TPS61060
- LED Driver With Integrated Overvoltage
and Short-Circuit Protection - 2.7-V to 6-V Input Voltage Range
- 500-mV/250-mV Feedback Voltage
- TPS61060 Powers Up to 3 LEDs
- TPS61061 Powers Up to 4 LEDs
- TPS61062 Powers Up to 5 LEDs
- PWM Brightness Control on Enable
- Digital Brightness Control on ILED
- 1-MHz Fixed Switching Frequency
- 400-mA Internal Power MOSFET Switch
- LEDs Disconnected During Shutdown
- Operates With Small-Output Capacitors
Down to 220 nF - Up to 80% Efficiency
- 8-Pin NanoFree® Package (Chipscale, CSP)
- 3 × 3-mm QFN Package
The TPS6106x is a high-frequency, synchronous boost converter with constant current output to drive up to 5 white LEDs. For maximum safety, the device features integrated overvoltage and an advanced short-circuit protection when the output is shorted to ground. The device operates with 1-MHz fixed switching frequency to allow for the use of small external components and to simplify possible EMI problems. The device comes with three different overvoltage protection thresholds (14 V/18 V/23 V) to allow inexpensive and small-output capacitors with lower voltage ratings. The LED current is initially set with the external sense resistor Rs, and the feedback voltage is regulated to 500 mV or 250 mV, depending on the ILED pin configuration. Digital brightness control is implemented by applying a simple digital signal to the ILED pin. Alternatively, a PWM signal up to 1 kHz can be applied to the enable pin to control the LED brightness. During shutdown, the output is disconnected from the input to avoid leakage current through the LEDs.
기술 자료
| 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | TPS6106x Constant Current LED Driver With Digital and PWM Brightness Control datasheet (Rev. B) | PDF | HTML | 2014/12/09 |
| White paper | Common LED Functions and LED Driver Design Considerations | 2020/09/21 | ||
| Application note | Performing Accurate PFM Mode Efficiency Measurements (Rev. A) | 2018/12/11 | ||
| Selection guide | Power Management Guide 2018 (Rev. R) | 2018/06/25 | ||
| Application note | Optimizing Transient Response of Internally Compensated DC-DC Converters (Rev. B) | 2017/11/29 | ||
| Application note | Extending the Soft Start Time Without a Soft Start Pin (Rev. B) | 2017/06/15 | ||
| EVM User's guide | TPS6106xEVM User's Guide (Rev. A) | 2007/04/11 | ||
| Application note | Minimizing Ringing at the Switch Node of a Boost Converter | 2006/09/15 | ||
| Application note | TPS61060/61/62: Single-Wire Digital Brightness Control | 2006/05/05 | ||
| More literature | Seminar 400 Topic 1 - Current-Mode Control of Switching Power Supplies | 2001/02/15 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
| 패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
|---|---|---|
| DSBGA (YZF) | 8 | Ultra Librarian |
| VSON (DRB) | 8 | Ultra Librarian |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치