首頁 微控制器 (MCU) 與處理器 Microcontrollers Low-power MCUs
首頁
微控制器 (MCU) 與處理器
Microcontrollers
Low-power MCUs

MSP430F5438A-ET

現行

具有 256-KB 快閃記憶體、16-KB SRAM、12 位元 ADC、DMA、UART/SPI/I2C、計時器的廣泛溫度 25-MHz MCU

立即訂購
產品規格表

MSP430F5438A-ET

現行
產品規格表 立即訂購

產品詳細資料

Frequency (MHz) 25 RAM (kByte) 16 ADC type 12-bit SAR Features Real-time clock UART 4 SPI 8 Hardware accelerators 0 Operating temperature range (°C) -55 to 125 Rating HiRel Enhanced Product Operating system BareMetal (No OS), TI RTOS Nonvolatile memory (kByte) 256 Number of I2Cs 4 Security Secure debug
Frequency (MHz) 25 RAM (kByte) 16 ADC type 12-bit SAR Features Real-time clock UART 4 SPI 8 Hardware accelerators 0 Operating temperature range (°C) -55 to 125 Rating HiRel Enhanced Product Operating system BareMetal (No OS), TI RTOS Nonvolatile memory (kByte) 256 Number of I2Cs 4 Security Secure debug
NFBGA (GCA) 113 49 mm² 7 x 7 NFBGA (ZCA) 113 49 mm² 7 x 7
  • Extended temperature version -ET uses silicon revision H
  • Low supply voltage range: 3.6 V down to 1.8 V
  • Ultralow power consumption
    • Active mode (AM): all system clocks active 230 µA/MHz at 8 MHz, 3.0 V, flash program execution (typical) 110 µA/MHz at 8 MHz, 3.0 V, RAM program execution (typical)
    • Standby mode (LPM3): real-time clock with crystal, watchdog, and supply supervisor operational, full RAM retention, fast wake-up: 1.7 µA at 2.2 V, 2.1 µA at 3.0 V (typical) low-power oscillator (VLO), general-purpose counter, watchdog, and supply supervisor operational, full RAM retention, fast wake-up: 1.2 µA at 3.0 V (typical)
    • Off mode (LPM4): full RAM retention, supply supervisor operational, fast wake-up: 1.2 µA at 3.0 V (typical)
    • Shutdown mode (LPM4.5): 0.1 µA at 3.0 V (typical)
  • Wake-up from standby mode in 3.5 µs (typical)
  • 16-bit RISC architecture
    • Extended memory
    • Up to 25-MHz system clock
  • Flexible power management system
    • Fully integrated LDO with programmable regulated core supply voltage
    • Supply voltage supervision, monitoring, and brownout
  • Unified clock system
    • FLL control loop for frequency stabilization
    • Low-power low-frequency internal clock source (VLO)
    • Low-frequency trimmed internal reference source (REFO)
    • 32-kHz crystals
    • High-frequency crystals up to 32 MHz (1)
  • 16-bit timer TA0, Timer_A with five capture/compare registers
  • 16-bit timer TA1, Timer_A with three capture/compare registers
  • 16-bit timer TB0, Timer_B with seven capture/compare shadow registers
  • Up to four universal serial communication interfaces
    • USCI_A0, USCI_A1, USCI_A2, and USCI_A3 each supporting
      • Enhanced UART supporting automatic baud-rate detection
      • IrDA encoder and decoder
      • Synchronous SPI
    • USCI_B0, USCI_B1, USCI_B2, and USCI_B3 each supporting
      • I2C
      • Synchronous SPI
  • 12-bit analog-to-digital converter (ADC)
    • Internal reference
    • Sample-and-hold
    • Autoscan feature
    • 14 external channels, 2 internal channels
  • Hardware multiplier supporting 32-bit operations
  • Serial onboard programming, no external programming voltage needed
  • 3-channel internal DMA
  • Basic timer with real-time clock feature
  • Wide operational range: –40°C to 125°C (Q temp), –55°C to 125°C (M temp) (some noted parameters specified for –40°C to 85°C only)
  • Available SnAgCu (ZCA) or SnPb (GCA) ball material

