LP87725-Q1
- AEC-Q100 qualified with the following results:
- Device temperature grade 1: –40°C to +125°C ambient operating temperature
- Functional safety-compliant device
- Developed for functional safety applications
- Documentation to aid ISO 26262 functional safety system design up to ASIL-B
- BUCK, LDO and load switch output and Input supply overvoltage and undervoltage monitoring
- Q&A Watchdog
- Level or PWM error signal monitor (ESM)
- ABIST and CRC
- Input voltage: 3.3 V nominal (3 V to 4 V range)
- 3 high-efficiency, low noise, high frequency step-down DC/DC converters:
- Output voltage: 0.8 V, 0.82 V, 0.9 V to 1.9 V with 20 mV output voltage step
- Maximum output current: 3.5 A
- Switching frequency: 4.4 MHz, 8.8 MHz, and 17.6 MHz
- 600 mA linear regulator with bypass \ load switch mode (LDO_LS1)
- Input voltage, LDO mode: 1.2 V to 4 V
- Output voltage: 0.6 V to 3.4 V with 50 mV output voltage step
- Input voltage, bypass \ load switch mode: 1.6 V to 3.4 V
- 400 mA load switch (LS2)
- Input voltage range: 1.6 V to 3.6 V
- On resistance 3.3-V input, 200 mA: 75 mΩ -typ
- Output short-circuit and overload protection
- Regulator output dynamic voltage scaling (DVS) through I2C interface
- Input overvoltage protection (OVP) and undervoltage lockout (UVLO)
- Two general purpose voltage monitors shared with LDO_LS1 and LS2 output
- Overtemperature warning and protection
- I2C interface supporting standard, fast mode, fast-mode+ and optional I2C address selection
The LP8772x-Q1 device is designed to meet the power management requirements of the AWR, IWR, and other MMICs in various automotive and industrial radar applications. The device has three step-down DC/DC converters, a LDO regulator, and a load switch. The LDO is powered externally and intended for supplying Ethernet device or any other device in the system. The load switch is intended to cut off the 3.3 V IO supply during the sensor sleep mode. The device is controlled by I2C communication interface and by enable signals.
The low noise step-down DC/DC converters support factory programmed switching frequency of 17.6 MHz or 8.8 MHz or 4.4 MHz. High switching frequency and low noise across wide frequency range, enables LDO-free power solution which helps to reduce the solution cost and improve thermal performance. The switching clock is forced to PWM mode for excellent RF performance and can also be synchronized to an external clock. The LP8772x-Q1 device supports remote voltage sensing to compensate IR drop between the regulator output and the point-of-load (POL) which improves the accuracy of the output voltage.
The LP8772x-Q1 device supports programmable start-up and shutdown delays and sequences which are synchronized to the ENABLE signal. These sequences can also include GPO signal to control external regulators, load switches, and processor reset. The default settings for the device are programmed into nonvolatile memory (NVM) / one time programmable (OTP) memory at the factory and user cannot change the device default NVM / OTP settings. The device controls the output slew rate to minimize output voltage overshoot and in-rush current during device start-up.
索取更多資訊
提供完整的產品規格表和其他資訊。立即索取
技術文件
| 類型 | 標題 | 日期 | ||
|---|---|---|---|---|
| * | Data sheet | LP8772x-Q1 Three Buck Converters, One Linear Regulator and One Load Switch for mmWave Radar Sensors datasheet | PDF | HTML | 2023年 12月 18日 |
設計與開發
電源供應解決方案
探索包括 LP87725-Q1 的解決方案。TI 提供適用於 TI 與非 TI 之系統單晶片 (SoC)、處理器、微控制器、感測器或現場可編程邏輯閘陣列 (FPGA) 的電源供應解決方案。
AWR2544LOPEVM — 適用於車用第二代、76GHz 至 81GHz、高效能 SoC 的 AWR2544LOP 評估模組
LP87725Q1EVM — LP87725-Q1 評估模組
PEET-GUI — PMIC 效率評估器工具 (PEET)
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| VQFN-HR (RAG) | 24 | Ultra Librarian |
訂購與品質
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 認證摘要
- 進行中持續性的可靠性監測
- 晶圓廠位置
- 組裝地點
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。