ISOW1044

활성

DC/DC 전원이 통합된 저방출, 5kVrms 절연 CAN FD 트랜시버

제품 상세 정보

Rating Catalog Isolation rating Basic Number of channels 1 Data rate (max) (Mbps) 5 Working isolation voltage (VIOWM) (Vrms) 1000 Surge isolation voltage (VIOSM) (VPK) 6250, 7800, 10000 Transient isolation voltage (VIOTM) (VPK) 7071 Withstand isolation voltage (VISO) (Vrms) 5000 CMTI (min) (kV/µs) 85 Operating temperature range (°C) -40 to 125 Type CAN
Rating Catalog Isolation rating Basic Number of channels 1 Data rate (max) (Mbps) 5 Working isolation voltage (VIOWM) (Vrms) 1000 Surge isolation voltage (VIOSM) (VPK) 6250, 7800, 10000 Transient isolation voltage (VIOTM) (VPK) 7071 Withstand isolation voltage (VISO) (Vrms) 5000 CMTI (min) (kV/µs) 85 Operating temperature range (°C) -40 to 125 Type CAN
SOIC (DFM) 20 132.149 mm² 12.83 x 10.3
  • Meets the requirements of ISO 11898-2:2016 physical layer standards
    • Support of Classical CAN: 1 Mbps

    • Optimized for CAN FD: 2 and 5 Mbps
  • Integrated DC-DC converter with low-emissions, low-noise
    • Meets CISPR 32 and EN 55032 Class B with greater than 6 dB margin on a two-layer PCB
    • Low frequency power converter at 25 MHz enabling low noise performance
  • Additional 10 Mbps GPIO channel
  • High efficiency output power
    • Typical efficiency: 47%
    • Isolated output voltage accuracy: ± 5%
    • Additional output current: 20 mA
  • Independent power supply for CAN & DC-DC
    • Logic supply (V IO): 1.71 V to 5.5 V
    • Power converter supply ( V DD): 4.5 V to 5.5 V
  • Fault-Protected CAN FD Transceiver
    • DC Bus fault protection voltage: ± 58V
    • Receiver common mode input voltage: ±12 V
    • Remote wakeup via BUS wake-up pattern
  • Typical loop delay: 167 ns
  • Reinforced and Basic isolation options
  • High CMTI: 100-kV/µs (typical)
  • High ESD bus protection w.r.t GND2
    • HBM ESD: ±12 kV
    • IEC 61000-4-2 contact discharge: ±8 kV
  • Operating temperature range: -40°C to 125°C
  • Current limit and thermal shutdown
  • 20-pin wide SOIC package
  • Safety-Related Certifications planned:
    • VDE Reinforced and Basic insulation per DIN VDE V 0884-11:2017-01
    • UL 1577 component recognition program
    • IEC 62368-1, IEC 61010-1, IEC 60601-1 and GB 4943.1-2011 certifications
  • Meets the requirements of ISO 11898-2:2016 physical layer standards
    • Support of Classical CAN: 1 Mbps

    • Optimized for CAN FD: 2 and 5 Mbps
  • Integrated DC-DC converter with low-emissions, low-noise
    • Meets CISPR 32 and EN 55032 Class B with greater than 6 dB margin on a two-layer PCB
    • Low frequency power converter at 25 MHz enabling low noise performance
  • Additional 10 Mbps GPIO channel
  • High efficiency output power
    • Typical efficiency: 47%
    • Isolated output voltage accuracy: ± 5%
    • Additional output current: 20 mA
  • Independent power supply for CAN & DC-DC
    • Logic supply (V IO): 1.71 V to 5.5 V
    • Power converter supply ( V DD): 4.5 V to 5.5 V
  • Fault-Protected CAN FD Transceiver
    • DC Bus fault protection voltage: ± 58V
    • Receiver common mode input voltage: ±12 V
    • Remote wakeup via BUS wake-up pattern
  • Typical loop delay: 167 ns
  • Reinforced and Basic isolation options
  • High CMTI: 100-kV/µs (typical)
  • High ESD bus protection w.r.t GND2
    • HBM ESD: ±12 kV
    • IEC 61000-4-2 contact discharge: ±8 kV
  • Operating temperature range: -40°C to 125°C
  • Current limit and thermal shutdown
  • 20-pin wide SOIC package
  • Safety-Related Certifications planned:
    • VDE Reinforced and Basic insulation per DIN VDE V 0884-11:2017-01
    • UL 1577 component recognition program
    • IEC 62368-1, IEC 61010-1, IEC 60601-1 and GB 4943.1-2011 certifications

The ISOW1044 device is a galvanically-isolated controller area network (CAN) transceiver with a built-in isolated DC-DC converter that eliminates the need for a separate isolated power supply in space-constrained isolated designs. The low-emissions, isolated DC-DC meets CISPR 32 radiated emissions Class B standard with just two ferrite beads on a simple two-layer PCB. Additional 20 mA output current can be used to power other circuits on the board. An integrated 10 Mbps GPIO channel is available and can help remove an additional digital isolator or optocoupler for diagnotstics, LED indication or supply monitoring.