(1)Use of crystals is not ensured above 85°C for both 32-kHz and high-frequency crystals.
  • Extended temperature version -ET uses silicon revision H
  • Low supply voltage range: 3.6 V down to 1.8 V
  • Ultralow power consumption
    • Active mode (AM): all system clocks active 230 µA/MHz at 8 MHz, 3.0 V, flash program execution (typical) 110 µA/MHz at 8 MHz, 3.0 V, RAM program execution (typical)
    • Standby mode (LPM3): real-time clock with crystal, watchdog, and supply supervisor operational, full RAM retention, fast wake-up: 1.7 µA at 2.2 V, 2.1 µA at 3.0 V (typical) low-power oscillator (VLO), general-purpose counter, watchdog, and supply supervisor operational, full RAM retention, fast wake-up: 1.2 µA at 3.0 V (typical)
    • Off mode (LPM4): full RAM retention, supply supervisor operational, fast wake-up: 1.2 µA at 3.0 V (typical)
    • Shutdown mode (LPM4.5): 0.1 µA at 3.0 V (typical)
  • Wake-up from standby mode in 3.5 µs (typical)
  • 16-bit RISC architecture
    • Extended memory
    • Up to 25-MHz system clock
  • Flexible power management system
    • Fully integrated LDO with programmable regulated core supply voltage
    • Supply voltage supervision, monitoring, and brownout
  • Unified clock system
    • FLL control loop for frequency stabilization
    • Low-power low-frequency internal clock source (VLO)
    • Low-frequency trimmed internal reference source (REFO)
    • 32-kHz crystals
    • High-frequency crystals up to 32 MHz (1)
  • 16-bit timer TA0, Timer_A with five capture/compare registers
  • 16-bit timer TA1, Timer_A with three capture/compare registers
  • 16-bit timer TB0, Timer_B with seven capture/compare shadow registers
  • Up to four universal serial communication interfaces
    • USCI_A0, USCI_A1, USCI_A2, and USCI_A3 each supporting
      • Enhanced UART supporting automatic baud-rate detection
      • IrDA encoder and decoder
      • Synchronous SPI
    • USCI_B0, USCI_B1, USCI_B2, and USCI_B3 each supporting
      • I2C
      • Synchronous SPI
  • 12-bit analog-to-digital converter (ADC)
    • Internal reference
    • Sample-and-hold
    • Autoscan feature
    • 14 external channels, 2 internal channels
  • Hardware multiplier supporting 32-bit operations
  • Serial onboard programming, no external programming voltage needed
  • 3-channel internal DMA
  • Basic timer with real-time clock feature
  • Wide operational range: –40°C to 125°C (Q temp), –55°C to 125°C (M temp) (some noted parameters specified for –40°C to 85°C only)
  • Available SnAgCu (ZCA) or SnPb (GCA) ball material

(1)Use of crystals is not ensured above 85°C for both 32-kHz and high-frequency crystals.

The MSP430F5438A-ET is an ultralow-power microcontroller. The architecture, combined with extensive low-power modes, is optimized to achieve extended battery life in portable measurement applications. The device features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows wake-up from low-power modes to active mode in 3.5 µs (typical).

The MSP430F5438A-ET is a microcontroller configuration with three 16-bit timers, a high-performance 12-bit analog-to-digital converter (ADC), up to 4 universal serial communication interfaces (USCIs), a hardware multiplier, a DMA, a real-time clock (RTC) module with alarm capabilities, and up to 87 I/O pins. For complete module descriptions, see the MSP430F5xx and MSP430F6xx Family User’s Guide .

Typical applications for this device include analog and digital sensor systems, digital motor control, remote controls, thermostats, digital timers, and hand-held meters.

The MSP430F5438A-ET is an ultralow-power microcontroller. The architecture, combined with extensive low-power modes, is optimized to achieve extended battery life in portable measurement applications. The device features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows wake-up from low-power modes to active mode in 3.5 µs (typical).

