Startseite Energiemanagement AC/DC- und DC/DC-Wandler (integrierter FET)
Startseite
Energiemanagement
AC/DC- und DC/DC-Wandler (integrierter FET)

TPIC74100-Q1

AKTIV

Abwärts-/Aufwärtswandler, 550 kHz, 1,5 bis 40 V, 1 A, mit fester Ausgangsspannung von 5 V, AEC-Q100-

Jetzt bestellen
Datenblatt

Eine neuere Version dieses Produkts ist verfügbar

open-in-new Alternativen vergleichen
Selbe Funktionalität wie der verglichene Baustein bei abweichender Anschlussbelegung
TPS55165-Q1 AKTIV 2 V bis 36 V, 1 A-Ausgang, 2 MHz, 5 V oder 12 V feste Ausgangsspannung, Aufwärts- und Abwärtswandler TPS55165 has 2-Mhz switching frequency and higher Iout

TPIC74100-Q1

AKTIV
Datenblatt Jetzt bestellen

Produktdetails

Rating Automotive Operating temperature range (°C) -40 to 125 Topology Buck-Boost Type Converter Vin (min) (V) 1.5 Vin (max) (V) 40 Switching frequency (min) (kHz) 330 Switching frequency (max) (kHz) 550 Features Enable, Light Load Efficiency, Power good, Synchronous Rectification Vout (min) (V) 5 Vout (max) (V) 5 Iq (typ) (µA) 100 Duty cycle (max) (%) 99 Switch current limit (typ) (A) 1.5
Rating Automotive Operating temperature range (°C) -40 to 125 Topology Buck-Boost Type Converter Vin (min) (V) 1.5 Vin (max) (V) 40 Switching frequency (min) (kHz) 330 Switching frequency (max) (kHz) 550 Features Enable, Light Load Efficiency, Power good, Synchronous Rectification Vout (min) (V) 5 Vout (max) (V) 5 Iq (typ) (µA) 100 Duty cycle (max) (%) 99 Switch current limit (typ) (A) 1.5
HTSSOP (PWP) 20 41.6 mm² 6.5 x 6.4
  • Qualified for Automotive Applications
  • AEC-Q100 Qualified With the Following Results:
    • Device HBM ESD Classification level 1B for
      pin 7 (L2), pin 8 (VOUT), pin 9 (5Vg)
    • Device HBM ESD Classification 2 for pins 1–6
      and 10–20
    • Device CDM ESD Classification Level C4B
  • Switch-Mode Regulator
    • 5 V ±2%, Normal Mode
    • 5 V ±3%, Low-Power or Crossover Mode
  • Switching Frequency, 440 kHz (typical)
  • Input Operating Range, 1.5 V to 40 V, (Vdriver)
    • 1-A Load-Current Capability
    • 200-mA Load-Current Capability Down to 2-V
      Input (Vdriver)
    • 120-mA Load-Current Capability Down to
      1.5-V Input (Vdriver)
  • Enable Function
  • Low-Power Operation Mode
  • Switched 5-V Regulated Output on 5Vg With
    Current Limit
  • Programmable Slew Rate and Frequency
    Modulation for EMI Consideration
  • Reset Function With Deglitch Timer and
    Programmable Delay
  • Alarm Function for Undervoltage Detection and
    Indication
  • Thermally Enhanced Package for Efficient Heat
    Management
  • Qualified for Automotive Applications
  • AEC-Q100 Qualified With the Following Results:
    • Device HBM ESD Classification level 1B for
      pin 7 (L2), pin 8 (VOUT), pin 9 (5Vg)
    • Device HBM ESD Classification 2 for pins 1–6
      and 10–20
    • Device CDM ESD Classification Level C4B
  • Switch-Mode Regulator
    • 5 V ±2%, Normal Mode
    • 5 V ±3%, Low-Power or Crossover Mode
  • Switching Frequency, 440 kHz (typical)
  • Input Operating Range, 1.5 V to 40 V, (Vdriver)
    • 1-A Load-Current Capability
    • 200-mA Load-Current Capability Down to 2-V
      Input (Vdriver)
    • 120-mA Load-Current Capability Down to
      1.5-V Input (Vdriver)
  • Enable Function
  • Low-Power Operation Mode
  • Switched 5-V Regulated Output on 5Vg With
    Current Limit
  • Programmable Slew Rate and Frequency
    Modulation for EMI Consideration
  • Reset Function With Deglitch Timer and
    Programmable Delay
  • Alarm Function for Undervoltage Detection and
    Indication
  • Thermally Enhanced Package for Efficient Heat
    Management

The TPIC74100 is a switch-mode regulator with integrated switches for voltage-mode control. With the aid of external components (LC combination), the device regulates the output to 5 V ±3% for a wide input-voltage range.

The TPIC74100 offers a reset function to detect and indicate when the 5-V output rail is outside of the specified tolerance. This reset delay is programmable using an external timing capacitor on the REST pin. Additionally, an alarm (AOUT) feature is activated when the input supply rail Vdriver is below a prescaled specified value (set by the AIN pin).

The TPIC74100 has a frequency-modulation scheme to minimize EMI. The clock modulator permits a modulation of the switching frequency to reduce interference energy in the frequency band.

