전원 관리 AC/DC 및 DC/DC 컨트롤러(외장 FET)

UCC28710

활성

PSR, 밸리 스위칭 및 프로그래머블 케이블 보상을 지원하는 정전압, 정전류 PWM

제품 상세 정보

Vin (min) (V) 21 Vin (max) (V) 450 Iout (max) (A) 5 Operating temperature range (°C) -40 to 125 Control mode Primary-side regulation Topology Buck, Flyback Rating Catalog Vout (min) (V) 3.3 Vout (max) (V) 24 Features CC/CV output regulation, DCM, Green mode, High voltage startup, High-voltage startup, Input line monitor, Leading edge blanking, Light load efficiency, Light-load efficiency, Low power, Overcurrent protection, PSR, Primary-side regulated, Quasi-Resonant, Soft start, Valley switching Iq (typ) (µA) 2000 Duty cycle (max) (%) 99
Vin (min) (V) 21 Vin (max) (V) 450 Iout (max) (A) 5 Operating temperature range (°C) -40 to 125 Control mode Primary-side regulation Topology Buck, Flyback Rating Catalog Vout (min) (V) 3.3 Vout (max) (V) 24 Features CC/CV output regulation, DCM, Green mode, High voltage startup, High-voltage startup, Input line monitor, Leading edge blanking, Light load efficiency, Light-load efficiency, Low power, Overcurrent protection, PSR, Primary-side regulated, Quasi-Resonant, Soft start, Valley switching Iq (typ) (µA) 2000 Duty cycle (max) (%) 99
SOIC (D) 7 29.4 mm² 4.9 x 6
  • < 10-mW No-Load Power
  • Primary-Side Regulation (PSR) Eliminates Opto-Coupler
  • ±5% Voltage and Current Regulation Across Line and Load
  • 700-V Start-Up Switch
  • 100-kHz Maximum Switching Frequency Enables High-Power Density Charger Designs
  • Resonant Valley-Switching Operation for Highest Overall Efficiency
  • Frequency Jitter to Ease EMI Compliance
  • Wide VDD Range Allows Small Bias Capacitor
  • Clamped Gate-Drive Output for MOSFET
  • Overvoltage, Low-Line, and Overcurrent Protection Functions
  • Programmable Cable Compensation (UCC28710)
  • NTC Resistor Interface (UCC28711, UCC28712 and UCC28713) with Fixed Cable Compensation Options
  • SOIC-7 Package
  • Create a Custom Design Using the UCC28710 With the WEBENCH® Power Designer
  • < 10-mW No-Load Power
  • Primary-Side Regulation (PSR) Eliminates Opto-Coupler
  • ±5% Voltage and Current Regulation Across Line and Load
  • 700-V Start-Up Switch
  • 100-kHz Maximum Switching Frequency Enables High-Power Density Charger Designs
  • Resonant Valley-Switching Operation for Highest Overall Efficiency
  • Frequency Jitter to Ease EMI Compliance
  • Wide VDD Range Allows Small Bias Capacitor
  • Clamped Gate-Drive Output for MOSFET
  • Overvoltage, Low-Line, and Overcurrent Protection Functions
  • Programmable Cable Compensation (UCC28710)
  • NTC Resistor Interface (UCC28711, UCC28712 and UCC28713) with Fixed Cable Compensation Options
  • SOIC-7 Package
  • Create a Custom Design Using the UCC28710 With the WEBENCH® Power Designer

The UCC2871x family of flyback power supply controllers provides isolated-output Constant-Voltage (CV) and Constant-Current (CC) output regulation without the use of an optical coupler. The devices process information from the primary power switch and an auxiliary flyback winding for precise control of output voltage and current.

An internal 700-V start-up switch, dynamically-controlled operating states and a tailored modulation profile support ultra-low standby power without sacrificing start-up time or output transient response.

Control algorithms in the UCC28710 family allow operating efficiencies to meet or exceed applicable standards. The output drive interfaces to a MOSFET power switch. Discontinuous conduction mode (DCM) with valley switching reduces switching losses. Modulation of switching frequency and primary current peak amplitude (FM and AM) keeps the conversion efficiency high across the entire load and line ranges.

The controllers have a maximum switching frequency of 100 kHz and always maintain control of the peak-primary current in the transformer. Protection features help keep primary and secondary component stresses in check. The UCC28710 allow the cable compensation to be programmed. The UCC28711, UCC28712 and UCC28713 devices allow remote temperature sensing using a negative temperature coefficient (NTC) resistor while providing fixed cable-compensation levels.

The UCC2871x family of flyback power supply controllers provides isolated-output Constant-Voltage (CV) and Constant-Current (CC) output regulation without the use of an optical coupler. The devices process information from the primary power switch and an auxiliary flyback winding for precise control of output voltage and current.

An internal 700-V start-up switch, dynamically-controlled operating states and a tailored modulation profile support ultra-low standby power without sacrificing start-up time or output transient response.

Control algorithms in the UCC28710 family allow operating efficiencies to meet or exceed applicable standards. The output drive interfaces to a MOSFET power switch. Discontinuous conduction mode (DCM) with valley switching reduces switching losses. Modulation of switching frequency and primary current peak amplitude (FM and AM) keeps the conversion efficiency high across the entire load and line ranges.

The controllers have a maximum switching frequency of 100 kHz and always maintain control of the peak-primary current in the transformer. Protection features help keep primary and secondary component stresses in check. The UCC28710 allow the cable compensation to be programmed. The UCC28711, UCC28712 and UCC28713 devices allow remote temperature sensing using a negative temperature coefficient (NTC) resistor while providing fixed cable-compensation levels.

