TPD1S414
- Overvoltage Protection at VBUS_CON Up to 30-V DC
- Low RON nFET Switch Supports Host and Charging Mode
- Internal 15-ms Start-Up Delay
- Internal 30-ms Soft-Start Delay to Minimize the USB Inrush Current
- Transient Protection for VBUS Line:
- IEC 61000-4-2 Contact Discharge ±15 kV
- IEC 61000-4-2 Air Gap Discharge ±15 kV
- IEC 61000-4-5 Open-Circuit Voltage 100 V
- Integrated Input Enable and Status Output Signal
- Thermal Shutdown (TSD) Feature
- Space-Saving DSBGA Package: (1.4 mm × 1.89 mm)
The TPD1S414 device is a single-chip solution for a USB connector’s VBUS line protection. The bidirectional nFET switch ensures safe current flow in both charging and host mode while protecting the internal system circuits from any overvoltage conditions at the VBUS_CON pin. On the VBUS_CON pin, this device can handle overvoltage protection up to 30 V. After the EN pin toggles low, the TPD1S414 waits 20 ms before turning ON the nFET through a soft-start delay. ACK pin indicates the FET is completely turned ON.
The typical application interface for the TPD1S414 is the VBUS line in USB connectors. Typical end equipment for TPD1S414 are mobiles phones, tablets, wearables, and electronic-point-of-sale (EPOS). The TPD1S414 can also be applied to any system using an interface with a 5-V power rail.
기술 자료
유형 | 직함 | 날짜 | ||
---|---|---|---|---|
* | Data sheet | TPD1S414 USB Charger Overvoltage, Surge, and ESD Protection for VBUS Pin datasheet (Rev. B) | PDF | HTML | 2015/11/29 |
User guide | Reading and Understanding an ESD Protection Data Sheet (Rev. A) | PDF | HTML | 2023/09/19 | |
Selection guide | System-Level ESD Protection Guide (Rev. D) | 2022/09/07 | ||
Application note | ESD Protection Layout Guide (Rev. A) | PDF | HTML | 2022/04/07 | |
White paper | Designing USB for short-to-battery tolerance in automotive environments | 2016/02/10 | ||
EVM User's guide | TPD1S414EVM User's Guide (Rev. A) | 2015/06/02 | ||
Analog Design Journal | Design Considerations for System-Level ESD Circuit Protection | 2012/09/25 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
TPD1S414EVM — TPD1S414EVM - ESD를 사용한 USB 충전기 과전압 OVP 스위치 평가 모듈
The TPD1S414EVM includes 4 TPD1S414YZ’s in various configurations for testing. Three of the TPD1S414YZ’s are configured for IEC61000-4-5 (8/20 μs) compliance testing; one TPD1S414YZ is configured for throughput on USB 2.0 Type A connectors for throughput analysis.
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
TINA-TI — SPICE 기반 아날로그 시뮬레이션 프로그램
패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
---|---|---|
DSBGA (YZ) | 12 | Ultra Librarian |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치