Startseite Energiemanagement AC/DC- und DC/DC-Wandler (integrierter FET)
Startseite
Energiemanagement
AC/DC- und DC/DC-Wandler (integrierter FET)

LM7705

AKTIV

Rauscharmer Vorspannungsgenerator, negativ

Jetzt bestellen
Datenblatt

Eine neuere Version dieses Produkts ist verfügbar

open-in-new Alternativen vergleichen
Selbe Funktionalität wie der verglichene Baustein bei abweichender Anschlussbelegung
LM27761 AKTIV Rauscharmer geregelter Inverter mit integriertem LDO Smaller solution size and higher output current up to 200 mA

LM7705

AKTIV
Datenblatt Jetzt bestellen

Produktdetails

Rating Catalog Operating temperature range (°C) -40 to 125 Type Charge pump, Converter Iout (max) (A) 0.026 Vin (min) (V) 3 Vin (max) (V) 5.25 Switching frequency (min) (kHz) 92 Switching frequency (max) (kHz) 92 Features Enable, Regulated, Synchronous Rectification Vout (min) (V) -0.232 Vout (max) (V) -0.232 Iq (typ) (µA) 78
Rating Catalog Operating temperature range (°C) -40 to 125 Type Charge pump, Converter Iout (max) (A) 0.026 Vin (min) (V) 3 Vin (max) (V) 5.25 Switching frequency (min) (kHz) 92 Switching frequency (max) (kHz) 92 Features Enable, Regulated, Synchronous Rectification Vout (min) (V) -0.232 Vout (max) (V) -0.232 Iq (typ) (µA) 78
VSSOP (DGK) 8 14.7 mm² 3 x 4.9
  • Regulated Output Voltage −0.232 V
  • Output Voltage Tolerance 5%
  • Output Voltage Ripple 4 mVPP
  • Supply Voltage 3 V to 5.25 V
  • Conversion Efficiency Up to 98%
  • Quiescent Current 78 µA
  • Shutdown Current 20 nA
  • Turnon Time 500 µs
  • Operating Temperature Range −40°C to 125°C
  • 8-Pin VSSOP Package
  • Regulated Output Voltage −0.232 V
  • Output Voltage Tolerance 5%
  • Output Voltage Ripple 4 mVPP
  • Supply Voltage 3 V to 5.25 V
  • Conversion Efficiency Up to 98%
  • Quiescent Current 78 µA
  • Shutdown Current 20 nA
  • Turnon Time 500 µs
  • Operating Temperature Range −40°C to 125°C
  • 8-Pin VSSOP Package

The LM7705 device is a switched capacitor voltage inverter with a low noise, −0.23 V fixed negative voltage regulator. This device is designed to be used with low voltage amplifiers to enable the amplifiers output to swing to zero volts. The −0.23 V is used to supply the negative supply pin of an amplifier while maintaining less then 5.5 V across the amplifier. Rail-to-Rail output amplifiers cannot output zero volts when operating from a single-supply voltage and can result in error accumulation due to amplifier output saturation voltage being amplified by following gain stages. A small negative supply voltage will prevent the amplifiers output from saturating at zero volts and will help maintain an accurate zero through a signal processing chain. Additionally, when an amplifier is used to drive an input of the ADC, the amplifier can output a zero voltage signal and the full input range of an ADC can be used. The LM7705 device has a shutdown pin to minimize standby power consumption.

