首頁 電源管理 AC/DC 和 DC/DC 轉換器 (整合式 FET)
首頁
電源管理
AC/DC 和 DC/DC 轉換器 (整合式 FET)

TPS61090

現行

1.8Vin、2A 開關、96% 高效升壓轉換器

立即訂購
產品規格表

TPS61090

現行
產品規格表 立即訂購

產品詳細資料

Rating Catalog Operating temperature range (°C) -40 to 125 Topology Boost Type Converter Vin (min) (V) 1.8 Vin (max) (V) 5.5 Switching frequency (min) (kHz) 500 Switching frequency (max) (kHz) 700 Features Synchronous Rectification Vout (min) (V) 1.8 Vout (max) (V) 5.5 Iq (typ) (µA) 20 Duty cycle (max) (%) 100 Switch current limit (typ) (A) 2
Rating Catalog Operating temperature range (°C) -40 to 125 Topology Boost Type Converter Vin (min) (V) 1.8 Vin (max) (V) 5.5 Switching frequency (min) (kHz) 500 Switching frequency (max) (kHz) 700 Features Synchronous Rectification Vout (min) (V) 1.8 Vout (max) (V) 5.5 Iq (typ) (µA) 20 Duty cycle (max) (%) 100 Switch current limit (typ) (A) 2
VQFN (RSA) 16 16 mm² 4 x 4
  • Synchronous (96% Efficient) Boost Converter
    With 500-mA Output Current From 1.8-V Input
  • Available in a 16-Pin VQFN 4 × 4 Package
  • Device Quiescent Current: 20 µA (Typ)
  • Input Voltage Range: 1.8 V to 5.5 V
  • Adjustable Output Voltage Up to 5.5 V Fixed Output
    Voltage Options
  • Power Save Mode for Improved Efficiency at Low
    Output Power
  • Low Battery Comparator
  • Low EMI-Converter (Integrated Antiringing Switch)
  • Load Disconnect During Shutdown
  • Over-Temperature Protection
  • Synchronous (96% Efficient) Boost Converter
    With 500-mA Output Current From 1.8-V Input
  • Available in a 16-Pin VQFN 4 × 4 Package
  • Device Quiescent Current: 20 µA (Typ)
  • Input Voltage Range: 1.8 V to 5.5 V
  • Adjustable Output Voltage Up to 5.5 V Fixed Output
    Voltage Options
  • Power Save Mode for Improved Efficiency at Low
    Output Power
  • Low Battery Comparator
  • Low EMI-Converter (Integrated Antiringing Switch)
  • Load Disconnect During Shutdown
  • Over-Temperature Protection

The TPS6109x devices provide a power supply solution for products powered by either a one-cell Li-Ion or Li-Polymer, or a two-cell alkaline, NiCd or NiMH battery and required supply currents up to or higher than 1 A. The converter generates a stable output voltage that is either adjusted by an external resistor divider or fixed internally on the chip. It provides high efficient power conversion and is capable of delivering output currents up to 0.5 A at 5 V at a supply voltage down to 1.8 V. The implemented boost converter is based on a fixed frequency, pulse-width- modulation (PWM) controller using a synchronous rectifier to obtain maximum efficiency. Boost switch and rectifier switch are connected internally to provide the lowest leakage inductance and best EMI behavior possible. The maximum peak current in the boost switch is limited to a value of 2500 mA.

The converter can be disabled to minimize battery drain. During shutdown, the load is completely disconnected from the battery. A low-EMI mode is implemented to reduce ringing and, in effect, lower radiated electromagnetic energy when the converter enters the discontinuous conduction mode.

The output voltage can be programmed by an external resistor divider or is fixed internally on the chip.

The device is packaged in a 16-pin VQFN 4-mm × 4-mm (16 RSA) package.

The TPS6109x devices provide a power supply solution for products powered by either a one-cell Li-Ion or Li-Polymer, or a two-cell alkaline, NiCd or NiMH battery and required supply currents up to or higher than 1 A. The converter generates a stable output voltage that is either adjusted by an external resistor divider or fixed internally on the chip. It provides high efficient power conversion and is capable of delivering output currents up to 0.5 A at 5 V at a supply voltage down to 1.8 V. The implemented boost converter is based on a fixed frequency, pulse-width- modulation (PWM) controller using a synchronous rectifier to obtain maximum efficiency. Boost switch and rectifier switch are connected internally to provide the lowest leakage inductance and best EMI behavior possible. The maximum peak current in the boost switch is limited to a value of 2500 mA.

