TLK106

不推薦在新設計中採用

工業溫度單埠 10/100Mbps 乙太網路實體層收發器

立即訂購

產品規格表

document-pdfAcrobat TLK105 TLK106 Industrial Temp, Single Port 10/100Mbs Ethernet Physical Layer Transceiver datasheet (Rev. C) (英文) PDF | HTML

TLK106

不推薦在新設計中採用

產品規格表

立即訂購

產品詳細資料

Datarate (Mbps)

10/100

Interface type

MII, RMII

Number of ports

Single

Rating

Catalog

Features

Cable diagnostics

Supply voltage (V)

3.3

Operating temperature range (°C)

0 to 0

Number of LEDs

1

ESD HBM (kV)

16

Datarate (Mbps)

10/100

Interface type

MII, RMII

Number of ports

Single

Rating

Catalog

Features

Cable diagnostics

Supply voltage (V)

3.3

Operating temperature range (°C)

0 to 0

Number of LEDs

1

ESD HBM (kV)

16

VQFN (RHB)

32

25 mm² 5 x 5

Low Power Consumption:
- Single Supply: <205mW PHY, 275mW with
  Center Tap (Typical)
- Dual Supplies: <126mW PHY, 200mW with
  Center Tap (Typical)
Programmable Power Back Off to reduce PHY
power up to 20% in systems with shorter cables
Low deterministic latency supports IEEE1588
implementation
Cable Diagnostics (TLK106)
Programmable Fast Link Down Modes, <10µs
reaction time
Variable I/O voltage range: 3.3V, 2.5V, 1.8V
MAC Interface I/O voltage range:
- MII I/O voltage range: 3.3V, 2.5V, 1.8V
- RMII I/O voltage range: 3.3V, 2.5V
Fixed TX Clock to XI, with programmable phase
shift
Auto-MDIX for 10/100Mbs
Energy Detection Mode
MII and RMII Capabilities
Serial Management Interface
IEEE 802.3u MII
IEEE 802.3u Auto-Negotiation and Parallel
Detection
Error-Free 100Base-T Operation up to 150 Meters
Under Typical Conditions
Error-Free 10Base-T Operation up to 300 Meters
Under Typical Conditions
IEEE 802.3u ENDEC, 10Base-T
Transceivers and Filters
IEEE 802.3u PCS, 100Base-TX Transceivers
Integrated ANSI X3.263 Compliant TP-PMD
Physical Sublayer with Adaptive Equalization and
Baseline Wander Compensation
Programmable LED Support Link, Activity
10/100Mbs Packet BIST (Built in Self Test)
HBM ESD protection on RD± and TD± of 16kV
32-pin QFN (5mm) × (5mm)

Low Power Consumption:
- Single Supply: <205mW PHY, 275mW with
  Center Tap (Typical)
- Dual Supplies: <126mW PHY, 200mW with
  Center Tap (Typical)
Programmable Power Back Off to reduce PHY
power up to 20% in systems with shorter cables
Low deterministic latency supports IEEE1588
implementation
Cable Diagnostics (TLK106)
Programmable Fast Link Down Modes, <10µs
reaction time
Variable I/O voltage range: 3.3V, 2.5V, 1.8V
MAC Interface I/O voltage range:
- MII I/O voltage range: 3.3V, 2.5V, 1.8V
- RMII I/O voltage range: 3.3V, 2.5V
Fixed TX Clock to XI, with programmable phase
shift
Auto-MDIX for 10/100Mbs
Energy Detection Mode
MII and RMII Capabilities
Serial Management Interface
IEEE 802.3u MII
IEEE 802.3u Auto-Negotiation and Parallel
Detection
Error-Free 100Base-T Operation up to 150 Meters
Under Typical Conditions
Error-Free 10Base-T Operation up to 300 Meters
Under Typical Conditions
IEEE 802.3u ENDEC, 10Base-T
Transceivers and Filters
IEEE 802.3u PCS, 100Base-TX Transceivers
Integrated ANSI X3.263 Compliant TP-PMD
Physical Sublayer with Adaptive Equalization and
Baseline Wander Compensation
Programmable LED Support Link, Activity
10/100Mbs Packet BIST (Built in Self Test)
HBM ESD protection on RD± and TD± of 16kV
32-pin QFN (5mm) × (5mm)

The TLK10x is a single-port Ethernet PHY for 10Base-T and 100Base TX signaling. This device integrates all the physical-layer functions needed to transmit and receive data on standard twisted-pair cables. The TLK10x supports the standard Media Independent Interface (MII) and Reduced Media Independent Interface (RMII) for direct connection to a Media Access Controller (MAC).

The TLK10x is designed for power-supply flexibility, and can operate with a single 3.3V power supply or with combinations of 3.3V and 1.55V power supplies for reduced power operation.

The TLK10x uses mixed-signal processing to perform equalization, data recovery, and error correction to achieve robust operation over CAT 5 twisted-pair wiring. This device not only meets the requirements of IEEE 802.3, but maintains high margins in terms of cross-talk and alien noise.

The TLK10x Ethernet PHY has a special Power Back Off mode to conserve power in systems with relatively short cables. This mode provides the flexibility to reduce system power when the system is not required to drive the standard IEEE 802.3 100m cable length, or the extended 150m, error-free cable reach of the TLK10x. For more detail, see application note SLLA328.

The TLK10x is a single-port Ethernet PHY for 10Base-T and 100Base TX signaling. This device integrates all the physical-layer functions needed to transmit and receive data on standard twisted-pair cables. The TLK10x supports the standard Media Independent Interface (MII) and Reduced Media Independent Interface (RMII) for direct connection to a Media Access Controller (MAC).

The TLK10x is designed for power-supply flexibility, and can operate with a single 3.3V power supply or with combinations of 3.3V and 1.55V power supplies for reduced power operation.

The TLK10x uses mixed-signal processing to perform equalization, data recovery, and error correction to achieve robust operation over CAT 5 twisted-pair wiring. This device not only meets the requirements of IEEE 802.3, but maintains high margins in terms of cross-talk and alien noise.

The TLK10x Ethernet PHY has a special Power Back Off mode to conserve power in systems with relatively short cables. This mode provides the flexibility to reduce system power when the system is not required to drive the standard IEEE 802.3 100m cable length, or the extended 150m, error-free cable reach of the TLK10x. For more detail, see application note SLLA328.

filter

尋找其它乙太網路 PHY

下載

技術文件

star

=TI 所選的此產品重要文件

找不到結果。請清除您的搜尋條件，然後再試一次。

檢視所有 1

	類型	標題		日期
*	Data sheet	TLK105 TLK106 Industrial Temp, Single Port 10/100Mbs Ethernet Physical Layer Transceiver datasheet (Rev. C)	PDF \| HTML	2016年 4月 22日

TLK106

工業溫度單埠 10/100Mbps 乙太網路實體層收發器

TLK106

產品詳細資料

技術文件

訂購與品質