The ISOW1044 device is a galvanically-isolated controller area network (CAN) transceiver with a built-in isolated DC-DC converter that eliminates the need for a separate isolated power supply in space-constrained isolated designs. The low-emissions, isolated DC-DC meets CISPR 32 radiated emissions Class B standard with just two ferrite beads on a simple two-layer PCB. Additional 20 mA output current can be used to power other circuits on the board. An integrated 10 Mbps GPIO channel is available and can help remove an additional digital isolator or optocoupler for diagnotstics, LED indication or supply monitoring.

다운로드 스크립트와 함께 비디오 보기 동영상

기술 자료

star =TI에서 선정한 이 제품의 인기 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하십시오.
18개 모두 보기
유형 직함 날짜
* Data sheet ISOW1044 Isolated CAN FD Transceiver with Integrated Low-Emissions, Low-Noise, High-Efficiency DC-DC Converter datasheet (Rev. A) PDF | HTML 2021/11/08
Application note Top Design Questions About Isolated CAN Bus Design (Rev. B) PDF | HTML 2024/10/24
White paper 신뢰할 수 있는 합리적 가격대의 절연 기술 개발과 관련한 고전압 설계 문제의 해결 (Rev. C) PDF | HTML 2024/05/16
Certificate VDE Certificate for Reinforced Isolation for DIN EN IEC 60747-17 (Rev. S) 2024/02/29
Certificate VDE Certificate for Basic Isolation for DIN EN IEC 60747-17 (Rev. W) 2024/01/31
Certificate CQC Certificate for ISOxxDFM (Rev. A) 2023/03/27
Certificate CSA Certificate for ISOW1044xDFM (Rev. A) 2023/02/13
Product overview Isolating a CAN Bus (Rev. A) PDF | HTML 2023/01/13
Certificate TUV Certificate for Isolation Devices (Rev. K) 2022/08/05
Certificate UL Certificate of Compliance File E181974 Vol 4 Sec 6 (Rev. P) 2022/08/05
Application brief Isolate Your CAN Systems Without Compromising on Performance or Space (Rev. F) PDF | HTML 2022/08/04
White paper Why are Digital Isolators Certified to Meet Electrical Equipment Standards? 2021/11/16
White paper Distance Through Insulation: How Digital Isolators Meet Certification Requiremen PDF | HTML 2021/06/11
Technical article 4 common questions when isolating signal and power PDF | HTML 2021/06/01
Application brief How to Meet CISPR 32 Radiated Emissions Limits With ISOW7741 PDF | HTML 2021/05/28
Application brief Benefits of an Isolated CAN Transceiver with Integrated Power PDF | HTML 2021/05/25
Application brief How to Isolate Signal and Power in Isolated CAN Systems (Rev. C) PDF | HTML 2021/05/25
User guide ISOW1044 Reinforced 5-kVrms Isoated CAN Transceiver with Integrated Low-Emission PDF | HTML 2021/03/23

설계 및 개발

추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.

평가 보드

ISOW1044DFMEVM — DC-DC 컨버터가 통합된 ISOW1044 절연 CAN 트랜시버 평가 모듈

ISOW1044DFMEVM은 20핀 WB SOIC 패키지(패키지 코드-DFM)의 고효율, 저방출 DC-DC 컨버터 ISOW1044가 통합된 고성능, 5000VRMS 강화 절연 CAN 트랜시버를 평가하는 데 사용되는 평가 모듈(EVM)입니다. EVM에는 최소한의 외부 부품으로 장치를 평가할 수 있는 충분한 테스트 포인트 및 점퍼 옵션이 있습니다.

사용 설명서: PDF | HTML
TI.com에서 구매 불가
시뮬레이션 모델

ISOW1044 IBIS Model

SLLM489.ZIP (90 KB) - IBIS Model
레퍼런스 디자인

TIDA-010938 — 배터리 에너지 저장 시스템 레퍼런스 설계가 포함된 10kW, GaN 기반 단상 스트링 인버터

이 레퍼런스 설계는 두 개의 스트링 입력을 갖춘 단상 스트링 인버터로, 각각 80V에서 500V의 배터리 스택을 처리할 수 있는 에너지 저장 시스템 포트를 하나씩 처리합니다. 스트링 입력에서 배터리 저장 시스템까지 정격 전력은 최대 10kW입니다. 구성 가능한 AC/DC 컨버터는 230V에서 단상 그리드 연결로 최대 3.6kW를 처리할 수 있습니다.
Design guide: PDF
패키지 CAD 기호, 풋프린트 및 3D 모델
SOIC (DFM) 20 Ultra Librarian

주문 및 품질

포함된 정보:
  • RoHS
  • REACH
  • 디바이스 마킹
  • 납 마감/볼 재질
  • MSL 등급/피크 리플로우
  • MTBF/FIT 예측
  • 물질 성분
  • 인증 요약
  • 지속적인 신뢰성 모니터링
포함된 정보:
  • 팹 위치
  • 조립 위치

권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

콘텐츠는 TI 및 커뮤니티 기고자에 의해 "있는 그대로" 제공되며 TI의 사양으로 간주되지 않습니다. 사용 약관을 참조하십시오.

품질, 패키징, TI에서 주문하는 데 대한 질문이 있다면 TI 지원을 방문하세요. ​​​​​​​​​​​​​​

동영상