設計工具
TLV6001
- Precision Amplifiers for Cost-Sensitive Systems
- Low Quiescent Current: 75 µA/ch
- Supply Range: 1.8 V to 5.5 V
- Input Voltage Noise Density: 28 nV/√Hz at 1 kHz
- Rail-to-Rail Input and Output
- Gain Bandwidth: 1 MHz
- Low Input Bias Current: 1 pA
- Low Offset Voltage: 0.75 mV
- Unity-Gain Stable
- Internal RF and EMI Filter
- Extended Temperature Range:
–40°C to +125°C
The TLV600x family of single-, dual-, and quad-channel operational amplifiers is specifically designed for general-purpose applications. Featuring rail-to-rail input and output (RRIO) swings, low quiescent current (75 µA, typical), wide bandwidth (1 MHz) and low noise (28 nV/√Hz at 1 kHz), this family is attractive for a variety of applications that require a good balance between cost and performance, such as consumer electronics, smoke detectors, and white goods. The low-input-bias current (±1.0 pA, typical) enables the TLV600x to be used in applications with megaohm source impedances.
The robust design of the TLV600x provides ease-of-use to the circuit designer: unity-gain stability with capacitive loads of up to 150 pF, integrated RF/EMI rejection filter, no phase reversal in overdrive conditions, and high electrostatic discharge (ESD) protection (4-kV HBM).
The devices are optimized for operation at voltages as low as 1.8 V (±0.9 V) and up to 5.5 V (±2.75 V), and are specified over the extended temperature range of –40°C to +125°C.
The single-channel TLV6001 is available in SC70-5 and SOT23-5 packages. The dual-channel TLV6002 is offered in SOIC-8 and VSSOP-8 packages, and the quad-channel TLV6004 is offered in a TSSOP-14 package.
技術文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 7 | 類型 | 標題 | 日期 | ||
|---|---|---|---|---|
| * | Data sheet | TLV600x Low-Power, Rail-to-Rail In/Out, 1-MHz Operational Amplifier for Cost-Sensitive Systems datasheet (Rev. D) | PDF | HTML | 2017年 5月 29日 |
| Application brief | Interfacing a Differential-Output (Isolated) Amp to a Single-Ended Input ADC (Rev. B) | PDF | HTML | 2023年 6月 2日 | |
| E-book | An Engineer’s Guide to Designing with Precision Amplifiers | 2021年 4月 29日 | ||
| Circuit design | Difference amplifier (subtractor) circuit (Rev. A) | PDF | HTML | 2019年 1月 31日 | |
| EVM User's guide | AMC1311EVM User's Guide | 2017年 11月 13日 | ||
| Technical article | Transimpedance amplifier designs for high-performance, cost-sensitive smoke detect | PDF | HTML | 2017年 8月 10日 | |
| E-book | The Signal e-book: A compendium of blog posts on op amp design topics | 2017年 3月 28日 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
開發板
AMC1311EVM — AMC1311 評估模組
The AMC1311 device is a high-voltage isolation amplifier with a differential output separated from the input interface circuitry by a silicon dioxide (SiO2) isolation barrier. The isolation barrier provides galvanic isolation of up to 7000 VPEAK. When used in combination with TLV6001, the (...)
使用指南: PDF
開發板
AMP-PDK-EVM — 放大器性能開發套件評估模組
放大器性能開發套件 (PDK) 是一款評估模組 (EVM) 套件，可測試通用運算放大器 (op amp) 參數，並與大多數運算放大器和比較器相容。EVM 套件提供主板和多個插槽式子卡選項，可滿足封裝需求，使工程師能夠快速評估和驗證裝置性能。
AMP-PDK-EVM 套件支援五種最熱門的業界標準封裝，包括：
- D (SOIC-8 和 SOIC-14)
- PW (TSSOP-14)
- DGK (VSSOP-8)
- DBV (SOT23-5 和 SOT23-6)
- DCK (SC70-5 和 SC70-6)
開發板
DIP-ADAPTER-EVM — DIP 轉接器評估模組
Speed up your op amp prototyping and testing with the DIP-Adapter-EVM, which provides a fast, easy and inexpensive way to interface with small, surface-mount ICs. You can connect any supported op amp using the included Samtec terminal strips or wire them directly to existing circuits.
The (...)
使用指南: PDF
開發板
DIYAMP-EVM — 通用自製 (DIY) 放大器電路評估模組
The DIYAMP-EVM is a unique evaluation module (EVM) family that provides engineers and do it yourselfers (DIYers) with real-world amplifier circuits, enabling you to quickly evaluate design concepts and verify simulations. It is available in three industry-standard packages (SC70, SOT23, SOIC) and (...)
開發板
ISO224EVM — ISO224 評估模組
The ISO224 evaluation module (EVM) is an evaluation platform for ISO224, which is a 7-kV reinforced isolation amplifier designed for use in voltage-measuring applications. ISO224EVM allows the user to explore all the features of the ISO224 device. ISO224EVM also features a bipolar (...)
