TPS53819A

現行

具 PMBus 的 3-V 至 28-V,40-A 同步 D-CAP2 降壓控制器

產品詳細資料

Vin (min) (V) 3 Vin (max) (V) 28 Iout (max) (A) 40 Operating temperature range (°C) -40 to 85 Control mode D-CAP2 Topology Buck Rating Catalog Vout (min) (V) 0.6 Vout (max) (V) 5.5 Features Adjustable current limit, Dynamic Voltage Scaling, Enable, Light Load Efficiency, PMBus, Power good, Pre-Bias Start-Up, Synchronous Rectification Iq (typ) (µA) 920 Duty cycle (max) (%) 90 Number of phases 1
Vin (min) (V) 3 Vin (max) (V) 28 Iout (max) (A) 40 Operating temperature range (°C) -40 to 85 Control mode D-CAP2 Topology Buck Rating Catalog Vout (min) (V) 0.6 Vout (max) (V) 5.5 Features Adjustable current limit, Dynamic Voltage Scaling, Enable, Light Load Efficiency, PMBus, Power good, Pre-Bias Start-Up, Synchronous Rectification Iq (typ) (µA) 920 Duty cycle (max) (%) 90 Number of phases 1
VQFN (RGT) 16 9 mm² 3 x 3
  • Conversion Input Voltage 3 V to 28 V
  • VDD input voltage 4.5 V to 28 V
  • Output voltage 0.6 V to 5.5 V
  • Supports all ceramic output capacitors
  • Reference voltage: 600 mV ±0.5% tolerance
  • ±9% Voltage adjustment with PMBus™
  • Built-in 5-V LDO
  • D-CAP2™ mode with 100-ns load-step response
  • Auto-skip Eco-mode™ for light-load efficiency
  • Adaptive on-time control architecture with eight selectable frequencies using PMBus
  • Supports voltage margining using PMBus
  • Programmable soft-start time using PMBus
  • Programmable power-on delay using PMBus
  • Programmable VDD UVLO level using PMBus
  • Fault report using PMBus
  • Pre-charged start-up capability
  • Built-In output discharge
  • Power-good output with programmable delay
  • Internal overvoltage, undervoltage, and overcurrent limit protections
  • Thermal shutdown (non-latch)
  • 3 mm × 3 mm, 16-pin, QFN package
  • Create a custom design using the TPS53819A with the WEBENCH® Power Designer
  • Conversion Input Voltage 3 V to 28 V
  • VDD input voltage 4.5 V to 28 V
  • Output voltage 0.6 V to 5.5 V
  • Supports all ceramic output capacitors
  • Reference voltage: 600 mV ±0.5% tolerance
  • ±9% Voltage adjustment with PMBus™
  • Built-in 5-V LDO
  • D-CAP2™ mode with 100-ns load-step response
  • Auto-skip Eco-mode™ for light-load efficiency
  • Adaptive on-time control architecture with eight selectable frequencies using PMBus
  • Supports voltage margining using PMBus
  • Programmable soft-start time using PMBus
  • Programmable power-on delay using PMBus
  • Programmable VDD UVLO level using PMBus
  • Fault report using PMBus
  • Pre-charged start-up capability
  • Built-In output discharge
  • Power-good output with programmable delay
  • Internal overvoltage, undervoltage, and overcurrent limit protections
  • Thermal shutdown (non-latch)
  • 3 mm × 3 mm, 16-pin, QFN package
  • Create a custom design using the TPS53819A with the WEBENCH® Power Designer

The TPS53819A device is a small-sized, single buck controller with adaptive on-time D-CAP2 mode control and PMBus. The device is suitable for low output voltage and high current, system power rail, or similar point-of-load (POL) power supply in digital consumer products. Small package with minimal pin-count saves space on the PCB, while the programmability and fault report via PMBus simplify the power supply design. The skip-mode at light-load condition combined with strong gate drivers and low-side FET on-resistance (RDS(on)) current sensing can support low-loss and high efficiency operation, over a broad load range. The conversion input voltage, which is the high-side FET drain voltage, ranges from 3 V to 28 V. The supply voltage (VDD) is from 4.5 V to 28 V. The output voltage ranges from 0.6 V to 5.5 V. The device is available in a 16-pin, QFN package and is specified from –40°C to +85°C.

The TPS53819A device is a small-sized, single buck controller with adaptive on-time D-CAP2 mode control and PMBus. The device is suitable for low output voltage and high current, system power rail, or similar point-of-load (POL) power supply in digital consumer products. Small package with minimal pin-count saves space on the PCB, while the programmability and fault report via PMBus simplify the power supply design. The skip-mode at light-load condition combined with strong gate drivers and low-side FET on-resistance (RDS(on)) current sensing can support low-loss and high efficiency operation, over a broad load range. The conversion input voltage, which is the high-side FET drain voltage, ranges from 3 V to 28 V. The supply voltage (VDD) is from 4.5 V to 28 V. The output voltage ranges from 0.6 V to 5.5 V. The device is available in a 16-pin, QFN package and is specified from –40°C to +85°C.

下載 觀看有字幕稿的影片 影片

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件,然後再試一次。
檢視所有 5
類型 標題 日期
* Data sheet TPS53819A 3-V to 28-V Input, 40-A, Eco-Mode™, D-CAP2™ Synchronous Buck Controller With PMBus™ datasheet (Rev. B) PDF | HTML 2019年 4月 5日
User guide TPS53819A Buck Controller Evaluation Module User's Guide (Rev. B) PDF | HTML 2021年 11月 8日
Application note Programming the TPS53819A 3-V to 28-V Input, 40-A, Eco-mode™, D-CAP2™ 2020年 5月 5日
White paper Power solution options for data center applications (Rev. A) 2020年 2月 27日
Technical article Select the correct PMBus POL solution for your application PDF | HTML 2015年 8月 3日

設計與開發

如需其他條款或必要資源,請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TPS53819AEVM-123 — TPS53819A 評估模組

The Texas Instruments TPS53819AEVM-123 evaluation module (EVM) helps designers evaluate the performance of the TPS53819A High Performance, Single Synchronous Step-Down Controller with PMBus. If a designer wants to communicate with this EVM from a Windows-based PC, a separate USB Interface Adapter (...)
使用指南: PDF | HTML
TI.com 無法提供
模擬型號

TPS53819A TINA-TI Reference Design

SLUM546.TSC (867 KB) - TINA-TI Reference Design
模擬型號

TPS53819A TINA-TI Transient Spice Model

SLUM545.ZIP (76 KB) - TINA-TI Spice Model
模擬型號

TPS53819A Unencrypted PSpice Transient Model Package (Rev. A)

SLUM349A.ZIP (40 KB) - PSpice Model
封裝 針腳 CAD 符號、佔位空間與 3D 模型
VQFN (RGT) 16 Ultra Librarian

訂購與品質

內含資訊:
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊:
  • 晶圓廠位置
  • 組裝地點

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

內容係由 TI 和社群貢獻者依「現狀」提供,且不構成 TI 規範。檢視使用條款

若有關於品質、封裝或訂購 TI 產品的問題,請參閱 TI 支援。​​​​​​​​​​​​​​

影片