전원 관리 AC/DC 및 DC/DC 컨버터(통합 FET)

TPS546A24A

활성

핀 스트래핑 및 PMBus가 포함된 2.95V~18V 입력, 적층형 10A, 동기 SWIFT™ 벅 컨버터

제품 상세 정보

Rating Catalog Operating temperature range (°C) -40 to 150 Topology Buck Type Converter Iout (max) (A) 10 Vin (min) (V) 2.95 Vin (max) (V) 18 Switching frequency (min) (kHz) 225 Switching frequency (max) (kHz) 1500 Features Adaptive/Dynamic Voltage Scaling, Adjustable current limit, Differential Remote Sense, Enable, Forced PWM, Frequency synchronization, Over Current Protection, PMBus, Phase Interleaving, Power good, Pre-Bias Start-Up, Soft Start Adjustable, Synchronous Rectification, Telemetry, UVLO adjustable, Voltage Margining Control mode current mode Vout (min) (V) 0.25 Vout (max) (V) 5.5 Iq (typ) (µA) 9000 Duty cycle (max) (%) 85
Rating Catalog Operating temperature range (°C) -40 to 150 Topology Buck Type Converter Iout (max) (A) 10 Vin (min) (V) 2.95 Vin (max) (V) 18 Switching frequency (min) (kHz) 225 Switching frequency (max) (kHz) 1500 Features Adaptive/Dynamic Voltage Scaling, Adjustable current limit, Differential Remote Sense, Enable, Forced PWM, Frequency synchronization, Over Current Protection, PMBus, Phase Interleaving, Power good, Pre-Bias Start-Up, Soft Start Adjustable, Synchronous Rectification, Telemetry, UVLO adjustable, Voltage Margining Control mode current mode Vout (min) (V) 0.25 Vout (max) (V) 5.5 Iq (typ) (µA) 9000 Duty cycle (max) (%) 85
LQFN-CLIP (RVF) 40 35 mm² 7 x 5
  • Split rail support: 2.95-V to 18-V PVIN; 2.95-V to 18-V AVIN (4-VIN VDD5 for switching)
  • Integrated 5.5-mΩ/1.8-mΩ MOSFETs
  • Average current mode control with selectable internal compensation
  • 2×, 3×, 4× stackable with current sharing up to 40 A, supporting a single address per output
  • Selectable 0.5-V to 5.5-V output via pin strap or 0.25-V to 5.5-V using PMBus VOUT_COMMAND
  • Extensive PMBus command set with telemetry for VOUT, IOUT and internal die temperature
  • Differential remote sensing with internal FB divider for < 1% VOUT error –40°C to +150°C TJ
  • AVS and margining capabilities through PMBus
  • MSEL pins pin programming PMBus defaults
  • 12 Selectable switching frequencies from 225 kHz to 1.5 MHz (8 pin-strap options)
  • Frequency sync in/sync out
  • Supports prebiased output
  • Supports strongly coupled inductor
  • 7-mm × 5-mm × 1.5-mm, 40-pin QFN, pitch = 0.5 mm
  • Create a Custom Design Using the TPS546A24A With WEBENCH Power Designer
  • Split rail support: 2.95-V to 18-V PVIN; 2.95-V to 18-V AVIN (4-VIN VDD5 for switching)
  • Integrated 5.5-mΩ/1.8-mΩ MOSFETs
  • Average current mode control with selectable internal compensation
  • 2×, 3×, 4× stackable with current sharing up to 40 A, supporting a single address per output
  • Selectable 0.5-V to 5.5-V output via pin strap or 0.25-V to 5.5-V using PMBus VOUT_COMMAND
  • Extensive PMBus command set with telemetry for VOUT, IOUT and internal die temperature
  • Differential remote sensing with internal FB divider for < 1% VOUT error –40°C to +150°C TJ
  • AVS and margining capabilities through PMBus
  • MSEL pins pin programming PMBus defaults
  • 12 Selectable switching frequencies from 225 kHz to 1.5 MHz (8 pin-strap options)
  • Frequency sync in/sync out
  • Supports prebiased output
  • Supports strongly coupled inductor
  • 7-mm × 5-mm × 1.5-mm, 40-pin QFN, pitch = 0.5 mm
  • Create a Custom Design Using the TPS546A24A With WEBENCH Power Designer

The TPS546A24A is a highly integrated, non-isolated DC/DC converter capable of high frequency operation and 10-A current output from a 7-mm × 5-mm package. Two, three, and four TPS546A24A devices can be interconnected to provide up to 40 A on a single output. The device has an option to overdrive the internal 5-V LDO with an external 5-V supply via the VDD5 pin to improve efficiency and reduce power dissipation of the converter.

