首頁 電源管理 AC/DC 和 DC/DC 轉換器 (整合式 FET)
首頁
電源管理
AC/DC 和 DC/DC 轉換器 (整合式 FET)

LM64460-Q1

現行

車用 3-V 至 36-V、6-A、低 EMI 同步降壓轉換器

立即訂購
產品規格表

LM64460-Q1

現行
產品規格表 立即訂購

產品詳細資料

Rating Automotive Operating temperature range (°C) -40 to 150 TI functional safety category Functional Safety-Capable Topology Buck Type Converter Iout (max) (A) 6 Vin (min) (V) 3 Vin (max) (V) 36 Switching frequency (min) (kHz) 200 Switching frequency (max) (kHz) 2200 Features Enable, Frequency synchronization, Light Load Efficiency, Over Current Protection, Power good, Soft Start Fixed, Spread Spectrum, Synchronous Rectification, Wettable flanks package EMI features Low parasitic Hotrod packaging, Spread Spectrum Vout (min) (V) 1 Vout (max) (V) 34.2 Iq (typ) (µA) 7 Duty cycle (max) (%) 87
Rating Automotive Operating temperature range (°C) -40 to 150 TI functional safety category Functional Safety-Capable Topology Buck Type Converter Iout (max) (A) 6 Vin (min) (V) 3 Vin (max) (V) 36 Switching frequency (min) (kHz) 200 Switching frequency (max) (kHz) 2200 Features Enable, Frequency synchronization, Light Load Efficiency, Over Current Protection, Power good, Soft Start Fixed, Spread Spectrum, Synchronous Rectification, Wettable flanks package EMI features Low parasitic Hotrod packaging, Spread Spectrum Vout (min) (V) 1 Vout (max) (V) 34.2 Iq (typ) (µA) 7 Duty cycle (max) (%) 87
VQFN-FCRLF (RYF) 22 14 mm² 4 x 3.5
  • AEC-Q100 qualified for automotive applications
    • Device temperature grade 1: –40°C to +125°C ambient operating temperature
  • Functional Safety-Capable
  • Versatile synchronous buck DC/DC converter
    • Wide input voltage range of 3V to 36V with tolerance for load-dump transients up to 42V
    • 4A and 6A options available
    • 1% accurate, fixed 3.3V, 5V, or adjustable output voltage from 1V to 95% VIN
    • 150°C maximum junction temperature
    • Fixed 2.1MHz switching frequency (adjustable from 200kHz to 2.2MHz using a SYNC signal)
  • Improved reliability with optimized pinout design and clearance for short-circuit-to-adjacent-pin test
  • Designed for low EMI requirements
    • Enhanced HotRod™ QFN package with dual input paths reduces switch-node ringing
    • Pin-configurable spread spectrum modulation
    • Selectable FPWM or PFM mode at light loads
  • High efficiency across the full load range
    • 92.5% at 13.5VIN, 5VOUT, 6A, 2.1MHz
    • 7µA typical at 3.3VOUT no-load input current
    • 0.6µA typical shutdown quiescent current
    • 0.6V typical dropout at full load
    • External bias option for improved efficiency
  • Create a custom regulator design using the LM644x0-Q1 with WEBENCH Power Designer
  • AEC-Q100 qualified for automotive applications
    • Device temperature grade 1: –40°C to +125°C ambient operating temperature
  • Functional Safety-Capable
  • Versatile synchronous buck DC/DC converter
    • Wide input voltage range of 3V to 36V with tolerance for load-dump transients up to 42V
    • 4A and 6A options available
    • 1% accurate, fixed 3.3V, 5V, or adjustable output voltage from 1V to 95% VIN
    • 150°C maximum junction temperature
    • Fixed 2.1MHz switching frequency (adjustable from 200kHz to 2.2MHz using a SYNC signal)
  • Improved reliability with optimized pinout design and clearance for short-circuit-to-adjacent-pin test
  • Designed for low EMI requirements
    • Enhanced HotRod™ QFN package with dual input paths reduces switch-node ringing
    • Pin-configurable spread spectrum modulation
    • Selectable FPWM or PFM mode at light loads
  • High efficiency across the full load range
    • 92.5% at 13.5VIN, 5VOUT, 6A, 2.1MHz
    • 7µA typical at 3.3VOUT no-load input current
    • 0.6µA typical shutdown quiescent current
    • 0.6V typical dropout at full load
    • External bias option for improved efficiency
  • Create a custom regulator design using the LM644x0-Q1 with WEBENCH Power Designer

The LM644x0-Q1 derives from a family of automotive, synchronous, buck, DC/DC converters with excellent efficiency and ultra-low IQ. With integrated high-side and low-side MOSFETs, up to 6A of output current is delivered over a wide input voltage range from 3V to 36V, with support for load-dump transients up to 42V. The converter implements soft recovery from dropout to eliminate overshoot on the output.

The LM644x0-Q1 incorporates numerous features for excellent EMI performance, including spread-spectrum frequency modulation, a low-EMI Enhanced HotRod QFN package that mitigates switch-node ringing, and a symmetrical pinout for excellent input capacitor placement. The switching frequency is synchronizable between 200kHz and 2.2MHz to avoid sensitive frequency bands, while optimizing efficiency or design size based on the specific requirements of the application.

