LM317M
- Output Voltage Range Adjustable
from 1.25-V to 37-V - Output Current Greater Than 500-mA
- Internal Short-Circuit Current Limiting
- Thermal-Overload Protection
- Output Safe-Area Compensation
- Q Devices Meet Automotive Performance Requirements
- Customer-Specific Configuration Control Can Be Supported for Q Devices Along With
Major-Change Approval
The LM317M is an adjustable 3-terminal positive voltage regulator capable of supplying more than 500-mA over an output-voltage range of 1.25-V to
37-V. The LM317M is exceptionally easy to use and requires only two external resistors to set the output. Furthermore, both line and load regulation are better than standard fixed regulators.
In addition to having higher performance than fixed regulators, the LM317M includes on-chip current limiting, thermal-overload protection, and safe- operating-area protection. All overload protection remains fully functional if the ADJUST terminal is disconnected.
The LM317 is a floating regulator meaning there is no device ground terminal. Quiescent current flows to the load instead of being wasted flowing to ground. Regulated output voltage of hundreds of volts is possible if the maximum input to output differential does not exceed 40-V at any time. Device can be used as a floating current source controlled by a single resistor.
Normally, no capacitors are needed unless the device is more than six inches from the input filter capacitors, in which case an input bypass capacitor of any type is needed. An optional electrolytic or tantalum output capacitor can be added to improve transient response. Ceramic output capacitors can be used but output ringing may be present on transients. The ADJUST terminal can be bypassed with any type of capacitor to achieve high ripple-rejection ratios, which are difficult to achieve with standard three-terminal regulators.
技術文件
類型 | 標題 | 日期 | ||
---|---|---|---|---|
* | Data sheet | LM317M 3-Terminal Adjustable Regulator datasheet (Rev. P) | 2014年 3月 31日 | |
Application note | LDO Noise Demystified (Rev. B) | PDF | HTML | 2020年 8月 18日 | |
Application note | LDO PSRR Measurement Simplified (Rev. A) | PDF | HTML | 2017年 8月 9日 | |
Application note | Method For Cal Output Voltage Tolerances in Adj Regs (Rev. A) | 2013年 5月 5日 | ||
Application note | A New Production Technique for Trimming Voltage Regulators | 2002年 10月 3日 | ||
Application note | Adjustable 3-Terminal Regulator for Low-Cost Battery Charging Systems | 2002年 10月 3日 |
設計與開發
如需其他條款或必要資源,請按一下下方的任何標題以檢視詳細頁面 (如有)。
MLTLDO2EVM-037 — 適用於 DCY、DDA 和 KVU 封裝的通用 LDO 線性電壓穩壓器評估模組
MLTLDO2EVM-037 多重封裝低壓差 (LDO) 評估模組 (EVM) 可讓設計工程師評估多種常用線性穩壓器封裝的運作情形及性能,以利在自己的電路應用中使用。此 EVM 配置包含 DDA、3 針腳和 5 針腳 KVU,以及用於工程師焊接和評估其零件的 DCY 封裝板上配置。
封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
---|---|---|
SOT-223 (DCY) | 4 | Ultra Librarian |
TO-252 (KVU) | 3 | Ultra Librarian |
訂購與品質
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 認證摘要
- 進行中持續性的可靠性監測
- 晶圓廠位置
- 組裝地點
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。