The TPS546A24A uses a proprietary fixed-frequency current-mode control with input feedforward and selectable internal compensation components for minimal size and stability over a wide range of output capacitances.

The PMBus interface with 1-MHz clock support gives a convenient, standardized digital interface for converter configuration as well as monitoring of key parameters including output voltage, output current, and internal die temperature. Response to fault conditions can be set to restart, latch off, or ignore, depending on system requirements. Back-channel communication between stacked devices enables all TPS546A24Aconverters powering a single output rail to share a single address to simplify system software/firmware design. Key parameters including output voltage, switching frequency, soft-start time, and overcurrent fault limits can also be configured through BOM selection without PMBus communication to support program free power-up.

The TPS546A24A is a highly integrated, non-isolated DC/DC converter capable of high frequency operation and 10-A current output from a 7-mm × 5-mm package. Two, three, and four TPS546A24A devices can be interconnected to provide up to 40 A on a single output. The device has an option to overdrive the internal 5-V LDO with an external 5-V supply via the VDD5 pin to improve efficiency and reduce power dissipation of the converter.

The TPS546A24A uses a proprietary fixed-frequency current-mode control with input feedforward and selectable internal compensation components for minimal size and stability over a wide range of output capacitances.

The PMBus interface with 1-MHz clock support gives a convenient, standardized digital interface for converter configuration as well as monitoring of key parameters including output voltage, output current, and internal die temperature. Response to fault conditions can be set to restart, latch off, or ignore, depending on system requirements. Back-channel communication between stacked devices enables all TPS546A24Aconverters powering a single output rail to share a single address to simplify system software/firmware design. Key parameters including output voltage, switching frequency, soft-start time, and overcurrent fault limits can also be configured through BOM selection without PMBus communication to support program free power-up.

다운로드 스크립트와 함께 비디오 보기 동영상

관심 가지실만한 유사 제품

open-in-new 대안 비교
비교 대상 장치와 동일한 기능을 지원하는 핀 대 핀
TPS546B24A 활성 핀 스트래핑 및 PMBus가 포함된 2.95V~18V 입력, 적층형 20A, 동기형 SWIFT™ 벅 컨버터 Optimized for higher IOUT.
TPS546D24A 활성 핀 스트래핑 및 PMBus®가 포함된 2.95V~16V 입력, 적층형 40A, 동기 SWIFT™ 스텝다운 컨버터 Optimized for higher IOUT.

기술 자료

star =TI에서 선정한 이 제품의 인기 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하십시오.
10개 모두 보기
유형 직함 날짜
* Data sheet TPS546A24A 2.95-V to 18-V, 10-A, up to 4x Stackable, PMBus Buck Cnvtr datasheet (Rev. A) 2020/09/22
Application note Point-of-Load Solutions for Network Interface Cards (NIC) PDF | HTML 2021/09/08
EVM User's guide TPS546A24A SWIFT™ Step-Down Converter Evaluation Module User's Guide (Rev. A) PDF | HTML 2021/04/27
Selection guide Buck Converter Quick Reference Guide (Rev. B) 2021/04/08
Certificate TPS546A24AEVM-1PH EU Declaration of Conformity (DoC) 2020/07/30
Technical article 3 big benefits of small cells PDF | HTML 2020/05/26
Application note Minimize On-Time-Jitter and Ripple by Optimizing Compensation 2020/05/11
Technical article Advantages of scalability: from Peter Parker to pin-strapping PDF | HTML 2020/04/30
Technical article SoC power design: 3 steps to a thermally optimized power supply PDF | HTML 2020/03/09
Application note Powering the TPS546D24A Device Family From a Single 3.3-V Input Power Supply (Rev. A) 2020/03/04

설계 및 개발

추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.

