首頁 電源管理 AC/DC 和 DC/DC 控制器 (外部 FET)
首頁
電源管理
AC/DC 和 DC/DC 控制器 (外部 FET)

UCC28056

現行

6 針腳高效能 CRM/DCM PFC 控制器

立即訂購
產品規格表

UCC28056

現行
產品規格表 立即訂購

產品詳細資料

Vin (max) (V) 34 Operating temperature range (°C) -40 to 125 Control mode TM Topology Boost, PFC controller Rating Catalog Features < 150 W applications, Audible Noise Minimization, Low power, OVP, Overvoltage protection, Peak current mode, Programmable soft start, Single-phase, Transition Control Mode, USB C/PD compatible Duty cycle (max) (%) 1
Vin (max) (V) 34 Operating temperature range (°C) -40 to 125 Control mode TM Topology Boost, PFC controller Rating Catalog Features < 150 W applications, Audible Noise Minimization, Low power, OVP, Overvoltage protection, Peak current mode, Programmable soft start, Single-phase, Transition Control Mode, USB C/PD compatible Duty cycle (max) (%) 1
SOT-23 (DBV) 6 8.12 mm² 2.9 x 2.8
  • Ultra-low no-load input power enables < 80-mW standby power at 230 VAC in PFC+LLC system
  • Excellent light load efficiency and high efficiency over wide range of load due to multi-mode TM and DCM control
  • Enables low system cost through FET drain valley synchronized turn-on which eliminates need for second winding on the boost inductor
  • Enables compliance to green power standards without disabling PFC
    • EuP Lot 6 Tier 2, CoC Ver. 5 Tier 2, Energy Star Ver. 6.1, DoE Level VI
  • Burst mode with soft-entry and soft-exit periods enables ultra-low audible noise output
  • Enhanced error amplifier, responds rapidly to load steps without degrading input current distortion
  • User adjustable valley delay ensures valley switching
  • Low start-up current consumption (<46 µA)
  • Wide VCC range 8.5 V to 34 V
  • Cycle-by-cycle current limit
  • Second independent output over-voltage protection
  • Integrated over-temperature protection
  • Create a custom design using the UCC28056 device with the WEBENCH® Power Designer
  • Ultra-low no-load input power enables < 80-mW standby power at 230 VAC in PFC+LLC system
  • Excellent light load efficiency and high efficiency over wide range of load due to multi-mode TM and DCM control
  • Enables low system cost through FET drain valley synchronized turn-on which eliminates need for second winding on the boost inductor
  • Enables compliance to green power standards without disabling PFC
    • EuP Lot 6 Tier 2, CoC Ver. 5 Tier 2, Energy Star Ver. 6.1, DoE Level VI
  • Burst mode with soft-entry and soft-exit periods enables ultra-low audible noise output
  • Enhanced error amplifier, responds rapidly to load steps without degrading input current distortion
  • User adjustable valley delay ensures valley switching
  • Low start-up current consumption (<46 µA)
  • Wide VCC range 8.5 V to 34 V
  • Cycle-by-cycle current limit
  • Second independent output over-voltage protection
  • Integrated over-temperature protection
  • Create a custom design using the UCC28056 device with the WEBENCH® Power Designer

The UCC28056 device drives PFC boost stages based on an innovative mixed mode method that operates in transition mode (TM) at full load and transitions seamlessly into discontinuous conduction mode (DCM) at reduced load, automatically reducing switching frequency. This device incorporates burst mode operation to further improve light load performance, enabling systems to meet challenging energy standards while eliminating the need to switch off the PFC. UCC28056 can drive a PFC power stage up to 300 W, ensuring sinusoidal line input current with low distortion, close to unity power factor. When used with the LLC controller UCC256403/4, and dual synchronous rectifier controller UCC24624 less than 80 mW system standby power can be achieved, enabling PFC always on architecture and eliminating the need for an auxiliary converter. This with FET Drain valley turn-on with simple boost inductor allows fewest component count and reduced system cost.