使用指南: PDF
計算工具
ANALOG-ENGINEER-CALC — 類比工程師計算機
The Analog Engineer’s Calculator is designed to speed up many of the repetitive calculations that analog circuit design engineers use on a regular basis. This PC-based tool provides a graphical interface with a list of various common calculations ranging from setting op-amp gain with feedback (...)
設計工具
CIRCUIT060013 — 具有 T 網路回饋電路的反相放大器
此設計可反轉輸入訊號 VIN，並使用 1000 V/V 或 60 dB 訊號增益。具有 T 回饋網路的反相放大器可在沒有較小 R4 值或超大回饋電阻器值的情況下獲得高增益。
設計工具
CIRCUIT060024 — 差分放大器 (減法器) 電路
This design inputs two signals, Vi1 and Vi2, and outputs their difference (subtracts). The input signals typically come from low-impedance sources because the input impedance of this circuit is determined by the resistive network. Difference amplifiers are typically used to amplify differential (...)
設計工具
CIRCUIT060074 — 具有比較器電路的高壓側電流感測
此高壓側電流感測解決方案使用一個具有軌對軌輸入共模範圍的比較器，若負載電流上升到 1 A 以上，便在比較器輸出 (COMP OUT) 建立過電流警示 (OC 警示) 訊號。此實作中的 OC 訊號為低電位作動。因此當超過 1-A 閾值時，比較器輸出會變低。實作磁滯後會在負載電流降低至 0.5 A (減少 50%) 時，讓 OC-Alert 返回邏輯高狀態。此電路利用開漏輸出比較器，為控制數位邏輯輸入針腳而進行電平轉換輸出高邏輯電平。對於需要驅動 MOSFET 開關閘極的應用，建議使用具推挽輸出的比較器。
模擬工具
PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具
PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
模擬工具
TINA-TI — 基於 SPICE 的類比模擬程式
TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
使用指南: PDF
參考設計
TIDA-00420 — ADC 架構、數位隔離、廣泛輸入、16 通道、AC/DC 二進位輸入參考設計
此參考設計展現具強化型隔離的成本最佳化、可擴充 ADC 架構 AC/DC 二進位輸入模組 (BIM) 架構。10 位元或 12 位元 SAR ADC 的 16 通道，用於感測多個二進位輸入。運算放大器除了維持低每頻道成本外，也可為各輸入提供最佳訊號調節。數位隔離器 (基本型或強化型) 可用於隔離主機 MCU 或處理器。提供可測量溫度，濕度和磁場以進行診斷的設備。具可配置輸出的強化型隔離 DC/DC 電源供應器，可提供二進位模組所需的電源。
參考設計
TIDA-010065 — 基於高效、低排放、隔離式 DC/DC 轉換器的類比輸入模組參考設計
此參考設計為一簡化架構，可產生隔離式電源供應，適用於測量隔離電壓與電流的隔離式放大器。具 5-V 輸入之強化隔離操作的完全整合式 DC/DC 轉換器，並具備可設定 5-V 或 5.4-V 輸出 (適用於低壓降穩壓器 (LDO) 的空餘空間) 可產生隔離電源。介接至 ±50-mV 輸入範圍隔離放大器，且配置爲通道隔離輸入的分流，可測量電流。連接至 ±250-mV 或 ±12-V 輸入範圍隔離放大器，且配置爲群組隔離輸入的潛在分頻器，可測量電壓。隔離放大器介面直接輸出至 24 位元 ΔΣ 類比轉數位轉換器 (ADC)，或使用增益放大器擴展至 ±10 V，並連接至 16 位元 SAR ADC (...)
參考設計
TIDA-010232 — 隔離監控採用高電壓 EV 充電和太陽能的 AFE 參考設計
此參考設計採用電橋 DC 絕緣監控 (DC-IM)方法，其允許精確對稱和不對稱絕緣洩漏偵測機制和隔離電阻偵測機制。我們為您介紹新一代隔離式放大器與交換器，其在熱側無需外部電源供應器就能啟用隔離。因此，MCU 可以從冷端供電隔離裝置。絕緣監控診斷可直接透過電源轉換或充電協定 MCU 進行處理。
Design guide: PDF
參考設計
TIDA-00778 — 單分流、雙分流、三分流 FOC，電流感測小於 1-us 的三相逆變器參考設計
The TIDA-00778 reference design demonstrates fast and accurate current sensing for a three-phase motor driven with sensorless field-oriented control (FOC). Drives with lower audible noise require faster andaccurate current sensing. The most common low-cost current-sensing methods use a single (...)
參考設計
TIDA-01456 — 適用於 200-480V AC 工業驅動器的精巧型非隔離式三相逆變器參考設計
This reference design realizes a 3 phase inverter subsystem for variable frequency AC inverter drives and servo drives. This design is particularly suited for drive architectures in which the microcontroller and inverter ground are non-isolated. The basic isolated gate driver UCC5320S is used for (...)
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| SOT-23 (DBV) | 5 | Ultra Librarian |
| SOT-SC70 (DCK) | 5 | Ultra Librarian |
訂購與品質
內含資訊：
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 認證摘要
- 進行中持續性的可靠性監測
內含資訊：
- 晶圓廠位置
- 組裝地點