PFM mode enables frequency foldback during light-load operation, allowing an unloaded current consumption of only 7µA (typical) and high light-load efficiency. A seamless transition between PWM and PFM modes, along with low MOSFET on-resistances and an external bias input, provides exceptional efficiency and thermal performance across the entire load range. The package has several NC pins between critical power pins, which improve the Failure Modes and Effects Analysis (FMEA) result.

The LM644x0-Q1 derives from a family of automotive, synchronous, buck, DC/DC converters with excellent efficiency and ultra-low IQ. With integrated high-side and low-side MOSFETs, up to 6A of output current is delivered over a wide input voltage range from 3V to 36V, with support for load-dump transients up to 42V. The converter implements soft recovery from dropout to eliminate overshoot on the output.

The LM644x0-Q1 incorporates numerous features for excellent EMI performance, including spread-spectrum frequency modulation, a low-EMI Enhanced HotRod QFN package that mitigates switch-node ringing, and a symmetrical pinout for excellent input capacitor placement. The switching frequency is synchronizable between 200kHz and 2.2MHz to avoid sensitive frequency bands, while optimizing efficiency or design size based on the specific requirements of the application.

PFM mode enables frequency foldback during light-load operation, allowing an unloaded current consumption of only 7µA (typical) and high light-load efficiency. A seamless transition between PWM and PFM modes, along with low MOSFET on-resistances and an external bias input, provides exceptional efficiency and thermal performance across the entire load range. The package has several NC pins between critical power pins, which improve the Failure Modes and Effects Analysis (FMEA) result.
filter 尋找其它 AC/DC 和 DC/DC 轉換器 (整合式 FET)
下載 觀看有字幕稿的影片 影片

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 4
類型 標題 日期
* Data sheet LM644x0-Q1 3V to 36V, 4A and 6A, Automotive, Synchronous Buck DC/DC Converters With Pin Selectable Light-Load Mode, Optimized for Reliability and Low EMI datasheet (Rev. B) PDF | HTML 2024年 8月 23日
Functional safety information LM644X0-Q1 Functional Safety FIT Rate, FMD and Pin FMA (Rev. A) PDF | HTML 2024年 6月 4日
User guide LM63460-Q1 and LM64460-Q1 EVM User's Guide PDF | HTML 2021年 12月 16日
Certificate LM64460EVM-2MHZ EU RoHS Declaration of Conformity (DoC) 2021年 12月 9日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

LM64460EVM — LM64460-Q1 評估模組，車用 3V 至 36V、6A、低 EMI 同步降壓轉換器

LM64460EVM-2MHZ 高密度評估模組 (EVM) 的設計目的在於展示 LM64460-Q1 高性能、車用同步降壓 DC/DC 轉換器。EVM 可在 5.5V 至 36V 的廣泛輸入電壓範圍內運作，可提供高於 1% 設定點精度，及高達 6A 輸出電流的固定 5V 輸出。有幾項功能可確保穩壓器在故障狀況下提供防護，包括電壓過低鎖定 (UVLO)、內部緩啟動、斷續模式過電流保護 (OCP)、開漏 PGOOD 指示器，以及過熱自動關機。展頻頻率調變及 FPWM/自動操作模式皆以 LM64460-Q1 的模式/同步針腳進行配置。此外，LM64460-Q1 的預設開關頻率為 (...)

使用指南: PDF | HTML
TI.com 無法提供
計算工具

LM63460-LM64460DESIGN-CALC — LM63440-Q1、LM63460-Q1、LM64440-Q1 和 LM64460-Q1 快速入門設計工具

歡迎使用 LM63440-Q1、LM63460-Q1、LM64440-Q1 和 LM64460-Q1 快速入門設計工具。此獨立工具會加速協助提供電源供應器工程師採用此同步降壓電源轉換器系列的 DC/DC 降壓穩壓器進行設計。因此，使用者可以迅速達到最佳化的設計，以符合應用需求。
View Options
計算工具

SNVR518 — LM63460-Q1 and LM64460-Q1 DC/DC Converter Quickstart Design Tool

Welcome to the LM63440-Q1, LM63460-Q1, LM64440-Q1 and LM64460-Q1 quick start design tool. This standalone tool facilitates and assists the power supply engineer with the design of a DC/DC buck regulator based on this family of synchronous buck power converters. As such, the user can expeditiously (...)

支援產品和硬體

支援產品和硬體

產品
AC/DC 和 DC/DC 轉換器 (整合式 FET)
LM63460-Q1 — 採用強化式 QFN 封裝的車用 3-V 至 36-V、6-A、低 EMI 同步降壓轉換器 LM64460-Q1 — 車用 3-V 至 36-V、6-A、低 EMI 同步降壓轉換器
硬體開發
開發板
LM63460EVM — LM63460-Q1 評估模組，車用 5.5-V 至 36-V、6-A、低 EMI 同步降壓轉換器
下載
PCB 佈局

LM63460-Q1, LM64460-Q1 EVM PCB Layout Files

SNVR515.ZIP (5089 KB)
下載
封裝 針腳 CAD 符號、佔位空間與 3D 模型
VQFN-FCRLF (RYF) 22 Ultra Librarian
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 認證摘要
  • 進行中持續性的可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片