The MSP430F5438A-ET is a microcontroller configuration with three 16-bit timers, a high-performance 12-bit analog-to-digital converter (ADC), up to 4 universal serial communication interfaces (USCIs), a hardware multiplier, a DMA, a real-time clock (RTC) module with alarm capabilities, and up to 87 I/O pins. For complete module descriptions, see the MSP430F5xx and MSP430F6xx Family User’s Guide .

Typical applications for this device include analog and digital sensor systems, digital motor control, remote controls, thermostats, digital timers, and hand-held meters.
filter 尋找其它 Low-power MCUs
下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
引腳對引腳且具備與所比較裝置相同的功能
MSP430F5438A 現行 具 256 KB 快閃記憶體、16-KB SRAM、12 位元 ADC、DMA、UART/SPI/I2C、定時器、HW 倍頻器的 25 MHz MCU Industrial temperature option is available.

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 4
重要文件 類型 標題 格式選項 日期
* Data sheet MSP430F5438A-ET Mixed-Signal Controller datasheet (Rev. A) PDF | HTML 2021年 2月 25日
Application note Migration Guide From MSP430 MCUs to MSPM0 MCUs (Rev. B) PDF | HTML 2025年 6月 2日
User guide MSP430 MCUs Development Guide Book (Rev. A) PDF | HTML 2021年 5月 13日
Application note MSP430 System ESD Troubleshooting Guide PDF | HTML 2019年 12月 13日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

ALGO-3P-UISP1-TI — 適用於德州儀器裝置的 Algocraft μISP1 編程器

μISP 可以連接到主機 PC (內建 RS-232、USB、LAN 連接) 或獨立模式工作。

在單機模式下，只要按下「開始」按鈕或透過一些 TTL 控制線，就可以執行編程週期。

其緊湊的尺寸和多功能性可輕鬆整合到生產環境、手動和自動化程序中。

從：Algocraft
造訪合作夥伴網站
硬體程式設計工具

MSP-FET — MSP MCU 程式設計工具和偵錯器

MSP-FET 是一款強大的模擬開發工具，通常稱為偵錯探測器，可讓使用者快速展開 MSP 低功耗微控制器 (MCU) 的開始工作。

它支援透過 JTAG 和 SBW 介面進行編程和即時偵錯。此外，MSP-FET 也能在電腦 USB 介面與 MSP UART 間提供後通道 UART 連接。這為 MSP 程式設計工具提供了一種便利的方法，能在 MSP 和電腦上執行的終端之間進行串行通訊。它也支援透過 UART 和 I2C 通訊協定，使用 BSL（自舉式載入程式）將程式（通常稱為韌體）載入到 MSP 目標。

USB 介面可將 MSP-FET 連接至電腦，而 14 針腳連接器則可存取 MSP (...)

使用指南: PDF | HTML
TI.com 無法提供
硬體程式設計工具

ALGO-3P-WRITENOW — Algocraft WriteNow！程式設計工具

WriteNow! 系統內編程器系列是可編程產業的一大突破。此編程器支援多家製造商的眾多裝置 (例如微控制器、記憶體、CPLD 與其他可編程裝置)。其尺寸精巧，便於整合至 ATE 與固定裝置。編程器可單機運作，或透過內建的 RS-232、LAN 與 USB 連接埠與主機電腦連線，並隨附操作簡易的工具軟體。

從：Algocraft
造訪合作夥伴網站
軟體開發套件 (SDK)

MSP430-SDK — MSPWare for MSP430 Microcontrollers

MSP430-SDK is a collection of resources that help users to write effective code for MSP430 microcontrollers (MCUs). These resources support ALL MSP430 microcontrollers. As one user mentioned, “It’s essentially everything developers need to become MSP430 microcontroller experts!”

This collection of (...)

