TPS65090

활성

스위치 모드 충전기, DCDC 3개, LDO 2개 및 부하 스위치 7개를 갖춘 6V~7V 전원 관리 IC(PMIC)

제품 상세 정보

Regulated outputs (#) 5 Configurability Factory programmable, Software configurable Vin (min) (V) 6 Vin (max) (V) 17 Vout (min) (V) 1 Vout (max) (V) 5 Iout (max) (A) 5 Features Comm control, Power good Step-up DC/DC converter 0 Step-down DC/DC converter 3 Step-down DC/DC controller 0 Step-up DC/DC controller 0 LDO 2 Rating Catalog Switching frequency (max) (kHz) 1840 Operating temperature range (°C) -40 to 85 Shutdown current (ISD) (typ) (µA) 1 Switching frequency (typ) (kHz) 1600 Product type Processor and FPGA
Regulated outputs (#) 5 Configurability Factory programmable, Software configurable Vin (min) (V) 6 Vin (max) (V) 17 Vout (min) (V) 1 Vout (max) (V) 5 Iout (max) (A) 5 Features Comm control, Power good Step-up DC/DC converter 0 Step-down DC/DC converter 3 Step-down DC/DC controller 0 Step-up DC/DC controller 0 LDO 2 Rating Catalog Switching frequency (max) (kHz) 1840 Operating temperature range (°C) -40 to 85 Shutdown current (ISD) (typ) (µA) 1 Switching frequency (typ) (kHz) 1600 Product type Processor and FPGA
VQFN-MR (RVN) 100 See data sheet
  • Wide Input Voltage Charger and Power Path
    Management:
    • VIN Range From 6 V to 17 V
    • Up to 4-A Output Current on the Power Path
    • Switched-Mode Charger; up to 4-A Maximum
      Charge Current
    • JEITA Compliant Charging Control
    • Thermal Regulation, Safety Timers
    • 2 Temperature Sense Inputs
  • 3 Step-Down Converters:
    • High Efficiency Over a Wide Output Current
      Range
    • VIN Range From 6 V to 17 V
    • 2 Fixed Output Voltages (5 V and 3.3 V)
      • Up to 5 A of Continuous Output Current
    • 1 Adjustable Output Voltage (From 1 V to 5 V)
      • Up to 4 A of Continuous Output Current
    • Output Voltage Accuracy ±1%
    • Typical 30-µA Quiescent Current Per
      Converter
  • 2 Always-On LDOs:
    • 2 Fixed Output Voltages (5 V and 3.3 V)
    • Output Voltage Accuracy ±1%
    • Typical 10-µA Quiescent Current per LDO
  • 7 Current-Limited Load Switches:
    • One System Voltage Switch With 1-A Current
      Limit
    • One 5-V Switch With 200-mA Current Limit,
      Reverse-Voltage Protected
    • One 3.3-V Switch With 3-A Current Limit
    • Four 3.3-V Switches With 1-A Current Limit
    • All Switches Controlled by I2C Interface
  • I2C Interface
    • Standard-Mode (100 kHz) Supported
    • Fast-Mode (400 kHz) Supported
    • Fast-Mode Plus (1000 kHz) Supported
    • High-Speed (3.4 MHz) Supported
  • 16-Channel, 10-Bit Analog-to-Digital Converter
    (ADC)
  • Available in a 9-mm × 9-mm, VQFN-100 Package
  • Wide Input Voltage Charger and Power Path
    Management:
    • VIN Range From 6 V to 17 V
    • Up to 4-A Output Current on the Power Path
    • Switched-Mode Charger; up to 4-A Maximum
      Charge Current
    • JEITA Compliant Charging Control
    • Thermal Regulation, Safety Timers
    • 2 Temperature Sense Inputs
  • 3 Step-Down Converters:
    • High Efficiency Over a Wide Output Current
      Range
    • VIN Range From 6 V to 17 V
    • 2 Fixed Output Voltages (5 V and 3.3 V)
      • Up to 5 A of Continuous Output Current
    • 1 Adjustable Output Voltage (From 1 V to 5 V)
      • Up to 4 A of Continuous Output Current
    • Output Voltage Accuracy ±1%
    • Typical 30-µA Quiescent Current Per
      Converter
  • 2 Always-On LDOs:
    • 2 Fixed Output Voltages (5 V and 3.3 V)
    • Output Voltage Accuracy ±1%
    • Typical 10-µA Quiescent Current per LDO
  • 7 Current-Limited Load Switches:
    • One System Voltage Switch With 1-A Current
      Limit
    • One 5-V Switch With 200-mA Current Limit,
      Reverse-Voltage Protected
    • One 3.3-V Switch With 3-A Current Limit
    • Four 3.3-V Switches With 1-A Current Limit
    • All Switches Controlled by I2C Interface
  • I2C Interface
    • Standard-Mode (100 kHz) Supported
    • Fast-Mode (400 kHz) Supported
    • Fast-Mode Plus (1000 kHz) Supported
    • High-Speed (3.4 MHz) Supported
  • 16-Channel, 10-Bit Analog-to-Digital Converter
    (ADC)
  • Available in a 9-mm × 9-mm, VQFN-100 Package