The UCC28056 device drives PFC boost stages based on an innovative mixed mode method that operates in transition mode (TM) at full load and transitions seamlessly into discontinuous conduction mode (DCM) at reduced load, automatically reducing switching frequency. This device incorporates burst mode operation to further improve light load performance, enabling systems to meet challenging energy standards while eliminating the need to switch off the PFC. UCC28056 can drive a PFC power stage up to 300 W, ensuring sinusoidal line input current with low distortion, close to unity power factor. When used with the LLC controller UCC256403/4, and dual synchronous rectifier controller UCC24624 less than 80 mW system standby power can be achieved, enabling PFC always on architecture and eliminating the need for an auxiliary converter. This with FET Drain valley turn-on with simple boost inductor allows fewest component count and reduced system cost.
filter 尋找其它 AC/DC 和 DC/DC 控制器 (外部 FET)
下載 觀看有字幕稿的影片 影片

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 13
類型 標題 日期
* Data sheet UCC28056 6-Pin Single-Phase Transition-Mode PFC Controller datasheet (Rev. E) PDF | HTML 2019年 8月 28日
Product overview PFC Controller Step-by-Step Selection Guide PDF | HTML 2023年 2月 28日
Application note UCC28056 System Bring Up Guidelines and Application Debug FAQ PDF | HTML 2021年 10月 8日
Technical article How to reduce audible noise and power consumption at standby in your AC/DC design PDF | HTML 2020年 4月 22日
EVM User's guide UCC28056EVM-296 Evaluation Module User Guide (Rev. C) 2019年 10月 31日
Application note Optimizing Efficiency and Standby Power With the UCC28056 in Offline Application (Rev. B) 2019年 8月 13日
Application brief Exceeding Modern Energy Standards with 'Always On' PFC and LLC Controllers​ (Rev. B) 2019年 8月 1日
Application note UCC28056,Using Auxiliary winding voltage for driving ZCD/CS Pin (Rev. B) 2019年 8月 1日
EVM User's guide PFCLLCSREVM-034 User Guide 2019年 7月 26日
Application note UCC28056 Selection Guide 2019年 6月 24日
Technical article Three considerations for achieving high efficiency and reliability in industrial A PDF | HTML 2019年 4月 4日
Technical article Gain ultra-high power density for 100-W USB Power Delivery adapters PDF | HTML 2019年 3月 5日
Technical article Crank up your power supply with LLC controllers PDF | HTML 2017年 10月 23日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

PFCLLCSREVM034 — 具有 UCC28056B、UCC256404 和 UCC24624 的 AC 至隔離式 DC EVM

PFCLLCSREVM034 is a 168-W AC/DC supply with a transition-mode power-factor-correction front end and isolated half-bridge LLC resonant converter with synchronous rectification. This EVM accepts AC input from 90 Vrms to 264 Vrms and outputs 12-V DC with 168-W full-load output power.

使用指南: PDF
TI.com 無法提供
開發板

UCC28056EVM-296 — UCC28056 PFC 評估板

The UCC28056EVM is an EVM of PFC converter with UCC28056, a CrM/DCM Mixed Mode PFC Controller. The EVM accepts an input of 85Vac to 265Vac and provides an output of 390Vdc with full load output power of 165W.

使用指南: PDF
TI.com 無法提供
模擬型號

UCC28056 SIMPLIS Transient Model

SLUM620.ZIP (157 KB) - SIMPLIS Model
下載
模擬型號

UCC28056A SIMPLIS MODEL (Rev. A)

SLUM688A.ZIP (241 KB) - SIMPLIS Model
下載
模擬型號

UCC28056B SIMPLIS MODEL (Rev. A)

SLUM689A.ZIP (241 KB) - SIMPLIS Model
下載
模擬型號

UCC28056C SIMPLIS MODEL (Rev. A)