The LM7705 device is a switched capacitor voltage inverter with a low noise, −0.23 V fixed negative voltage regulator. This device is designed to be used with low voltage amplifiers to enable the amplifiers output to swing to zero volts. The −0.23 V is used to supply the negative supply pin of an amplifier while maintaining less then 5.5 V across the amplifier. Rail-to-Rail output amplifiers cannot output zero volts when operating from a single-supply voltage and can result in error accumulation due to amplifier output saturation voltage being amplified by following gain stages. A small negative supply voltage will prevent the amplifiers output from saturating at zero volts and will help maintain an accurate zero through a signal processing chain. Additionally, when an amplifier is used to drive an input of the ADC, the amplifier can output a zero voltage signal and the full input range of an ADC can be used. The LM7705 device has a shutdown pin to minimize standby power consumption.
filter Andere AC/DC- und DC/DC-Wandler (integrierter FET) suchen
Herunterladen Video mit Transkript ansehen Video

Technische Dokumentation

star =Von TI ausgewählte Top-Empfehlungen für dieses Produkt
Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
Alle anzeigen 7
Typ Titel Datum
* Data sheet LM7705 Low-Noise Negative Bias Generator datasheet (Rev. D) PDF | HTML 08 Mai 2018
Circuit design Charge pump circuit (–0.3V) for negative amplifier supply (Rev. A) PDF | HTML 21 Aug 2024
Application note Quick Reference Guide To TI Buck Switching DC/DC Application Notes (Rev. B) PDF | HTML 23 Mai 2022
Technical article How to achieve microvoltage-level precision in thermopile applications PDF | HTML 09 Dez 2021
Application note Attenuator Amplifier Design to Maximize the Input Voltage of Differential ADCs 14 Jun 2018
Technical article Unique active mux capability combines buffer and switch into one solution PDF | HTML 10 Okt 2017
EVM User's guide AN-1883 LM7705 Evaluation Board (Rev. B) 03 Mai 2013

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Evaluierungsplatine

ADS8168EVM-PDK — ADS8168 8-Kanal, 16 Bit, 1-MSPS-SAR-ADC – Evaluierungsmodul/Leistungs-Demokit (PDK)

The ADS8168 evaluation module (EVM) performance demonstration kit (PDK) is a platform for evaluating the performance of the ADS8168 successive-approximation register (SAR) analog-to-digital converter (ADC). The ADS8168EVM-PDK includes the ADS8168EVM board, the precision host interface (PHI) (...)

Benutzerhandbuch: PDF
Nicht verfügbar auf TI.com
Evaluierungsplatine

LM7705MMEVAL — Evaluierungsplatine für den LM7705

This evaluation board is designed to demonstrate the functionality of Texas Instruments LM7705 Low Noise Negative Bias Generator. The board has a dual Operational Amplifier that can be connected to ground or biased with the on board LM7705. In the last case a True zero amplifier is demonstrated.

Benutzerhandbuch: PDF
Nicht verfügbar auf TI.com
Referenzdesigns

TIDA-01056 — Referenzdesign für 20-Bit-1-MSPS-DAQ zur Optimierung der Stromversorgungseffizienz bei gleichzeitige

This reference design for high performance data acquisition (DAQ) systems optimizes power stage in order to reduce power consumption and minimize the effect of EMI from switching regulator by using LMS3635-Q1 buck converter.  This reference designs yields 7.2% efficiency improvement at most (...)
Design guide: PDF
Schaltplan: PDF
Referenzdesigns

TIDA-01054 — Multi-Rail-Leistungs-Referenzdesign zur Eliminierung von EMI-Effekten in Hochleistungs-DAQ-Systemen

The TIDA-01054 reference design helps eliminate the performance degrading effects of EMI on Data Acquisition (DAQ) systems greater than 16 bits with the help of the LM53635 buck converter. The buck converter enables the designer to place power solutions close to the signal path without the (...)
Design guide: PDF
Schaltplan: PDF
Referenzdesigns

TIDA-01042 — Referenzdesign für modulare Batterietester für 50-A-, 100-A- und 200-A-Anwendungen

This reference design provides a modular battery test solution allowing users to have the flexibility to test batteries at different current levels with one design. This design leverages the TIDA-01041 reference design by providing two 100-A battery testers that can work independently or be (...)
Design guide: PDF
Schaltplan: PDF
Referenzdesigns