The TPS65090A device is a single-chip power management IC for portable applications consisting of a battery charger with power path management for a dual or triple Li-Ion or Li-Polymer cell battery pack. The charger can be directly connected to an external wall adapter. Three highly efficient step-down converters are targeted for providing a fixed 5-V system voltage, a fixed 3.3-V system voltage, and an adjustable voltage rail. The step-down converters enter a low power mode at light load for maximum efficiency across the widest possible range of load currents. The step-down converters allow the use of small inductors and capacitors to achieve a small solution size. The TPS65090A also integrates two general-purpose always-on LDOs for powering circuit blocks which control the system while shut down. Each LDO operates with an input voltage range from 6 V to 17 V, allowing the LDOs to be supplied from the wall adapter or directly from the main battery pack.

Seven load switches are built into the device. These load switches can be used to control the power supply individually for certain circuit blocks in the application circuit. The current flowing through the load switches, as well as the output current of the step-down converters, the input current from the AC adapter and the charge current is monitored and can be read out using the digital interface.

For all available packages, see the orderable addendum at the end of the data sheet.

The TPS65090A device is a single-chip power management IC for portable applications consisting of a battery charger with power path management for a dual or triple Li-Ion or Li-Polymer cell battery pack. The charger can be directly connected to an external wall adapter. Three highly efficient step-down converters are targeted for providing a fixed 5-V system voltage, a fixed 3.3-V system voltage, and an adjustable voltage rail. The step-down converters enter a low power mode at light load for maximum efficiency across the widest possible range of load currents. The step-down converters allow the use of small inductors and capacitors to achieve a small solution size. The TPS65090A also integrates two general-purpose always-on LDOs for powering circuit blocks which control the system while shut down. Each LDO operates with an input voltage range from 6 V to 17 V, allowing the LDOs to be supplied from the wall adapter or directly from the main battery pack.

Seven load switches are built into the device. These load switches can be used to control the power supply individually for certain circuit blocks in the application circuit. The current flowing through the load switches, as well as the output current of the step-down converters, the input current from the AC adapter and the charge current is monitored and can be read out using the digital interface.

For all available packages, see the orderable addendum at the end of the data sheet.

다운로드 스크립트와 함께 비디오 보기 동영상

기술 자료

star =TI에서 선정한 이 제품의 인기 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하십시오.
11개 모두 보기
유형 직함 날짜
* Data sheet TPS65090 Front-End PMU With Switched-Mode Charger for 2 to 3 Cells In Series datasheet (Rev. B) PDF | HTML 2015/07/13
Application note How to Design Flexible Processor Power Systems Using PMICs (Rev. B) 2020/01/27
Application note Performing Accurate PFM Mode Efficiency Measurements (Rev. A) 2018/12/11
Selection guide Power Management Guide 2018 (Rev. R) 2018/06/25
Application note Optimizing Transient Response of Internally Compensated DC-DC Converters (Rev. B) 2017/11/29
Application note Basic Calculation of a Buck Converter's Power Stage (Rev. B) 2015/08/17
EVM User's guide TPS65090EVM User's Guide (Rev. A) 2013/01/09
Application note Conserving Battery Life when Connecting the TPS65090 to an Unpowered AC Adapter 2012/12/13
Application note How to Measure the Control Loop of DCS-Control Devices (Rev. A) 2012/08/09
Analog Design Journal Design considerations for a resistive feedback divider in a DC/DC converter 2012/04/26
Application note Understanding the Absolute Maximum Ratings of the SW Node (Rev. A) 2012/01/13

설계 및 개발

추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.

평가 보드

TPS65090EVM — 직렬로 2~3셀을 위한 스위치모드 충전기를 지원하는 프론트 엔드 PMU 평가 모듈 보드

TPS65090EVM Frontend PMU With Switchmode Charger for 2-3 Cells In Series Evaluation Module Board

An evaluation module for Texas Instruments TPS65090, Frontend Power Management integrated circuit. The EVM allows for evaluation of the TPS65090 integrated high-input voltage (6V-17V) charger/power (...)
사용 설명서: PDF
TI.com에서 구매 불가
드라이버 또는 라이브러리

TPS65090SW-LINUX — TPS65090용 리눅스 드라이버

The Linux driver supports the TPS65090 Power Management IC. The Linux driver supports communication through the I2C bus and interfaces with the Regulator and Power sub-system.

 

Linux Mainline Status

Available in Linux Main line: Yes
Available through git.ti.com: N/A

Supported Devices:

  • tps65090

 

Linux (...)

평가 모듈(EVM)용 GUI

IPG-UI IPG-UI EVM GUI (Windows Installer)

The IPG-UI GUI can be used to configure multiple PMIC devices to evaluate the features and performance of those devices.  This GUI is built using web-based technologies and supports interacting with the EVM hardware using a USB2ANY adapter board. The USB2ANY Explorer is provided to allow (...)

