TPS40422
- Single Supply Operation: 4.5 V to 20 V
- Output Voltage from 0.6 V to 5.6 V
- Dual-output or Two-Phase Synchronous Buck Controller
- PMBus™ Interface Capability
- Margining Up or Down with 2-mV Step
- Programmable Fault Limit and Response
- Output Voltage, Output Current Monitoring
- External Temperature Monitoring with 2N3904 Transistor
- Programmable UVLO ON and OFF Thresholds
- Programmable Soft-start Time and Turn-On and Turn-Off Delay
- On-Chip Non-volatile Memory (NVM) to Store Custom Configurations
- 180° Out-of-Phase to Reduce Input Ripple
- 600-mV Reference Voltage with ±0 .5% Accuracy from 0°C to 85°C
- Inductor DCR Current Sensing
- Programmable Switching Frequency: 200 kHz to 1 MHz
- Voltage Mode Control with Input Feed Forward
- Current Sharing for Multiphase Operation
- Supports Pre-biased Output
- Differential Remote Sensing
- External SYNC
- BPEXT Pin Boosts Efficiency by Supporting External Bias Power Switch Over
- OC, OV, UV, and OT Fault Protection
- 40-Pin, 6 mm × 6 mm VQFN Package with 0.5-mm Pitch
- 40-Pin, 5 mm × 5 mm WQFN Package with 0.4-mm Pitch
- Create a Custom Design using the TPS40422 device with the WEBENCH® Power Designer
The TPS40422 is a dual-output PMBus protocol, synchronous buck controller. It can be configured also for a single, two-phase output.
The wide input range supports 5-V and 12-V intermediate buses. The accurate reference voltage satisfies the need of precision voltage to the modern ASICs and potentially reduces the output capacitance. Voltage mode control reduces noise sensitivity and also ensures low duty ratio conversion.
기술 자료
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하십시오.
7개 모두 보기 유형 | 직함 | 날짜 | ||
---|---|---|---|---|
* | Data sheet | TPS40422 Dual-Output or Two-Phase Synchronous Buck Controller with PMBus™ Interface datasheet (Rev. G) | PDF | HTML | 2022/08/26 |
Application note | Multiphase Buck Design from Start to Finish, Part 1 (Rev. B) | 2021/04/07 | ||
Selection guide | Power Management Guide 2018 (Rev. R) | 2018/06/25 | ||
Application note | SMT Guidelines for Stacked Inductor (Inductor On Top) on Voltage Regulator IC | 2016/02/22 | ||
Technical article | Select the correct PMBus POL solution for your application | PDF | HTML | 2015/08/03 | |
Design guide | TPS40422 Design Example | 2012/02/16 | ||
User guide | Using the PWR091EVM Dual-Output DC/DC Analog With PMBus Interface | 2011/01/05 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
평가 보드
TPS40422EVM-091 — TPS40422 듀얼 출력 또는 다중 페이즈 동기 벅 컨트롤러 평가 모듈
The Texas Instruments TPS40422EVM-091 evaluation module (EVM) helps designers evaluate the performance of the TPS40422 Dual Output or Multiphase Synchronous Buck Controller with PMBus. The EVM is designed to use a regulated 8.0Vdc to 14.0Vdc bus to produce two regulated outputs. One output is (...)
사용 설명서: PDF
애플리케이션 소프트웨어 및 프레임워크
FUSION_DIGITAL_POWER_DESIGNER — 디지털 전원 소프트웨어
Fusion Digital Power™ GUI(그래픽 사용자 인터페이스) 소프트웨어는 선별된 텍사스 인스트루먼트 디지털 파워 컨트롤러와 시퀀서/상태 모니터를 구성하고 모니터링하는 데 사용됩니다. 이 애플리케이션은 PMBus 프로토콜을 사용하여 TI USB 어댑터를 경유, 직렬 버스를 통해 장치와 통신합니다.
애플리케이션 소프트웨어 및 프레임워크
FUSION_MFR_GUI — Fusion Digital Power Manufacturing Tool
The Fusion Digital Power Manufacturing Tool (aka MFR GUI) is a Graphical User Interface used to download firmware, upgrade firmware, configure, calibrate and test .
The MFR GUI supports the same devices as Fusion Digital Power Designer software. This tool is typically used in manufacturing (...)
드라이버 또는 라이브러리
PMBUSSW-LINUX — PMBUS용 Linux 드라이버
The Linux driver supports PMBus controlled Buck Controllers. The Linux driver supports communication through the PMBus and interfaces with the HWMon framework.
Linux Mainline Status
Available in Linux Main line: Yes
Available through git.ti.com: N/A
Supported Devices:
- tps40400
- tps40422
- tps544b20
- tps544b25
- (...)
시뮬레이션 모델
TPS40422_Multiphase_Startup TINA-TI Reference Design
SLUM550.TSC (535 KB) - TINA-TI Reference Design
계산 툴
패키지 | 핀 | CAD 기호, 풋프린트 및 3D 모델 |
---|---|---|
VQFN (RHA) | 40 | Ultra Librarian |
WQFN (RSB) | 40 | Ultra Librarian |
주문 및 품질
포함된 정보:
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
포함된 정보:
- 팹 위치
- 조립 위치