평가 보드

TPS546A24AEVM-1PH — 2.95V~18V, 10A 동기형 벅 평가 모듈

The TPS546A24AEVM-1PH is an evaluation module (EVM) for the TPS546A24A 10-A buck converter. The TPS546A24A device is a stackable synchronous buck with PMBus interface that can operate from a nominal 2.95-V to 18-V supply. The device allows programming and monitoring through the PMBus interface.
사용 설명서: PDF | HTML
TI.com에서 구매 불가
평가 보드

TPS546B24AEVM — 40A, 2상 동기 벅 평가 모듈

The TPS546B24AEVM-2PH evaluation module (EVM) is a 40-A, two-phase buck converter with two TPS546B24A devices. The TPS546B24A device is a stackable synchronous buck with PMBus interface that can operate from a nominal 2.95-V to 18-V supply. The device allows programming and monitoring via the (...)
사용 설명서: PDF | HTML
TI.com에서 구매 불가
평가 보드

TPS546B24AEVM-1PH — 2.95V~18V, 20A 동기형 벅 평가 모듈

The TPS546B24AEVM-1PH is an evaluation module (EVM) for the TPS546B24A 20-A buck converter. The TPS546B24A device is a stackable synchronous buck with PMBus interface that can operate from a nominal 2.95-V to 18-V supply. The device allows programming and monitoring through the PMBus interface.
사용 설명서: PDF | HTML
TI.com에서 구매 불가
평가 보드

TPS546D24SEVM-2PH — TPS546D24S 평가 모듈 고정 주파수 동기 벅 컨버터 2상, 쓰기 잠금 기능 지원

TPS546D24SEVM-2PH 평가 모듈(EVM)은 TPS546D24S 디바이스 2개를 지원하는 2상 벅 컨버터로, 단일 0.8V 출력을 제공합니다. TPS546D24A 디바이스는 PMBus 인터페이스를 지원하는 적층형 동기 벅 컨버터로, 공칭 2.95V~16V 입력 공급으로 작동할 수 있습니다. 이 디바이스를 사용하면 PMBus 인터페이스를 통한 프로그래밍과 모니터링이 가능하며, 사용자 구성 가능한 쓰기 잠금 기능을 통해 보안을 향상시킬 수 있습니다.
사용 설명서: PDF | HTML
TI.com에서 구매 불가
시뮬레이션 모델

TPS546A24A IBIS Model

SLUM710.ZIP (98 KB) - IBIS Model
시뮬레이션 모델

TPS546A24A PSpice Transient Model

SLUM714.ZIP (257 KB) - PSpice Model
시뮬레이션 모델

TPS546B24A SIMPLIS Model

SLUM748.ZIP (1865 KB) - SIMPLIS Model
계산 툴

SLUC686 TPS546x24A Compensation and Pin-Strap Resistor Calculator

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

제품
AC/DC 및 DC/DC 컨버터(통합 FET)
TPS546A24A 핀 스트래핑 및 PMBus가 포함된 2.95V~18V 입력, 적층형 10A, 동기 SWIFT™ 벅 컨버터 TPS546B24A 핀 스트래핑 및 PMBus가 포함된 2.95V~18V 입력, 적층형 20A, 동기형 SWIFT™ 벅 컨버터 TPS546D24A 핀 스트래핑 및 PMBus®가 포함된 2.95V~16V 입력, 적층형 40A, 동기 SWIFT™ 스텝다운 컨버터
계산 툴

SLURB01 TPS546D24A TPS546B24A TPS546A24A Excel Calculator Tool and Checklist

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

제품
AC/DC 및 DC/DC 컨버터(통합 FET)
TPS546A24A 핀 스트래핑 및 PMBus가 포함된 2.95V~18V 입력, 적층형 10A, 동기 SWIFT™ 벅 컨버터 TPS546B24A 핀 스트래핑 및 PMBus가 포함된 2.95V~18V 입력, 적층형 20A, 동기형 SWIFT™ 벅 컨버터 TPS546D24A 핀 스트래핑 및 PMBus®가 포함된 2.95V~16V 입력, 적층형 40A, 동기 SWIFT™ 스텝다운 컨버터
패키지 CAD 기호, 풋프린트 및 3D 모델
LQFN-CLIP (RVF) 40 Ultra Librarian

주문 및 품질

포함된 정보:
  • RoHS
  • REACH
  • 디바이스 마킹
  • 납 마감/볼 재질
  • MSL 등급/피크 리플로우
  • MTBF/FIT 예측
  • 물질 성분
  • 인증 요약
  • 지속적인 신뢰성 모니터링
포함된 정보:
  • 팹 위치
  • 조립 위치

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

콘텐츠는 TI 및 커뮤니티 기고자에 의해 "있는 그대로" 제공되며 TI의 사양으로 간주되지 않습니다. 사용 약관을 참조하십시오.

품질, 패키징, TI에서 주문하는 데 대한 질문이 있다면 TI 지원을 방문하세요. ​​​​​​​​​​​​​​

동영상