홈 전원 관리 AC/DC 및 DC/DC 컨버터(통합 FET)
홈
전원 관리
AC/DC 및 DC/DC 컨버터(통합 FET)
신규

TPS546E25

미리 보기

4V~18V 입력, 50A, 적층형 PMBus 동기식 강압 컨버터

지금 주문
데이터 시트

TPS546E25

미리 보기
데이터 시트 지금 주문

제품 상세 정보

Rating Catalog Operating temperature range (°C) -40 to 125 Topology Buck Type Converter Iout (max) (A) 50 Vin (min) (V) 4 Vin (max) (V) 18 Switching frequency (min) (kHz) 400 Switching frequency (max) (kHz) 2000 Features Adaptive/Dynamic Voltage Scaling, Adjustable current limit, Differential Remote Sense, Enable, Extended security, Forced PWM, Over Current Protection, PMBUS, Phase Interleaving, Power good, Pre-Bias Start-Up, Soft Start Adjustable, Synchronous Rectification, UVLO adjustable, Voltage Margining Control mode D-CAP4 Vout (min) (V) 0.4 Vout (max) (V) 5.5 Iq (typ) (µA) 7500 Duty cycle (max) (%) 85
Rating Catalog Operating temperature range (°C) -40 to 125 Topology Buck Type Converter Iout (max) (A) 50 Vin (min) (V) 4 Vin (max) (V) 18 Switching frequency (min) (kHz) 400 Switching frequency (max) (kHz) 2000 Features Adaptive/Dynamic Voltage Scaling, Adjustable current limit, Differential Remote Sense, Enable, Extended security, Forced PWM, Over Current Protection, PMBUS, Phase Interleaving, Power good, Pre-Bias Start-Up, Soft Start Adjustable, Synchronous Rectification, UVLO adjustable, Voltage Margining Control mode D-CAP4 Vout (min) (V) 0.4 Vout (max) (V) 5.5 Iq (typ) (µA) 7500 Duty cycle (max) (%) 85
WQFN-FCRLF (RXX) 37 30 mm² 6 x 5
  • 4V to 18V input voltage without external bias
  • 2.7V to 18V input voltage with external bias
  • 0.4V to 5.5V output voltage
  • Supports 50A single-phase or 2 ×, 3 ×, or 4 × stacked configurations
  • Rdson_HS = 2.9mΩ, Rdson_LS = 1mΩ
  • 400kHz to 2MHz operating frequency (four discrete settings through pinstrap, additional settings through PMBus)
  • PMBus programmability
    • Revision 1.5 Compliant with PASSKEY security feature
    • Input voltage, output voltage, output current, temperature telemetry
    • Programmable overcurrent, overvoltage, undervoltage, overtemperature protections
    • Includes single command write function in stacked configuration
    • Extended write protection feature
    • Non-volatile memory to store configuration settings

  • Two methods for programming the output voltage

    • Internal resistor divider (discrete settings), with boot-up voltage selected by pin strapping
    • External resistor divider (continuous settings), with boot-up voltage selected by VBOOT field
  • Precision voltage reference and differential remote sense for high output accuracy
    • +/– 0.5% DAC accuracy from 0°C to 85°C junction
    • +/– 1% VOUT tolerance from –40°C to 125°C junction
  • Selectable FCCM/DCM in single phase only
  • Start-up without PMBus communication through pin strapping
  • Safe start-up into prebiased output
  • Programmable soft-start time from 0.5ms to 16ms
  • Programmable soft-stop time from 0.5ms to 4ms
  • D-CAP4 control topology with fast transient response, supporting all ceramic output capacitors
  • Programmable internal loop compensation
  • Selectable cycle-by-cycle valley current limit
  • Open-drain power-good output
  • 4V to 18V input voltage without external bias
  • 2.7V to 18V input voltage with external bias
  • 0.4V to 5.5V output voltage
  • Supports 50A single-phase or 2 ×, 3 ×, or 4 × stacked configurations
  • Rdson_HS = 2.9mΩ, Rdson_LS = 1mΩ
  • 400kHz to 2MHz operating frequency (four discrete settings through pinstrap, additional settings through PMBus)
  • PMBus programmability
    • Revision 1.5 Compliant with PASSKEY security feature
    • Input voltage, output voltage, output current, temperature telemetry
    • Programmable overcurrent, overvoltage, undervoltage, overtemperature protections
    • Includes single command write function in stacked configuration
    • Extended write protection feature
    • Non-volatile memory to store configuration settings

  • Two methods for programming the output voltage

    • Internal resistor divider (discrete settings), with boot-up voltage selected by pin strapping
    • External resistor divider (continuous settings), with boot-up voltage selected by VBOOT field
  • Precision voltage reference and differential remote sense for high output accuracy
    • +/– 0.5% DAC accuracy from 0°C to 85°C junction
    • +/– 1% VOUT tolerance from –40°C to 125°C junction
  • Selectable FCCM/DCM in single phase only
  • Start-up without PMBus communication through pin strapping
  • Safe start-up into prebiased output
  • Programmable soft-start time from 0.5ms to 16ms
  • Programmable soft-stop time from 0.5ms to 4ms
  • D-CAP4 control topology with fast transient response, supporting all ceramic output capacitors
  • Programmable internal loop compensation
  • Selectable cycle-by-cycle valley current limit
  • Open-drain power-good output

The TPS546E25 device is a highly integrated, buck converter with D-CAP4 control topology for fast transient response. All programmable parameters can be configured by the PMBus interface and stored in NVM as the new default values to minimize the external component count. Pinstrap options allow for configuration as primary or secondary, stack position and stack number, DCM (single phase only) or FCCM, overcurrent limit, fault response, internal or external feedback resistor, output voltage selection or range, switching frequency, and compensation.

