TPS709-Q1
- Qualified for Automotive Applications
- AEC-Q100 Qualified With the Following Results:
- Device Temperature Grade 1: –40°C to 125°C Ambient Operating Temperature
- Device HBM ESD Classification Level 2
- Device CDM ESD Classification Level C4B
- Input Voltage Range: 2.7 V to 30 V
- Ultralow IQ: 1 µA
- Reverse Current Protection
- Low ISHUTDOWN: 150 nA
- Supports 200-mA Peak Output
- 2% Accuracy Over Temperature
- Available in Fixed-Output Voltages:
1.2 V to 6.5 V - Thermal Shutdown and Overcurrent Protection
- Packages: SOT-23-5, WSON-6
The TPS709-Q1 series of linear regulators are ultralow, quiescent current devices designed for power-sensitive applications. A precision band-gap and error amplifier provides 2% accuracy over temperature. Quiescent current of only 1 µA makes these devices ideal solutions for battery-powered, always-on systems that require very little idle-state power dissipation. These devices have thermal-shutdown, current-limit, and reverse-current protections for added safety.
These regulators can be put into shutdown mode by pulling the EN pin low. The shutdown current in this mode goes down to 150 nA, typical.
The TPS709-Q1 series is available in WSON-6 and SOT-23-5 packages.
您可能會感興趣的類似產品
功能與所比較的裝置相似
技術文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 3 | 類型 | 標題 | 日期 | ||
|---|---|---|---|---|
| * | Data sheet | TPS709-Q1 150-mA, 30-V, 1-µA IQ Voltage Regulators With Enable datasheet (Rev. C) | PDF | HTML | 2018年 6月 7日 |
| Functional safety information | TPS709-Q1 Functional Safety FIT Rate and Failure Mode Distribution | 2019年 12月 17日 | ||
| User guide | TPS709xxEVM-110 Evaluation Module (Rev. A) | 2012年 9月 5日 |
設計與開發
如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。
開發板
TPS70933EVM-110 — TPS70933 評估模組
The Texas Instruments TPS70933EVM-110 evaluation module (EVM) is a fully-assembled and tested circuit for evaluating the TPS79033 low-dropout regulator. This stand alone EVM has a low-dropout regulator IC for positive fixed-voltage regulation at 150-mA, input and output capacitors for stable (...)
使用指南: PDF
參考設計
TIDA-020030 — SiC/IGBT 隔離式閘極驅動器參考設計，具備熱二極體與感測 FET
This reference design is an IGBT or SiC isolated gate driver power stage driving a IGBT module with advanced protection features. The design consists of a single phase power stage from a traction inverter supporting high level of safety features. The IGBT module has integrated thermal diode for (...)
參考設計
PMP40544 — 符合 3-m USB-IF 近端規範的車用 USB Type-A 充電器參考設計
This reference design is for an automotive USB Type-A charger with 3 meters USB-IF near-end compliant. The TPS25840-Q1 is used as DC-DC regulator and data switch and TUSB217-Q1 is used as high speed signal conditioner to improve signal quality. The efficiency of the solution is 93.3% at a 12-W (...)
參考設計
TIDA-020023 — 具有高精確度電流感測器的汽車正比電磁閥驅動參考設計
This reference design demonstrates precise proportional solenoid drive using a simple push-pull output comparator and highly-accurate, integrated current shunt monitor. Precise and accurate control of proportional solenoids is especially necessary in the automatic transmission of a vehicle for (...)
參考設計
TIDA-01500 — 用於 HVAC HMI 的車用多通道 LED 驅動器參考設計
In HVAC (heating, ventilation, and air conditioning) HMI (human machine interface) the displays and buttons are illuminated with many of LEDs. The drive circuit for these LEDs are traditionally realized in a discreet way so that an MCU drives external low side BJTs that sink current, limited by (...)
參考設計
TIDA-03050 — 車用 mA 至 kA 級電流分流感測器參考設計
This reference design shows how to detect current from the mA-to-KA range using a busbar-type shunt resistor. The increasing demand of high-capacity batteries in electric vehicles (EVs) and hybrid electric vehicles (HEVs) drives the requirement for larger current spans and highly-accurate current (...)
參考設計
TIDA-01506 — 車用比例式電磁閥電流感測器的參考設計
Precision control of automotive proportional solenoids is necessary to achieve the precise control in an automatic transmission, in electronic fuel injectors, and in several automotive actuator applications. In proportional solenoids, the current flowing through the coil is directly (...)
參考設計
PMP40312 — 車用雙 USB Type-C ™ PD DFP 5/9/12/15V 輸出汽車充電器參考設計
PMP40312 is a dual port USB Type-C™ PD car charger reference design. The design's normal input voltage range is from 9V to 14.5V, and the maximum input voltage can be to 42V.The pure analog configuration for the USB type-C source controller--TPS25740B makes the PD negotiation easy. The (...)
| 封裝 | 針腳 | CAD 符號、佔位空間與 3D 模型 |
|---|---|---|
| SOT-23 (DBV) | 5 | Ultra Librarian |
| WSON (DRV) | 6 | Ultra Librarian |
訂購與品質
內含資訊：
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 認證摘要
- 進行中持續性的可靠性監測
內含資訊：
- 晶圓廠位置
- 組裝地點
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。