TIDA-01055 — ADC-Spannungsreferenzpuffer-Optimierung – Referenzdesign für Hochleistungs-DAQ-Systeme

The TIDA-01055 reference design for high performance DAQ Systems optimizes the ADC reference buffer to improve SNR performance and reduce power consumption with the TI OPA837 high-speed op amp. This device is used in a composite buffer configuration and provides a 22% power improvement over (...)
Design guide: PDF
Schaltplan: PDF
Referenzdesigns

TIDA-01057 — Referenzdesign Maximierung des dynamischen Signalbereichs für echten Differenzeingang von 10 Vpp bis

This reference design is designed for high performance data acquisition(DAQ) systems to improve the dynamic range of 20 bit differential input ADCs. Many DAQ systems require the measurement capability at a wide FSR (Full Scale Range) in order to obtain sufficient signal dynamic range. Many earlier (...)
Design guide: PDF
Schaltplan: PDF
Referenzdesigns

TIDA-01051 — Referenzdesign zur Optimierung der FPGA-Auslastung und des Datendurchsatzes für automatische Prüfger

The TIDA-01051 reference design is used to demonstrate optimized channel density, integration, power consumption, clock distribution and signal chain performance of very high channel count data acquisition (DAQ) systems such as those used in automatic test equipment (ATE). Using serializers, such (...)
Design guide: PDF
Schaltplan: PDF
Referenzdesigns

TIDA-01050 — Referenzdesign eines optimierten Analog-Frontend-Datenerfassungssystems für 18-Bit-SAR-Datenwandler

The TIDA-01050 reference design aims to improve the integration, power consumption, performance, and clocking issues typically associated with automatic test equipment. This design is applicable to any ATE system but most applicable to systems requiring a large number of input channels.
Design guide: PDF
Schaltplan: PDF
Referenzdesigns

TIDA-01052 — ADC-Treiber-Referenzdesign zur Verbesserung des Full Scale THD bei negativer Versorgung

The TIDA-01052 reference design aims to highlight system performance increases seen using a negative voltage rail on the analog front end driver amplifiers rather than ground. This concept is relative to all analog front ends, however this design is aimed specifically at automatic test equipment.
Design guide: PDF
Schaltplan: PDF
Referenzdesigns

TIPD129 — Lowside-Stromsensorlösung für einzelne Stromversorgung, 0–1 A

This TI Verified Design implements a single-supply, low-side current sensing solution that can accurately detect load current from 0-1A.  The corresponding linear output range is from 0V to 4.9V. This design relies on the LM7705 inverting charge pump to bias the negative supply of the OPA320 to (...)
Benutzerhandbuch: PDF
Schaltplan: PDF
Referenzdesigns

TIDA-00187 — Erweiterter Rail-to-Rail-Ausgangsbereich für Volldifferenzialverstärker um echte null Volt

Operational amplifiers (op amps) have been used for decades in signal conditioning circuits and measurement systems. An op amp that has an output spanning from negative to positive supply rail are generally referred to as rail-to-rail output (RRO) op amps. These devices have been used increasingly (...)
Design guide: PDF
Schaltplan: PDF
Gehäuse Pins CAD-Symbole, Footprints und 3D-Modelle
VSSOP (DGK) 8 Ultra Librarian
Es gelten die allgemeinen Geschäftsbedingungen von TI für Evaluierungsartikel.

Bestellen & Qualität

Beinhaltete Information:
  • RoHS
  • REACH
  • Bausteinkennzeichnung
  • Blei-Finish/Ball-Material
  • MSL-Rating / Spitzenrückfluss
  • MTBF-/FIT-Schätzungen
  • Materialinhalt
  • Qualifikationszusammenfassung
  • Kontinuierliches Zuverlässigkeitsmonitoring
Beinhaltete Information:
  • Werksstandort
  • Montagestandort

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Alle Forenthemen auf Englisch anzeigen

Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

Videos