支援產品和硬體

支援產品和硬體
瀏覽 下載選項
驅動程式或資料庫

MSP-DSPLIB — Digital Signal Processing (DSP) Library for MSP Microcontrollers

The TI MSP430™ Digital Signal Processing library is a set of optimized functions to perform common signal processing operations for MSP430 microcontrollers. These functions are used in applications where processing-intensive transforms are done in real-time for minimal energy and with very (...)

支援產品和硬體

支援產品和硬體
瀏覽 下載選項
快速入門

TI-DEVELOPER-ZONE — Start embedded development on your desktop or in the cloud

From evaluation to deployment the TI Developer Zone provides a comprehensive range of software, tools and training to ensure that you have everything you need for each stage of the development process.
支援產品和硬體

支援產品和硬體
開始使用
IDE、配置、編譯器或偵錯程式

CCSTUDIO — Code Composer Studio™ integrated development environment (IDE)

CCStudio™ IDE is part of TI's extensive CCStudio™ development tool ecosystem. It is an integrated development environment (IDE) for TI's microcontrollers, processors, wireless connectivity devices and radar sensors. It is comprised of a rich suite of tools used to build, debug, analyze and optimize (...)

支援產品和硬體

支援產品和硬體
啟動 下載選項
IDE、配置、編譯器或偵錯程式

IAR-KICKSTART — IAR Embedded Workbench

IAR Embedded Workbench delivers a complete development toolchain for building and debugging embedded applications for your selected target microcontroller. The included IAR C/C++ Compiler generates highly optimized code for your application, and the C-SPY Debugger is a fully integrated debugger for (...)
從：IAR Systems
使用指南: PDF
View Options
線上培訓

MSP430-ACADEMY — MSP430™ academy

MSP430™ academy delivers easy-to-use training modules that span a wide range of topics and LaunchPads in the MSP430 MCU portfolio.
支援產品和硬體

支援產品和硬體
瀏覽
作業系統 (OS)

WHIS-3P-SAFERTOS — WITTENSTEIN SAFERTOS 預先認證的安全 RTOS

SAFERTOS® 是專為嵌入式處理器設計的獨特即時作業系統。經 TÜV SÜD 預先認證，符合 IEC 61508 SIL3 與 ISO 26262 ASILD 標準。SAFERTOS® 是由 WHIS 專家團隊專為安全而打造，適用於全球重要安全應用。WHIS 與德州儀器的合作已經超過十年。在此期間，WHIS 已將 SAFERTOS® 移植至各種 TI 處理器，支援所有熱門核心，並可依要求提供其他架構。SAFERTOS® 專為您的特定處理器/編譯器組合量身打造，隨附完整的原始程式碼與設計保證包，可完全一目了然整個設計生命週期。許多 WHIS 客戶開始使用 FreeRTOS (...)
從：WITTENSTEIN High Integrity Systems
造訪合作夥伴網站
軟體程式設計工具

MSP-GANG-SOFTWARE — MSP-GANG Software

The MSP Gang Programmer (MSP-GANG) is a MSPM0/MSP430/MSP432 device programmer that can program up to eight identical devices at the same time.
支援產品和硬體

支援產品和硬體
下載選項
軟體程式設計工具

UNIFLASH — UniFlash for most TI microcontrollers (MCUs) and mmWave sensors

UniFlash is a software tool for programming on-chip flash on TI microcontrollers and wireless connectivity devices and on-board flash for TI processors. UniFlash provides both graphical and command-line interfaces.

UniFlash can be run from the cloud on the TI Developer Zone or downloaded and used (...)

支援產品和硬體

支援產品和硬體
啟動 下載選項
設計工具

MSP-3P-SEARCH — MSP 第三方搜尋工具

TI has partnered with multiple companies to offer a wide range of solutions and services for TI MSP devices. These companies can accelerate your path to production using MSP devices. Download this search tool to quickly browse third-party details and find the right third-party to meet your needs.

(...)

下載
封裝 針腳 CAD 符號、佔位空間與 3D 模型
NFBGA (GCA) 113 Ultra Librarian
NFBGA (ZCA) 113 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片