The 5Vg output is a switched 5-V regulated output with internal current limiting to prevent RESET from being asserted when powering a capacitive load on the supply line. This function is controlled by the 5Vg_ENABLE pin. If there is a short to ground on this output (5Vg output), the output self-protects by operating in a chopping mode. This does, however, increase the output ripple voltage on VOUT during this fault condition.

The TPIC74100 is a switch-mode regulator with integrated switches for voltage-mode control. With the aid of external components (LC combination), the device regulates the output to 5 V ±3% for a wide input-voltage range.

The TPIC74100 offers a reset function to detect and indicate when the 5-V output rail is outside of the specified tolerance. This reset delay is programmable using an external timing capacitor on the REST pin. Additionally, an alarm (AOUT) feature is activated when the input supply rail Vdriver is below a prescaled specified value (set by the AIN pin).

The TPIC74100 has a frequency-modulation scheme to minimize EMI. The clock modulator permits a modulation of the switching frequency to reduce interference energy in the frequency band.

The 5Vg output is a switched 5-V regulated output with internal current limiting to prevent RESET from being asserted when powering a capacitive load on the supply line. This function is controlled by the 5Vg_ENABLE pin. If there is a short to ground on this output (5Vg output), the output self-protects by operating in a chopping mode. This does, however, increase the output ripple voltage on VOUT during this fault condition.
filter Andere AC/DC- und DC/DC-Wandler (integrierter FET) suchen
Herunterladen Video mit Transkript ansehen Video

Ähnliche Produkte, die für Sie interessant sein könnten

open-in-new Alternativen vergleichen
Selbe Funktionalität wie der verglichene Baustein bei abweichender Anschlussbelegung
TPS552872-Q1 AKTIV Vollständig integrierter Abwärts-/Aufwärtswandler, 36 V, 4 A (Automobilindustrie) 36-V, 4-A full integrated buck-boost converter, AEC-Q100 qualified
TPS55289 AKTIV 8-A-Abwärts-/Aufwärtswandler mit I²C-Schnittstelle, 30 V Better power efficiency and higher Iout
TPS552892 AKTIV Vollständig integrierter 36-V-, 8-A-Abwärts-/Aufwärtswandler Better power efficiency and higher Iout
TPS552892-Q1 AKTIV Vollständig integrierter 36-V-, 8-A-Abwärts-/Aufwärtswandler für die Automobilindustrie Better power efficiency and higher Iout

Technische Dokumentation

star =Von TI ausgewählte Top-Empfehlungen für dieses Produkt
Keine Ergebnisse gefunden. Bitte geben Sie einen anderen Begriff ein und versuchen Sie es erneut.
Alle anzeigen 5
Typ Titel Datum
* Data sheet TPIC74100-Q1 Buck and Boost Switch-Mode Regulator datasheet (Rev. B) PDF | HTML 05 Dez 2014
EVM User's guide TPIC74100EVM User's Guide (Rev. A) PDF | HTML 11 Jul 2022
Application note Improve the TPIC74100 Load Transient Performance with Suitable Inductor and Capa 23 Aug 2018
Technical article Solving voltage transient challenges with an integrated buck-boost converter PDF | HTML 12 Mär 2018
Application note TPIC74100-Q1 Buck/Boost Switch Mode Regulator (Rev. B) 22 Sep 2010

Design und Entwicklung

Weitere Bedingungen oder erforderliche Ressourcen enthält gegebenenfalls die Detailseite, die Sie durch Klicken auf einen der unten stehenden Titel erreichen.

Simulationsmodell

TPIC74100 TINA Transient reference design

SLIM325.TSC (366 KB) - TINA-TI Reference Design
Herunterladen
Simulationsmodell

TPIC74100-Q1 PSpice Transient Model

SLIM313.ZIP (73 KB) - PSpice Model
Herunterladen
Simulationsmodell

TPIC74100-Q1 TINA-TI Transient Spice Model

SLIM326.ZIP (44 KB) - TINA-TI Spice Model
Herunterladen
Gehäuse Pins CAD-Symbole, Footprints und 3D-Modelle
HTSSOP (PWP) 20 Ultra Librarian
Es gelten die allgemeinen Geschäftsbedingungen von TI für Evaluierungsartikel.

Bestellen & Qualität

Beinhaltete Information:
  • RoHS
  • REACH
  • Bausteinkennzeichnung
  • Blei-Finish/Ball-Material
  • MSL-Rating / Spitzenrückfluss
  • MTBF-/FIT-Schätzungen
  • Materialinhalt
  • Qualifikationszusammenfassung
  • Kontinuierliches Zuverlässigkeitsmonitoring
Beinhaltete Information:
  • Werksstandort
  • Montagestandort

Support und Schulungen

TI E2E™-Foren mit technischem Support von TI-Ingenieuren

Alle Forenthemen auf Englisch anzeigen

Inhalte werden ohne Gewähr von TI und der Community bereitgestellt. Sie stellen keine Spezifikationen von TI dar. Siehe Nutzungsbedingungen.

Bei Fragen zu den Themen Qualität, Gehäuse oder Bestellung von TI-Produkten siehe TI-Support. ​​​​​​​​​​​​​​

Videos