다운로드 스크립트와 함께 비디오 보기 동영상

관심 가지실만한 유사 제품

open-in-new 대안 비교
비교 대상 장치와 동일한 기능을 지원하는 핀 대 핀
UCC28712 활성 PSR, 밸리 스위칭, NTC 옵션 및 150mV 케이블 보상을 지원하는 정전압, 정전류 PWM Cable compensation threshold is 150 mV

기술 자료

star =TI에서 선정한 이 제품의 인기 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하십시오.
11개 모두 보기
유형 직함 날짜
* Data sheet UCC2871x Constant-Voltage, Constant-Current Controller With Primary-Side Regulation datasheet (Rev. C) PDF | HTML 2017/06/30
Application note Flyback Aux Winding OVP and UVLO Fault Sensing Design and Troubleshooting Tips PDF | HTML 2021/08/31
More literature PCB layout guidelines to optimize power supply performance 2021/03/23
White paper Power Electronics in Motor Drives: Where is it? (Rev. A) 2019/10/01
Application note Minimize Standby Consumption for UCC287XX Family 2019/08/01
Selection guide Power Management Guide 2018 (Rev. R) 2018/06/25
Application note Troubleshooting TI PSR controllers 2016/10/03
White paper Control Challenges for Low Power AC/DC Converters 2015/10/02
White paper Control Challenges for Low Power AC/DC Converters (PPT) 2015/10/02
Technical article Designing multiple output converters with primary side sensing PDF | HTML 2015/08/04
More literature Exposing the Inner Behavior of a Quasi-Resonant Flyback Converter 2013/10/29

설계 및 개발

추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.

평가 보드

UCC24630EVM-636 — UCC24630 65W AC/DC 어댑터

This is a high efficiency 65W AC/DC design using UCC24630 Synchronous Rectification Controller for a Universal input (85Vac to 265Vac) to 19.5V @3.33A output exceeding CoC-5 Tier2 and DOE Level VI performance requirements for external power supplies.

사용 설명서: PDF
TI.com에서 구매 불가
평가 보드

UCC28711EVM-160 — UCC28711 평가 모듈

The Texas Instruments UCC28711EVM-160 evaluation module (EVM) helps designers evaluate the performance of the UCC28711 Constant-Voltage, Constant-Current PWM with Primary-Side Regulation. The 5W EVM is used for evaluating an off line adapter for USB applications. It converts a 90V to 265V RMS (...)
사용 설명서: PDF
TI.com에서 구매 불가
평가 보드

UCC28720EVM-212 — USB 오프라인 어댑터를 위한 UCC28720EVM-212 5W 평가 모듈

The UCC28720EVM-212 is a 5W evaluation module for evaluating an off line adapter for USB applications. It is intended for evaluation purposes and is not intended to be an end product. The UCC28720EVM-212 converters 100V to 240V RMS input voltage down to 5V DC, with a 1A current limit for USB (...)
사용 설명서: PDF
TI.com에서 구매 불가
평가 보드

UCC28740EVM-525 — UCC28740EVM-525 평가 모듈

The UCC28740EVM-525 evaluation module is a 10W off-line discontinuous mode (DCM) flyback converter that provides constant-voltage (CV) and constant-current (CC) output regulation. It uses optical coupler feedback for tight voltage regulation and improved the transient response to large load steps (...)

사용 설명서: PDF
TI.com에서 구매 불가
시뮬레이션 모델

UCC2871x PSpice Transient Model

SLUM464.ZIP (17619 KB) - PSpice Model
시뮬레이션 모델

UCC2871x TINA-TI Transient Reference Design

SLUM539.TSC (224 KB) - TINA-TI Reference Design
시뮬레이션 모델

UCC2871x TINA-TI Transient Spice Model

SLUM538.ZIP (119 KB) - TINA-TI Spice Model
계산 툴

SLUC590 UCC2871x Calculator

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

제품
AC/DC 및 DC/DC 컨트롤러(외장 FET)
UCC28710 PSR, 밸리 스위칭 및 프로그래머블 케이블 보상을 지원하는 정전압, 정전류 PWM UCC28711 PSR, 밸리 스위칭, NTC 옵션 및 0mV 케이블 보상을 지원하는 정전압, 정전류 PWM UCC28712 PSR, 밸리 스위칭, NTC 옵션 및 150mV 케이블 보상을 지원하는 정전압, 정전류 PWM UCC28713 PSR, 밸리 스위칭, NTC 옵션 및 300mV 케이블 보상을 지원하는 정전압, 정전류 PWM

많은 TI 레퍼런스 설계에는 UCC28710이(가) 포함됩니다.

레퍼런스 디자인 선택 툴을 사용하여 애플리케이션 및 매개 변수에 가장 적합한 설계를 검토하고 식별할 수 있습니다.

패키지 CAD 기호, 풋프린트 및 3D 모델
SOIC (D) 7 Ultra Librarian

주문 및 품질

포함된 정보:
  • RoHS
  • REACH
  • 디바이스 마킹
  • 납 마감/볼 재질
  • MSL 등급/피크 리플로우
  • MTBF/FIT 예측
  • 물질 성분
  • 인증 요약
  • 지속적인 신뢰성 모니터링
포함된 정보:
  • 팹 위치
  • 조립 위치

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

콘텐츠는 TI 및 커뮤니티 기고자에 의해 "있는 그대로" 제공되며 TI의 사양으로 간주되지 않습니다. 사용 약관을 참조하십시오.

품질, 패키징, TI에서 주문하는 데 대한 질문이 있다면 TI 지원을 방문하세요. ​​​​​​​​​​​​​​

동영상