LM27402

現行

具 DCR 的 3-V 至 20-V 電壓模式同步降壓控制器

立即訂購

產品規格表

document-pdfAcrobat LM27402 High-Performance Synchronous Buck Controller With DCR Current Sensing datasheet (Rev. K) (英文) PDF | HTML

LM27402

現行

產品規格表

立即訂購

產品詳細資料

Vin (min) (V)

3

Vin (max) (V)

20

Iout (max) (A)

30

Operating temperature range (°C)

-40 to 125

Control mode

Voltage mode

Topology

Buck

Rating

Catalog

Vout (min) (V)

0.6

Vout (max) (V)

18.6

Features

Enable, Frequency synchronization, Power good, Pre-Bias Start-Up, Synchronous Rectification, Tracking

Iq (typ) (µA)

4500

Duty cycle (max) (%)

95

Number of phases

1

Vin (min) (V)

3

Vin (max) (V)

20

Iout (max) (A)

30

Operating temperature range (°C)

-40 to 125

Control mode

Voltage mode

Topology

Buck

Rating

Catalog

Vout (min) (V)

0.6

Vout (max) (V)

18.6

Features

Enable, Frequency synchronization, Power good, Pre-Bias Start-Up, Synchronous Rectification, Tracking

Iq (typ) (µA)

4500

Duty cycle (max) (%)

95

Number of phases

1

HTSSOP (PWP)

16

32 mm² 5 x 6.4

WQFN (RUM)

16

16 mm² 4 x 4

Wide Input-Voltage Range of 3 V to 20 V
Inductor DCR or Shunt Resistor Based Overcurrent Protection
0.6-V Reference With ±1% FB Accuracy Across Full –40°C to 125°C Junction Temperature Range
Switching Frequency from 200 kHz to 1.2 MHz
Output Voltage as High as 95% of Input Voltage
Integrated High-Current MOSFET Drivers
Internal VDD Bias Supply LDO Subregulator
External Clock Synchronization
Adjustable Soft Start With External Capacitor
Prebiased Start-up Capability
Power Supply Tracking
Voltage-Mode Control With Line Feedforward
Open-Drain Power-Good Indicator
Precision Enable With Hysteresis
16-Pin HTSSOP and WQFN Packages
Create a Custom Design Using the LM27402 With the WEBENCH^® Power Designer

Wide Input-Voltage Range of 3 V to 20 V
Inductor DCR or Shunt Resistor Based Overcurrent Protection
0.6-V Reference With ±1% FB Accuracy Across Full –40°C to 125°C Junction Temperature Range
Switching Frequency from 200 kHz to 1.2 MHz
Output Voltage as High as 95% of Input Voltage
Integrated High-Current MOSFET Drivers
Internal VDD Bias Supply LDO Subregulator
External Clock Synchronization
Adjustable Soft Start With External Capacitor
Prebiased Start-up Capability
Power Supply Tracking
Voltage-Mode Control With Line Feedforward
Open-Drain Power-Good Indicator
Precision Enable With Hysteresis
16-Pin HTSSOP and WQFN Packages
Create a Custom Design Using the LM27402 With the WEBENCH^® Power Designer

The LM27402 is a voltage-mode, synchronous, DC/DC step-down controller with lossless inductor DCR current sensing capability. Sensing the inductor current eliminates the need to add resistive powertrain elements, which increases overall efficiency and facilitates accurate, continuous current sensing. A 0.6-V ±1% voltage reference enables high accuracy and low voltage capability at the output. An input operating voltage range of 3 V to 20 V makes the LM27402 suitable for a large variety of input rails.

The LM27402 voltage-mode control loop incorporates input voltage feed forward to maintain stability throughout the entire input-voltage range. The switching frequency is adjustable from 200 kHz to
1.2 MHz. Dual, high-current, integrated MOSFET drivers support large Q_G, low R_DS(on) power MOSFETs. A power-good indicator provides power-rail-sequencing capability and output fault detection. An adjustable external soft start limits inrush current and provides monotonic output control during start-up. Other features include external tracking of other power supplies, integrated LDO bias supply, and synchronization capability.

The LM27402 is a voltage-mode, synchronous, DC/DC step-down controller with lossless inductor DCR current sensing capability. Sensing the inductor current eliminates the need to add resistive powertrain elements, which increases overall efficiency and facilitates accurate, continuous current sensing. A 0.6-V ±1% voltage reference enables high accuracy and low voltage capability at the output. An input operating voltage range of 3 V to 20 V makes the LM27402 suitable for a large variety of input rails.

The LM27402 voltage-mode control loop incorporates input voltage feed forward to maintain stability throughout the entire input-voltage range. The switching frequency is adjustable from 200 kHz to
1.2 MHz. Dual, high-current, integrated MOSFET drivers support large Q_G, low R_DS(on) power MOSFETs. A power-good indicator provides power-rail-sequencing capability and output fault detection. An adjustable external soft start limits inrush current and provides monotonic output control during start-up. Other features include external tracking of other power supplies, integrated LDO bias supply, and synchronization capability.

filter

尋找其它 AC/DC 和 DC/DC 控制器 (外部 FET)

下載觀看有字幕稿的影片影片

技術文件

star

=TI 所選的此產品重要文件

找不到結果。請清除您的搜尋條件，然後再試一次。

檢視所有 11

	類型	標題		日期
*	Data sheet	LM27402 High-Performance Synchronous Buck Controller With DCR Current Sensing datasheet (Rev. K)	PDF \| HTML	2018年 2月 23日
	Certificate	LM27402SQEVAL EU RoHS Declaration of Conformity (DoC) (Rev. A)		2022年 3月 8日
	User guide	LM27402 Buck Controller Evaluation Module User's Guide (Rev. C)	PDF \| HTML	2022年 1月 10日
	Selection guide	Power Management Guide 2018 (Rev. R)		2018年 6月 25日
	Analog Design Journal	Common mistakes made in controller designs for power converters		2018年 3月 26日
	Application brief	Using DC/DC Controllers to Improve Bitcoin Miner Designs		2018年 3月 15日
	Analog Design Journal	Reduce buck-converter EMI and voltage stress by minimizing inductive parasitics		2016年 7月 21日
	Technical article	High Density PCB Layout of DC/DC Converters, Part 2	PDF \| HTML	2015年 9月 16日
	Technical article	High Density PCB Layout of DC/DC Converters, Part 1	PDF \| HTML	2015年 9月 12日
	Application note	AN-2060 LM27402 Current Limit Application Circuits (Rev. A)		2013年 5月 6日
	Application note	Current Limit Foldback Improves Short Circuit Protection in LM274X Family (Rev. B)		2013年 4月 23日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

LM27402SQEVAL — LM27402 評估板

The LM27402 evaluation board represents a 20A typical application circuit. The application circuit is optimized for an input voltage of 12V. However, input voltage feed-forward technology allows the evaluation board to operate up to 20V while maintaining a stable output voltage of 1.5V at 20A. (...)

使用指南: PDF | HTML