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

제품
멀티 채널 IC(PMIC)
TPS65020 3개의 DC/DC, 3개의 LDO, I2C 인터페이스 및 동적 전압 스케일링을 지원하는 6채널 전원 관리 IC(PMIC) TPS65023 DC/DC 3개, LDO 3개, I2C 인터페이스 및 DVS를 지원하는 전원 관리 IC(PMIC) TPS65023B DC/DC 3개, LDO 3개, I2C 인터페이스 및 DVS를 지원하는 6채널 전원 관리 IC(PMIC) TPS65055 4개의 낮은 입력 전압 LDO를 지원하는 2.25MHz 듀얼 스텝다운 컨버터 TPS65084 Braswell 프로세서용 프로그래머블 중간 입력 전압 범위 전원 관리 IC(PMIC) TPS65086 2S 및 3S 리튬 이온 배터리 작동 장치 또는 비 배터리 장치용 구성 가능 멀티 레일 PMIC TPS650861 사용자 프로그래머블 3 컨버터, 3 컨트롤러, 4 LDO 및 3 부하 스위치 전원 관리 IC(PMIC) TPS65090 스위치 모드 충전기, DCDC 3개, LDO 2개 및 부하 스위치 7개를 갖춘 6V~7V 전원 관리 IC(PMIC) TPS65094 Apollo Lake 프로세서를 위한 프로그래머블 중간 입력 전압 범위 전원 관리 IC(PMIC) TPS65217 3 DC/DC, 4 LDO, 선형 배터리 충전기 및 백색 LED 드라이버를 지원하는 통합 전원 관리 IC(PMIC) TPS652170 DC/DC 3개, LDO 4개, 배터리 충전기 및 LED 드라이버를 지원하는 사용자 프로그래머블 전원 관리 IC(PMIC) TPS65218 ARM Cortex-A8/A9 SoCs 및 FPGA용 PMIC(통합 전원 관리) TPS6521815 6개의 DC/DC 컨버터, 1개의 LDO 및 3개의 부하 스위치가 있는 사용자 프로그래머블 전원 관리 IC(PMIC) TPS65218D0 ARM® Cortex™-A8/A9 SOC 및 FPGA용 통합 전원 관리(PMIC) TPS657095 임베디드 카메라 모듈 PMIC TPS65910 6x6mm QFN 제품군, 4개의 DC/DC, 8개의 LDO 및 RTC를 지원하는 통합 전원 관리 IC(PMIC) TPS65911 DC/DC 4개, LDO 9개, RTC를 지원하는 통합 전원 관리 IC(PMIC) TPS65912 DC/DC 4개, LDO 10개, LED 출력 3개 및 32kHz RC 오실레이터를 지원하는 전원 관리 IC(PMIC) TPS659128 프로세서 전원용 PMU
하드웨어 개발
평가 보드
BOOSTXL-TPS650861 TPS650861 고객 프로그래밍 BoosterPack TPS65023BEVM-664 TPS65023B 평가 모듈 TPS65023EVM-205 TPS65023 평가 모듈 TPS650860EVM-116 TPS650860 평가 모듈 TPS65218EVM-100 TPS65218 평가 모듈
소프트웨어
평가 모듈(EVM)용 GUI
IPG-UI IPG-UI EVM GUI
평가 모듈(EVM)용 GUI

SLVC469 TPS6509xEVM Software – Legacy

지원되는 제품 및 하드웨어

지원되는 제품 및 하드웨어

제품
멀티 채널 IC(PMIC)
TPS65090 스위치 모드 충전기, DCDC 3개, LDO 2개 및 부하 스위치 7개를 갖춘 6V~7V 전원 관리 IC(PMIC)
하드웨어 개발
평가 보드
TPS65090EVM 직렬로 2~3셀을 위한 스위치모드 충전기를 지원하는 프론트 엔드 PMU 평가 모듈 보드
거버(Gerber) 파일

TPS65090EVM Gerber Files

SLVC472.ZIP (1069 KB)
패키지 CAD 기호, 풋프린트 및 3D 모델
VQFN-MR (RVN) 100 Ultra Librarian

주문 및 품질

포함된 정보:
  • RoHS
  • REACH
  • 디바이스 마킹
  • 납 마감/볼 재질
  • MSL 등급/피크 리플로우
  • MTBF/FIT 예측
  • 물질 성분
  • 인증 요약
  • 지속적인 신뢰성 모니터링
포함된 정보:
  • 팹 위치
  • 조립 위치

권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.

지원 및 교육

TI 엔지니어의 기술 지원을 받을 수 있는 TI E2E™ 포럼

콘텐츠는 TI 및 커뮤니티 기고자에 의해 "있는 그대로" 제공되며 TI의 사양으로 간주되지 않습니다. 사용 약관을 참조하십시오.

품질, 패키징, TI에서 주문하는 데 대한 질문이 있다면 TI 지원을 방문하세요. ​​​​​​​​​​​​​​

동영상