The converter can be disabled to minimize battery drain. During shutdown, the load is completely disconnected from the battery. A low-EMI mode is implemented to reduce ringing and, in effect, lower radiated electromagnetic energy when the converter enters the discontinuous conduction mode.

The output voltage can be programmed by an external resistor divider or is fixed internally on the chip.

The device is packaged in a 16-pin VQFN 4-mm × 4-mm (16 RSA) package.
filter 尋找其它 AC/DC 和 DC/DC 轉換器 (整合式 FET)
下載 觀看有字幕稿的影片 影片

您可能會感興趣的類似產品

open-in-new 比較替代產品
功能相同，但引腳輸出與所比較的裝置不同
TPS61033 現行 具有電源良好、輸出放電和 PFM/PWM 控制的 5-V、5-A 升壓轉換器 5A/1.5A valley switch current limit and SOT583 packge with size of 2.1 x 1.2mm
功能與所比較的裝置相似
TPS610333 現行 具有電源良好、輸出放電和 PFM/PWM 控制的 5V、1.85A 升壓轉換器 1.85-A valley switch current limit and SOT583 package with size of 2.1 mm × 1.2 mm
TPS61230 現行 5-A 可調式輸出電壓高效同步升壓轉換器 For applications requiring smaller package or higher output current.

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 14
類型 標題 日期
* Data sheet TPS6109x Synchronous Boost Converter With 2-A Switch datasheet (Rev. C) PDF | HTML 2014年 12月 24日
Application note QFN and SON PCB Attachment (Rev. C) PDF | HTML 2023年 12月 6日
Application note Basic Calculation of a Boost Converter's Power Stage (Rev. D) PDF | HTML 2022年 10月 28日
Application note Performing Accurate PFM Mode Efficiency Measurements (Rev. A) 2018年 12月 11日
Selection guide Power Management Guide 2018 (Rev. R) 2018年 6月 25日
Application note Optimizing Transient Response of Internally Compensated DC-DC Converters (Rev. B) 2017年 11月 29日
Application note Extending the Soft Start Time Without a Soft Start Pin (Rev. B) 2017年 6月 15日
Application note Five Steps to a Good PCB Layout of the Boost Converter PDF | HTML 2016年 5月 3日
Application note Automated Frequency Response Analyzer 2013年 10月 9日
Analog Design Journal Design considerations for a resistive feedback divider in a DC/DC converter 2012年 4月 26日
Application note Choosing an Appropriate Pull-up/Pull-down Resistor for Open Drain Outputs 2011年 9月 19日
Analog Design Journal IQ: What it is, what it isn’t, and how to use it 2011年 6月 17日
Application note Minimizing Ringing at the Switch Node of a Boost Converter 2006年 9月 15日
EVM User's guide TPS61090EVM-029 User's Guide 2003年 10月 9日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TPS61070EVM-062 — TPS61070 評估模組

The TPS61070EVM-062 is an evaluation tool for the TPS61070 inductive step-up converter IC. The TPS61070 integrated boost converter can supply voltages up to 5.5V from an input of 0.9-V to 5.5-V and is packaged in a 6-pin thin SOT23. The TPS61070EVM-062 is set up to provide a 5-V output. By (...)

使用指南: PDF
TI.com 無法提供
開發板

TPS61090EVM-029 — TPS61090 評估模組

The TPS61090EVM-029 is an evaluation tool for the TPS61090 inductive step-up converter in QFN-16 package which can supply voltages up to 5.5V from a 1.8-V to 5.5-V input. The TPS61090EVM-029 uses a TPS61090 adjustable output step-up converter and the appropriate external components to provide a 5-V (...)

使用指南: PDF
TI.com 無法提供
Gerber 檔案

TPS6109xVM Gerber Files

SLVC141.ZIP (92 KB)
下載
封裝 針腳 CAD 符號、佔位空間與 3D 模型
VQFN (RSA) 16 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片