SLUM690A.ZIP (231 KB) - SIMPLIS Model
下載
計算工具

SLUC641 — UCC28056x Design Calculator

支援產品和硬體

支援產品和硬體

產品
AC/DC 和 DC/DC 控制器 (外部 FET)
UCC28056 — 6 針腳高效能 CRM/DCM PFC 控制器
下載
參考設計

TIDA-050074 — 140-W GaN 式 USB PD3.1 USB-C® 變壓器參考設計

‌此參考設計是基於氮化鎵 (GaN) 的 140W AC-DC 電源，具有高效率和功率密度。支援廣泛輸入 (90VAC 至 264VAC) 和輸出 (5V 至 28V) 電壓。它專為應用而設計，例如用於 USB PD3.1 的變壓器設計和用於電動工具的充電器。
Design guide: PDF
參考設計

PMP21251 — 低於 90mW 超低待機功耗無輔助 AC-DC 電源供應參考設計

The PMP21251 reference design uses UCC28056 CRM/DCM PFC controller and UCC256304 enhanced LLC controller with integrated driver to provide 12V/10.8A output (continuous, 14.4A peak) from universal AC input. This design achieves 92.4% peak efficiency at 115VAC input and 94.0% peak efficiency at (...)
Test report: PDF
電路圖: PDF
參考設計

TIDA-01623 — 30-W/in3、93.4% 效率、100-W AC/DC 變壓器參考設計

This fully-tested reference design is a high-efficiency, high-power-density, AC/DC adapter solution with a wide input voltage range (100- to 240-V AC) for laptop adapters and smartphone charger applications. This design consists of a front-end transition-mode (TM) power factor correction (PFC) (...)
Design guide: PDF
電路圖: PDF
參考設計

PMP23224 — 220 W 主動箝位電池充電器參考設計

此參考設計為搭載功率因數校正 (PFC) 前端的 220-W 主動箝位返馳電池充電器設計。此設計採用 90 V 至 264 V 通用 AC 輸入，並以 6-V 至 22-V VOUT 範圍進行電池充電。
Test report: PDF
參考設計

PMP40580 — 180-W 通用輸入 PFC + LLC TV 電源供應參考設計

This AC to DC power supply design for TV application provides 12-V, 5-A and 150-V, 0.8-A output from universal AC voltage (90 Vac to 264 Vac). The design uses CRM/DCM PFC controller UCC28056, and LLC controller UCC256404 with enhanced burst mode which enabled for low standby power and smaller (...)
Test report: PDF
電路圖: PDF
參考設計

TIDA-010047 — 採用 Si MOSFET 的 22-W/in3、93.1% 峰值效率、100-W USB-PD 3.0 AC/DC 適配器參考設計

This fully-tested reference design is a high-efficiency, high-power-density, AC/DC adapter solution with a wide input voltage range (100- to 240-V AC) for laptop adapters and smartphone charger applications. This design consists of a front-end transition-mode (TM) power factor correction (PFC) (...)
Design guide: PDF
電路圖: PDF
參考設計

PMP22087 — 具有 80 PLUS 白金相容性能的 336-W 無輔助 AC/DC 電源供應參考設計

This reference design is an AC/DC power supply design with critical conduction mode (CRM) PFC and half-bridge LLC series resonant converter that provides 24 V, 240-W continuous, 336-W peak output from a universal input AC voltage (90 VAC to 264 VAC). This design uses UCC28056 CRM/DCM PFC (...)
Test report: PDF
電路圖: PDF
參考設計

PMP21098 — 具有 80 PLUS Gold 相容性能的 170W 無輔助 AC/DC 電源參考設計

The PMP21098 reference design uses UCC28056 transition mode PFC controller and UCC25630 enhanced LLC controller with integrated driver to provide 12V/10.8A output (continuous, 14.2A peak) from universal AC input. This design achieves 91.8% peak efficiency at 115VAC input and 93.4% peak efficiency (...)
Test report: PDF
電路圖: PDF
封裝 針腳 CAD 符號、佔位空間與 3D 模型
SOT-23 (DBV) 6 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片