The PMBus interface with 1MHz clock support gives a convenient, standardized digital interface for configuration as well as telemetry of key parameters including output voltage, output current, and internal die temperature. Response to fault conditions can be set to restart, latch off, or ignore, depending on system requirements. Two, three, and four TPS546E25 devices can be interconnected to provide up to 200A on a single output.

The device has an option to overdrive the internal 5V LDO with an external 5V supply through the VDRV and VCC pins to improve efficiency, reduce power dissipation, and enable start-up with a lower input voltage.

The TPS546E25 is a lead-free device and is RoHS compliant without exemption.

The TPS546E25 device is a highly integrated, buck converter with D-CAP4 control topology for fast transient response. All programmable parameters can be configured by the PMBus interface and stored in NVM as the new default values to minimize the external component count. Pinstrap options allow for configuration as primary or secondary, stack position and stack number, DCM (single phase only) or FCCM, overcurrent limit, fault response, internal or external feedback resistor, output voltage selection or range, switching frequency, and compensation.

The PMBus interface with 1MHz clock support gives a convenient, standardized digital interface for configuration as well as telemetry of key parameters including output voltage, output current, and internal die temperature. Response to fault conditions can be set to restart, latch off, or ignore, depending on system requirements. Two, three, and four TPS546E25 devices can be interconnected to provide up to 200A on a single output.

The device has an option to overdrive the internal 5V LDO with an external 5V supply through the VDRV and VCC pins to improve efficiency, reduce power dissipation, and enable start-up with a lower input voltage.

The TPS546E25 is a lead-free device and is RoHS compliant without exemption.
filter 기타 AC/DC 및 DC/DC 컨버터(통합 FET) 찾기
다운로드 스크립트와 함께 비디오 보기 동영상

기술 자료

star =TI에서 선정한 이 제품의 인기 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하십시오.
5개 모두 보기
유형 직함 날짜
* Data sheet TPS546E25 4V to 18V Input, 50A , 4 × Stackable, Synchronous Buck Converter With PMBus and Telemetry datasheet PDF | HTML 2024/07/12
Application note Point-of-Load Designs in Data Center Applications for Intel Xeon Sapphire Rapids Scalable Processors (Rev. C) PDF | HTML 2024/10/09
Application note TPS546E25 and TPS546C25 Advanced Product Errata PDF | HTML 2024/07/31
EVM User's guide TPS546E25EVM-1PH SWIFT™ Step-Down Converter Evaluation Module PDF | HTML 2024/07/15
Certificate TPS546E25EVM-1PH EU Declaration of Conformity (DoC) (Rev. A) 2024/07/09

설계 및 개발

추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.

평가 보드

TPS546E25EVM-1PH — TPS546E25 평가 모듈 단상

TPS546E25는 TPS546E25 장치를 사용하는 단상 벅 설계입니다. EVM은 공칭 12V 버스용으로 설계되었으며 최대 50A의 부하 전류에서 조정된 1.2V 출력을 생성합니다. TPS546E25EVM-1PH는 단상, 저출력 전압 애플리케이션에서 TPS546E25의 작동을 시연하는 동시에 디바이스의 성능을 평가하기 위한 여러 테스트 포인트를 제공하도록 설계되었습니다.

사용 설명서: PDF | HTML
TI.com에서 구매 불가
평가 보드

USB-TO-GPIO2 — USB-TO-GPIO2 USB 인터페이스 어댑터 평가 모듈

이 EVM은 표준 A 타입에서 미니-B USB 케이블을 통해 호스트 PC와 하나 또는 여러 대상 기기 사이의 인터페이스 어댑터 또는 브리지 역할을 합니다. USB 인터페이스 어댑터와 호스트 PC 간의 통신은 USB를 통해 이루어집니다. USB 인터페이스 어댑터와 대상 장치 간의 통신은 상호 통합 회로(I²C), 범용 입력 및 출력 GPIO 또는 둘 다를 통해 이루어집니다. 이 브리지는 USB와 I²C/GPIO 간의 통신 트랜잭션을 변환합니다.
사용 설명서: PDF | HTML
TI.com에서 구매 불가
설계 툴

TPS546E25-DESIGN — TPS546E25 Design file

Design files for TPS546E25
지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

제품
AC/DC 및 DC/DC 컨버터(통합 FET)
TPS546C25 — 4V~-18V 입력, 35A, 적층형 PMBus 동기식 스텝다운 컨버터 TPS546E25 — 4V~18V 입력, 50A, 적층형 PMBus 동기식 강압 컨버터
다운로드 옵션
패키지 핀 CAD 기호, 풋프린트 및 3D 모델
WQFN-FCRLF (RXX) 37 Ultra Librarian
TI의 평가 항목에 대한 표준 약관이 적용됩니다.

주문 및 품질

포함된 정보:
  • RoHS
  • REACH
  • 디바이스 마킹
  • 납 마감/볼 재질
  • MSL 등급/피크 리플로우
  • MTBF/FIT 예측
  • 물질 성분
  • 인증 요약
  • 지속적인 신뢰성 모니터링
포함된 정보:
  • 팹 위치
  • 조립 위치

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

포럼 주제 모두 보기(영문)

콘텐츠는 TI 및 커뮤니티 기고자에 의해 "있는 그대로" 제공되며 TI의 사양으로 간주되지 않습니다. 사용 약관을 참조하십시오.

품질, 패키징, TI에서 주문하는 데 대한 질문이 있다면 TI 지원을 방문하세요. ​​​​​​​​​​​​​​

동영상