulation (PWM) controller using synchronous rectification to obtain maximum efficiency. At low load currents, the converter enters Power Save Mode to ensure high efficiency over a wide load current range. The maximum average current in the switches is limited to a programmable value which can go as high as 700 mA. The output voltage is programmable using an external resistor divider, or is fixed internally on the chip. In addition, the average output current can be programmed as well. The converter then regulates the programmed output voltage or the programmed output current, which ever demands lower output power. The converter can be disabled to minimize battery drain. During shutdown, the load is disconnected from the battery. The device is packaged in a 6-pin WSON (DRV) package.
기술 자료
| 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | TPS6126x 0.8-V Input Synchronous Boost Converters with 100-mA Output Current datasheet (Rev. C) | PDF | HTML | 2018/04/23 |
| Application note | QFN and SON PCB Attachment (Rev. C) | PDF | HTML | 2023/12/06 | |
| Application note | Performing Accurate PFM Mode Efficiency Measurements (Rev. A) | 2018/12/11 | ||
| Selection guide | Power Management Guide 2018 (Rev. R) | 2018/06/25 | ||
| Application note | Five Steps to a Good PCB Layout of the Boost Converter | PDF | HTML | 2016/05/03 | |
| Application note | Design of UVLO for LM27313 (Rev. B) | 2014/04/08 | ||
| User guide | TPS6126X User's Guide (Rev. B) | 2013/09/12 | ||
| Analog Design Journal | IQ: What it is, what it isn’t, and how to use it | 2011/06/17 | ||
| User guide | TPS6126x, Low-Input Voltage, Boost Converter Evaluation Module | 2011/06/08 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
TPS61260EVM-673 — 출력 전압을 조정할 수 있는 TPS61260 소형 저입력 전압 부스트 컨버터용 평가 모듈
This user’s guide describes the TPS6126x evaluation module (EVM) and how to perform a stand-alone evaluation to allow the EVM to interface with the system and host. The TPS61260EVM-673 converter is programmed from the factory to deliver a 3.3-Vdc output voltage for a continuous load of up to (...)
TPS61261EVM-208 — TPS61261EVM-208 소형 저입력 전압 부스트 컨버터 평가 모듈 보드
Tiny Low Input Voltage Boost (Step-Up) Converter Evaluation Module Board - Step Up
This describes the characteristics, operation, and use of the Texas Instruments TPS61261 evaluation module (EVM). This EVM is designed to help the user easily evaluate and test the operation and functionality of the (...)| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| WSON (DRV) | 6 | Ultra Librarian |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치